Deterministic Simulation of Breaking Wave Impact and Flexible Response of a Fixed Offshore Wind Turbine

2015 ◽  
Author(s):  
Tim Bunnik ◽  
Joop Helder ◽  
Erik-Jan de Ridder
Keyword(s):  
Numerical Model ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Breaking Waves ◽  
Model Tests ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Wave Loads ◽  
Wave Impact ◽  
Flexible Response

The effects of operational wave loads and wind loads on offshore mono pile wind turbines are well understood. For most sites, however, the water depth is such that breaking or near-breaking waves will occur causing impulsive excitation of the mono pile and consequently considerable stresses, displacements and accelerations in the mono pile, tower and turbine. Model tests with a flexible mono pile wind turbine were carried out to investigate the effect of breaking waves. In these model tests the flexibility of the turbine was realistically modelled. These model tests were used for validation of a numerical model for the flexible response of wind turbines due to breaking waves. A focusing wave group has been selected which breaks just aft of the wind turbine. The numerical model consists of a one-way coupling between a CFD model for breaking wave loads and a simplified structural model based on mode shapes. An iterative wave calibration technique has been developed in the CFD method to ensure a good match between the measured and simulated incoming wave profile. This makes a deterministic comparison between simulations and measurements possible. This iteration is carried out in a 2D CFD domain (long-crested wave restriction) and is therefore relatively cheap. The calibrated CFD wave is then simulated in a (shorter) 3D CFD domain including a (fixed) wind turbine. The resulting wave pressures on the turbine have been used to compute the modal excitation and subsequently the modal response of the wind turbine. The horizontal accelerations resulting from this one-way coupling are in good agreement with the measured accelerations.

Impact of New Slamming Wave Design Method on the Structural Dynamics of a Classic, Modern and Future Offshore Wind Turbine

2017 ◽  
Author(s):  
Johan M. Peeringa ◽  
Koen W. Hermans
Keyword(s):  
Wind Turbine ◽  
Wave Train ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Wave Loads ◽  
Wave Load ◽  
Wave Impact ◽  
The Impact

In the WiFi-JIP project, the impact of steep (and breaking) waves on a monopile support structure was studied. Observations during model tests showed that large tower top accelerations occur due to a slamming wave. Using experiments and simulations results, a new formulation of the design load for a slamming wave was developed. Instead of the embedded stream function, as applied in industry, the wave train is generated with the nonlinear potential flow code Oceanwave3D. On the wave train a set of conditions is applied to find the individual waves, that are closest to the prescribed breaking wave and most likely cause a slamming impact. To study the effect of the new slamming load formulation on different sized offshore wind turbines, aero-hydroelastic simulations were performed on a classic 3MW wind turbine, a modern 4MW wind turbine and a future 10MW wind turbine. The simulations are performed with and without a slamming wave load. The slamming has a clear effect on the tower top acceleration. Accelerations due to the wave impact are highest for the 3MW model at the tower top and at 50m height. A serious tower top acceleration of almost 7m/s2 due to wave slamming is found for the 3MW turbine. This is an increase of 474% compared with the case of Morison wave loads only.

The Dynamic Response of an Offshore Wind Turbine With Realistic Flexibility to Breaking Wave Impact

2011 ◽  
Author(s):  
Erik Jan de Ridder ◽  
Pieter Aalberts ◽  
Joris van den Berg ◽  
Bas Buchner ◽  
Johan Peeringa
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Breaking Waves ◽  
Impulsive Loading ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Extreme Waves ◽  
Wave Impact ◽  
Pilot Model

The effects of operational loads and wind loads on offshore monopile wind turbines are well understood. For most sites, however, the water depth is such that breaking or near-breaking waves will occur causing impulsive excitation of the monopile and consequently considerable stresses and displacements in the monopile, tower and turbine. To investigate this, pilot model tests were conducted with a special model of an offshore wind turbine with realistic flexibility tested in (extreme) waves. This flexibility was considered to be necessary for two reasons: the impulsive loading of extreme waves is very complex and there can be an interaction between this excitation and the dynamic response of the foundation and tower. The tests confirmed the importance of the topic of breaking waves: horizontal accelerations of more than 0.5g were recorded at nacelle level in extreme cases.

