Investigation of the Hydrodynamic Characteristics of Asymmetric Cross-Sections Advancing in Regular Waves

2011 ◽  
Author(s):  
Sergio Ribeiro e Silva ◽  
Emre Uzunoglu ◽  
Carlos Guedes Soares ◽  
Adolfo Maro´n ◽  
Cesar Gutierrez
Keyword(s):  
Cross Sections ◽  
Forced Oscillation ◽  
Hydrodynamic Characteristics ◽  
Hydrodynamic Coefficients ◽  
Parametric Rolling ◽  
Captive Model Tests ◽  
Strip Theory ◽  
Added Masses ◽  
Decay Tests ◽  
Hull Forms

A series of experiments were carried out to assess the instantaneous hydrodynamic coefficients and the parametric rolling characteristics of a C11 class container vessel model. The experiments consisted of captive model tests at various heel angles, forced oscillation tests, free roll decay tests and parametric rolling tests. The results obtained from the forced oscillation tests in calm water on symmetric (upright) and asymmetric (heeled) cross-sections are discussed in here. The main objective of the forced oscillation tests was to obtain the heave, roll and pitch added masses and damping coefficients for two different speeds and also three different amplitudes of forced motions. The most important aspect was to assess the influence of taking instantaneous cross-section into account on calculation of these hydrodynamic coefficients. In addition, these tests allowed the identification of the level of non-linear effects with the amplitude of the forced motions for both symmetric and asymmetric hull forms. The experimental data obtained is compared with the results from two strip theory codes for symmetric and asymmetric cross-sections.

Study on the Hydrodynamic Characteristics for Heave Plate Structure of Truss Spar

2010 ◽  
Author(s):  
Wenjun Shen ◽  
Yougang Tang ◽  
Liqin Liu
Keyword(s):  
Numerical Simulations ◽  
Forced Oscillation ◽  
Hydrodynamic Performance ◽  
Hydrodynamic Characteristics ◽  
Hydrodynamic Coefficients ◽  
Plate Structure ◽  
Plate Spacing ◽  
Mesh Method ◽  
Truss Spar ◽  
Heave Plate

The hydrodynamic characteristics of heave plates are studied in this paper. Firstly, different motion amplitudes and plate spacing influencing hydrodynamic coefficients are considered. Secondly, heave plates with different thicknesses are calculated, the case of edges with inclined form for heave plate is also taken into account. Numerical simulations are made for the plate forced oscillation, employing the dynamic mesh method and UDF (User defined functions). The values of Cm and Cd for heave plate are calculated. It is found that, in a certain amplitude range, Cm increases with increasing of amplitudes, Cd decreases with increasing of amplitudes. The values of Cm and Cd increase with increasing of plate spacing. Furthermore with the same effective thickness, the hydrodynamic performance of heave plate with inclined form is improved greatly.

Numerical Investigation of Parametric Rolling of a Container Ship in Regular and Irregular Waves

2017 ◽  
Author(s):  
Suresh Rajendran ◽  
C. Guedes Soares
Keyword(s):  
Incident Wave ◽  
Radiation Force ◽  
Wave Profile ◽  
Irregular Waves ◽  
Container Ship ◽  
Hydrodynamic Coefficients ◽  
Parametric Rolling ◽  
Nonlinear Radiation ◽  
Strip Theory ◽  
Radiation Forces

Parametric rolling of a post-Panamax C11 class containership in regular and irregular waves is numerically investigated using body nonlinear time domain methods based on strip theory. The Froude-Krylov and the hydrostatic forces are calculated for the exact wetted surface area under the undisturbed incident wave profile. Two kinds of formulations are used for calculation of the radiation forces. The first one employs a linear radiation force in which the frequency dependent hydrodynamic coefficients are calculated for mean position of the sections at mean water level. The second formulation calculates the hydrodynamic coefficients for the exact submerged depth of ship sections under the undisturbed incident wave profile, and hence called as body nonlinear radiation force. The numerical results from the aforementioned formulations are compared with each other, and also with experimental results obtained from a wave tank in both regular and irregular waves. For all the cases in regular waves, the vulnerability to parametric rolling is clearly identified by the numerical models, even though a few discrepancies are observed in the estimation of the severity (maximum roll angle) of the problem. In this paper, the effects of the linear and body nonlinear radiation forces on the numerical calculation of parametric rolling of a container ship and the ability of the numerical methods to identify parametric rolling are investigated.