Using Nonlinear Wave Kinematics to Estimate the Loads on Offshore Wind Turbines in 3-Hour Sea States

2018 ◽  
Author(s):  
Tim Bunnik ◽  
Erik-Jan de Ridder
Keyword(s):  
Wind Turbine ◽  
Nonlinear Wave ◽  
Wind Turbines ◽  
Wave Model ◽  
Breaking Waves ◽  
Model Tests ◽  
Offshore Wind ◽  
Wave Loads ◽  
Offshore Wind Turbines ◽  
Wave Basin

The effects of operational wave loads and wind loads on offshore mono pile wind turbines are well understood. For most sites, however, the water depth is such that breaking or near-breaking waves will occur causing impulsive excitation of the mono pile and consequently considerable stresses, displacements and accelerations in the monopile, tower and turbine. As has been shown in earlier, recent publications, Computational Fluid Dynamics (CFD) can be used to accurately analyze wave impacts on offshore wind turbines. However, it is not yet well suited to study the statistical variability of wave impact loads in long-duration sea states, and thus estimate the ULS and ALS loads for which a wind turbine has to be designed. An alternative, simplified approach, is the use of a Morison model in which the kinematics (water particle velocities and accelerations) from a nonlinear wave model are used. For long-crested waves the nonlinear wave model can be run in a 2D mode and is therefore relatively cheap. In this paper model tests for steep and breaking waves on an offshore wind turbine are compared with results from the Morison model. First, a deterministic comparison is made between the wave loads from the model tests and the simulation model (simulating the same 3-hour wave realization as in the basin), which turns out to be difficult because of differences between wave reflections in the wave basin (a physical beach) and the numerical wave model (absorbing boundary condition). Second, a statistical comparison is made by comparing with different wave realizations measured in the wave basin.

Experimental Investigations of Breaking Wave Impact Forces on a Monopile Substructure for Offshore Wind Turbines Under Regular Breaking Waves

2017 ◽  
Author(s):  
Vipin Chakkurunni Palliyalil ◽  
Panneer Selvam Rajamanickam ◽  
Mayilvahanan Alagan Chella ◽  
Vijaya Kumar Govindasamy
Keyword(s):  
Circular Cylinder ◽  
Wind Turbines ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Wave Impact ◽  
Offshore Wind Turbines ◽  
Impact Forces ◽  
The Impact

The main objective of the paper is to investigate wave impact forces from breaking waves on a monopile substructure for offshore wind turbine in shallow waters. This study examines the load assessment parameters relevant for breaking wave forces on a vertical circular cylinder subjected to breaking waves. Experiments are conducted in a shallow water flume and the wave generation is based on piston type wave maker. The experiments are performed with a vertical circular cylinder with diameter, D = 0.20m which represents a monopile substructure for offshore wind turbines with regular waves of frequencies around 0.8Hz. The experimental setup consists of a 1/10 slope followed by a horizontal bed portion with a water depth of 0.8m. Plunging breaking waves are generated and free surface elevations are measured at different locations along the wave tank from wave paddle to the cylinder in order to find the breaking characteristics. Wave impact pressures are measured on the cylinder at eight different vertical positions along the height of the cylinder under breaking waves for different environmental conditions. The wave impact pressures and wave surface elevations in the vicinity of the cylinder during the impact for three different wave conditions are presented and discussed.

Numerical Modeling of Breaking Wave Kinematics and Wave Impact Pressures on a Vertical Slender Cylinder

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
Mayilvahanan Alagan Chella ◽  
Hans Bihs ◽  
Dag Myrhaug ◽  
Øivind Asgeir Arntsen
Keyword(s):  
Free Surface ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Total Force ◽  
Wave Loads ◽  
Wave Impact ◽  
Large Wave ◽  
Surface Deformations

Wave loads from breaking waves on offshore wind turbine (OWT) substructures in shallow waters still remain uncertain. The interaction of breaking waves with structures is characterized by complex free surface deformations, instantaneous impact of the water mass against the structure, and consequently large wave forces on the structures. The main objective of the paper is to investigate wave impact pressures and kinematics during the interaction of breaking waves with a vertical cylinder using the open-source computational fluid dynamics (CFD) model REEF3D. The model is based on the Reynolds-averaged Navier–Stokes (RANS) equations coupled with the level set method and k–ω turbulence model. Three wave impact conditions are considered in this study. The numerically simulated free surface deformations around the cylinder during the breaking wave interaction are also presented for different wave impact conditions. For three wave impact conditions, the wave impact pressure and the horizontal and vertical components of the particle velocity are computed in front of the cylinder and analyzed. The pressure and velocity profile at their maximum values are also examined and discussed. In addition, the total force is calculated for three breaking conditions and they are correlated with the pressure and kinematics during the interaction.

scholarly journals The Effect of the Second-Order Wave Loads on Drift Motion of a Semi-Submersible Floating Offshore Wind Turbine

2020 ◽  
Vol 8 (11) ◽  
pp. 859
Author(s):  
Thanh-Dam Pham ◽  
Hyunkyoung Shin
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Second Order ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Wave Loads ◽  
Hydrodynamic Loads ◽  
Drift Motion ◽  
Offshore Wind Turbines ◽  
Floating Offshore Wind Turbines

Floating offshore wind turbines (FOWTs) have been installed in Europe and Japan with relatively modern technology. The installation of floating wind farms in deep water is recommended because the wind speed is stronger and more stable. The design of the FOWT must ensure it is able to withstand complex environmental conditions including wind, wave, current, and performance of the wind turbine. It needs simulation tools with fully integrated hydrodynamic-servo-elastic modeling capabilities for the floating offshore wind turbines. Most of the numerical simulation approaches consider only first-order hydrodynamic loads; however, the second-order hydrodynamic loads have an effect on a floating platform which is moored by a catenary mooring system. At the difference-frequencies of the incident wave components, the drift motion of a FOWT system is able to have large oscillation around its natural frequency. This paper presents the effects of second-order wave loads to the drift motion of a semi-submersible type. This work also aimed to validate the hydrodynamic model of Ulsan University (UOU) in-house codes through numerical simulations and model tests. The NREL FAST code was used for the fully coupled simulation, and in-house codes of UOU generates hydrodynamic coefficients as the input for the FAST code. The model test was performed in the water tank of UOU.

Analysis of Octagonal Pile Supporting Offshore Wind Turbines Under Wave Loads

2014 ◽  
Author(s):  
Serena Lim ◽  
Longbin Tao
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Computational Cost ◽  
Offshore Wind ◽  
Computational Time ◽  
Offshore Wind Turbine ◽  
Wave Loads ◽  
Element Method

Offshore wind energy development has gained considerable momentum around the world as wind is stronger and steadier offshore compared to land. This has led to a significant increase in production in recent years, especially offshore wind turbine embedded in shallow waters, such as the recent large scale offshore wind farms in the Northern Europe region. Being at the offshore waters, the wind turbines are subjected to harsh environment. The pile supporting the wind turbine must be reliable and able to withstand such sea condition. It is an important part of the design to study the structural behaviour of the piles under the wave loads. Due to the significant capital cost associated with the fabrication of the large circular cylinders, a new recommended innovative design to overcome such problem is to substitute the circular cylinder with a vertical monopile of octagonal cross-sectional shape. This paper describes the development of an efficient numerical model for structural analysis of wave interaction with octagonal pile using a modified semi analytical Scaled Boundary Finite Element Method (SBFEM). In contrast to the existing solutions obtained using the traditional methods such as the Finite Element Method (FEM) which typically suffer from high computational cost and the Boundary Element Method (BEM) which faces limitation from fundamental equations and problems with singularities. The most prominent advantage that SBFEM has over the FEM is in terms of the number of elements used for calculation and hence a reduction in computational time. When compared with BEM, the SBFEM does not suffer from computational stability problems.

Breaking Wave Impacts on Offshore Wind Turbine Foundations: Focused Wave Groups and CFD

2010 ◽  
Author(s):  
Henrik Bredmose ◽  
Niels G. Jacobsen
Keyword(s):  
Breaking Waves ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Wave Loads ◽  
Simple Method ◽  
Wave Groups ◽  
Line Force ◽  
Focused Wave ◽  
Spilling Breakers

Extreme wave loads from breaking waves on a monopile foundation are computed within a 3D CFD model. The wave impacts are obtained by application of focused wave groups. For a fixed position of the monopile, the focus location of the wave group is varied to produce impacts with front shapes that varies from early stages of breaking to broken waves. The CFD results for in-line force are compared to load estimates obtained from the Morison equation. The peak loads determined with this simple method are smaller than those of the CFD solution. The computational results appear to suggest that for the impacts of spilling breakers the peak force gets smaller the more developed the breaking is. This is in qualitative agreement with a finding from shallow water impacts on vertical walls: the strongest wave loads are associated with breakers that hit the structure with slightly overturning front. Extensions of the study are discussed.

scholarly journals A Simulation of Non-Simultaneous Ice Crushing Force for Wind Turbine Towers with Large Slopes

Energies ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2608 ◽  
Author(s):  
Li Zhou ◽  
Shifeng Ding ◽  
Ming Song ◽  
Junliang Gao ◽  
Wei Shi
Keyword(s):  
Numerical Model ◽  
Wind Turbine ◽  
Ice Sheet ◽  
Model Tests ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Foundation Design ◽  
Cold Regions ◽  
Crushing Force ◽  
Ice Loads

When the offshore wind energy industry attempts to develop in cold regions, ice load becomes the main technological challenge for offshore wind turbine foundation design. Dynamic ice loads acting on wind turbine foundations should be calculated in a reasonable way. The scope of this study is to present a numerical model that considers the non-simultaneous ice crushing failure acting on the vertical structure of a wind turbine’s foundation. The local ice crushing force at the contact surface between the ice sheet and structure is calculated. The boundary of the ice sheet is updated at each time step based on the indentation length of the ice sheet according to its structure. Ice loads are validated against two model tests with three different structure models developed by other researchers. The time series of the ice forces derived from the simulation and model tests are compared. The proposed numerical model can capture the main trends of ice–wind turbine foundation interaction. The simulation results agree well with measured data from the model tests in terms of maximum ice force, which is a key factor for wind turbine design. The proposed model will be helpful for assisting the initial design of wind turbine foundations in cold regions.

Sign in / Sign up

Export Citation Format

Share Document