Numerical evaluation of hydrodynamic characteristics of planing hulls by using a hybrid method

2021 ◽  
pp. 147509022199024
Author(s):  
Emre Kahramanoglu ◽  
Silvia Pennino ◽  
Huseyin Yilmaz
Keyword(s):  
Experimental Data ◽  
Hybrid Method ◽  
Design Stage ◽  
Hydrodynamic Characteristics ◽  
Calm Water ◽  
Preliminary Design Stage ◽  
Reduction Function ◽  
Hull Forms ◽  
Good Agreement

The hydrodynamic characteristics of the planing hulls in particular at the planing regime are completely different from the conventional hull forms and the determination of these characteristics is more complicated. In the present study, calm water hydrodynamic characteristics of planing hulls are investigated using a hybrid method. The hybrid method combines the dynamic trim and sinkage from the Zarnick approach with the Savitsky method in order to calculate the total resistance of the planing hull. Since the obtained dynamic trim and sinkage values by using the original Zarnick approach are not in good agreement with experimental data, an improvement is applied to the hybrid method using a reduction function proposed by Garme. The numerical results obtained by the hybrid and improved hybrid method are compared with each other and available experimental data. The results indicate that the improved hybrid method gives better results compared to the hybrid method, especially for the dynamic trim and resistance. Although the results have some discrepancies with experimental data in terms of resistance, trim and sinkage, the improved hybrid method becomes appealing particularly for the preliminary design stage of the planing hulls.

Determination of the added masses and damping coefficients during coupled motions of two ships in shallow water parallel to the vertical wall

2021 ◽  
pp. 16-25
Author(s):  
В.Ю. Семенова ◽  
К.И. Баканов
Keyword(s):  
Shallow Water ◽  
Vertical Wall ◽  
Three Dimensional ◽  
Hydrodynamic Coefficients ◽  
Damping Coefficients ◽  
Added Masses ◽  
Joint Motions ◽  
National Practice ◽  
Simultaneous Influence

В статье рассматривается определение коэффициентов демпфирования и присоединенных масс, возникающих при совместной качке двух судов в условиях мелководья параллельно вертикальной стенке на основании решения трехмерной потенциальной задачи. Определение гидродинамических коэффициентов осуществляется на основании методов интегральных уравнений и зеркальных отображений. Представленное решение в отечественной практике является новым. В статье приводятся результаты расчетов коэффициентов присоединенных масс и демпфирования, возникающих при качке двух одинаковых судов, расположенных лагом к волнению и параллельно вертикальной стенке в зависимости от изменения расстояний как между судами, так и между судами и вертикальной стенкой. Проводится исследование влияния различных фарватеров на величины гидродинамических коэффициентов, а именно: мелководного фарватера, мелководного фарватера с вертикальной стенкой, мелководного фарватера со вторым параллельно качающимся судном и мелководного фарватера с вертикальной стенкой и вторым судном. Таким образом, в работе учитывается одновременное влияния мелководья, вертикальной стенки и второго судна. Показано увеличение значений коэффициентов присоединенных масс и демпфирования при уменьшении расстояний между судами и между судами и вертикальной стенкой. Также показано значительное совместное влияние вертикальной стенки и второго судна на коэффициенты присоединенных масс и демпфирования по сравнению с другими видами стесненных фарватеров. The article discusses the determination of damping coefficients and added masses arising from the joint motions of two ships in shallow water conditions parallel to the vertical wall based on the solution of a three-dimensional potential problem. Determination of hydrodynamic coefficients is carried out on the basis of the methods of integral equations and mirror images. The solution presented in the national practice is new The article presents the results of calculating the coefficients of added masses and damping arising from the motions of two identical ships located lagged to the sea and parallel to the vertical wall, depending on the change in the distances between the ships and between the ships and the vertical wall. A study is being made of the influence of various waterways on the values ​​of hydrodynamic coefficients, namely: a shallow waterway, a shallow waterway with a vertical wall, a shallow waterway with a second parallel oscillating ship and a shallow waterway with a vertical wall and a second ship. Thus, the work takes into account the simultaneous influence of shallow water, vertical wall and the second ship. An increase in the values of the coefficients of added masses and damping with a decrease in the distances between ships and between ships and the vertical wall is shown. It also shows a significant combined effect of the vertical wall and the second ship on the added mass and damping coefficients in comparison with other types of constrained waterways.

RANS Study on Hydrodynamic Characteristics of Flapped Rudders

2018 ◽  
Author(s):  
Jialun Liu ◽  
Robert Hekkenberg ◽  
Bingqian Zhao
Keyword(s):  
Yangtze River ◽  
Area Ratio ◽  
Hydrodynamic Characteristics ◽  
Hydrodynamic Coefficients ◽  
Sectional Area ◽  
The Yangtze River ◽  
Long Distance ◽  
Ansys Fluent ◽  
Rans Simulations ◽  
Rudder Angle

Ships that equipped with flapped rudders have better manoeuvring performance than ships fitted with traditional spade rudders. Moreover, this advantage is achieved without significantly affecting the ship’s resistance during normal cruising. Flapped rudders are, therefore, favourable for ships that require high manoeuvring performance and sail long distance. Nowadays, there is a trend of using twin flapped rudders on newly built inland vessels in the Yangtze River. To properly design these ships and analyse their manoeuvring performance, the hydrodynamic characteristics of the flapped rudders are required. In this paper, a RANS study is performed to analyse the impacts of the three main properties of a flapped rudder on its hydrodynamic coefficients. The target properties are the rudder profile, the flap-linkage ratio (the flapped angle relative to the rudder chord line divided by the applied rudder angle), and the flap-area ratio (the sectional area of the flap divided by the total sectional area). The RANS simulations are carried out with commercial meshing tool ANSYS Meshing and CFD solver ANSYS Fluent.

Forced oscillation experiments

1991 ◽  
Vol 334 (1634) ◽  
pp. 199-211
Keyword(s):  
Numerical Methods ◽  
Water Depth ◽  
Forced Oscillation ◽  
Vertical Plane ◽  
Forced Oscillations ◽  
Hydrodynamic Characteristics ◽  
Scale Models ◽  
Ship Speed

Forced oscillation experiments with scale models are carried out to determine hydrodynamic characteristics of ships, with respect to motions in waves or steering and manoeuvring qualities. Depending on the considered motion components, in a horizontal or vertical plane, various methods are used to induce forced oscillations which are discussed briefly. Some results of forced oscillation experiments are presented as examples of this technique and compared with calculations based on numerical methods. The comparisons include, among others, the effects of ship speed and restricted water depth.

scholarly journals Bilge Keel Induced Roll Damping of an FPSO With Sponsons

2016 ◽  
Author(s):  
Babak Ommani ◽  
Nuno Fonseca ◽  
Trygve Kristiansen ◽  
Christopher Hutchison ◽  
Hanne Bakksjø
Keyword(s):  
Free Surface ◽  
Two Dimensions ◽  
The Body ◽  
Proximity Effects ◽  
Roll Damping ◽  
Damping Coefficients ◽  
Free Decay ◽  
Strip Theory ◽  
Decay Tests ◽  
Bilge Keel

The bilge keel induced roll damping of an FPSO with sponsons is investigated numerically and experimentally. The influence of the bilge keel size, on the roll damping is studied. Free decay tests of a three-dimensional ship model, for three different bilge keel sizes are used to determine roll damping coefficients. The dependency of the quadratic roll damping coefficient to the bilge keel height and the vertical location of the rotation center is studied using CFD. A Navier-Stokes solver based on the Finite Volume Method is adopted for solving the laminar flow of incompressible water around a section of the FPSO undergoing forced roll oscillations in two-dimensions. The free-surface condition is linearized by neglecting the nonlinear free-surface terms and the influence of viscous stresses in the free surface zone, while the body-boundary condition is exact. An averaged center of rotation is estimated by comparing the results of the numerical calculations and the free decay tests. The obtained two-dimensional damping coefficients are extrapolated to 3D by use of strip theory argumentations and compared with the experimental results. It is shown that this simplified approach can be used for evaluating the bilge keel induced roll damping with efficiency, considering unconventional ship shapes and free-surface proximity effects.

Comparison of Ship-Motion Theory and Experiment for Destroyer with Large Bulb

1970 ◽  
Vol 14 (01) ◽  
pp. 67-75
Author(s):  
W.E. Smith ◽  
N. Salvesen
Keyword(s):  
Satisfactory Agreement ◽  
Small Amplitude ◽  
Ship Motion ◽  
Experimental Techniques ◽  
Strip Theory ◽  
Free Running ◽  
Hull Forms ◽  
Theory And Experiment

Experimental techniques for measuring pitch and heave motions for hull forms with large bulbous bows are investigated. It is found that free-running tests in regular small-amplitude waves give the most accurate results. A comparison of the pitch and heave amplitudes and phases obtained by the experiment and by the Korvin-Kroukovsky strip theory shows satisfactory agreement. It is concluded that with sufficiently accurate section representation, the strip theory can be used to predict head-seas motions not only for regular hull forms, but also for ships with bulbous bows and sonar arrays in small-amplitude waves.

Sign in / Sign up

Export Citation Format

Share Document