Experimental Investigations of Breaking Wave Impact Forces on a Monopile Substructure for Offshore Wind Turbines Under Regular Breaking Waves

2017 ◽  
Author(s):  
Vipin Chakkurunni Palliyalil ◽  
Panneer Selvam Rajamanickam ◽  
Mayilvahanan Alagan Chella ◽  
Vijaya Kumar Govindasamy
Keyword(s):  
Circular Cylinder ◽  
Wind Turbines ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Wave Impact ◽  
Offshore Wind Turbines ◽  
Impact Forces ◽  
The Impact

The main objective of the paper is to investigate wave impact forces from breaking waves on a monopile substructure for offshore wind turbine in shallow waters. This study examines the load assessment parameters relevant for breaking wave forces on a vertical circular cylinder subjected to breaking waves. Experiments are conducted in a shallow water flume and the wave generation is based on piston type wave maker. The experiments are performed with a vertical circular cylinder with diameter, D = 0.20m which represents a monopile substructure for offshore wind turbines with regular waves of frequencies around 0.8Hz. The experimental setup consists of a 1/10 slope followed by a horizontal bed portion with a water depth of 0.8m. Plunging breaking waves are generated and free surface elevations are measured at different locations along the wave tank from wave paddle to the cylinder in order to find the breaking characteristics. Wave impact pressures are measured on the cylinder at eight different vertical positions along the height of the cylinder under breaking waves for different environmental conditions. The wave impact pressures and wave surface elevations in the vicinity of the cylinder during the impact for three different wave conditions are presented and discussed.

Impact of New Slamming Wave Design Method on the Structural Dynamics of a Classic, Modern and Future Offshore Wind Turbine

2017 ◽  
Author(s):  
Johan M. Peeringa ◽  
Koen W. Hermans
Keyword(s):  
Wind Turbine ◽  
Wave Train ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Wave Loads ◽  
Wave Load ◽  
Wave Impact ◽  
The Impact

In the WiFi-JIP project, the impact of steep (and breaking) waves on a monopile support structure was studied. Observations during model tests showed that large tower top accelerations occur due to a slamming wave. Using experiments and simulations results, a new formulation of the design load for a slamming wave was developed. Instead of the embedded stream function, as applied in industry, the wave train is generated with the nonlinear potential flow code Oceanwave3D. On the wave train a set of conditions is applied to find the individual waves, that are closest to the prescribed breaking wave and most likely cause a slamming impact. To study the effect of the new slamming load formulation on different sized offshore wind turbines, aero-hydroelastic simulations were performed on a classic 3MW wind turbine, a modern 4MW wind turbine and a future 10MW wind turbine. The simulations are performed with and without a slamming wave load. The slamming has a clear effect on the tower top acceleration. Accelerations due to the wave impact are highest for the 3MW model at the tower top and at 50m height. A serious tower top acceleration of almost 7m/s2 due to wave slamming is found for the 3MW turbine. This is an increase of 474% compared with the case of Morison wave loads only.

Modeling Breaking Waves for Fixed-Bottom Support Structures for Offshore Wind Turbines

2018 ◽  
Author(s):  
Hannah M. Johlas ◽  
Spencer Hallowell ◽  
Shengbai Xie ◽  
Pedro Lomonaco ◽  
Matthew A. Lackner ◽  
...  
Keyword(s):  
Wind Turbines ◽  
Water Depth ◽  
Adaptive Mesh Refinement ◽  
Adaptive Mesh ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Breaking Wave ◽  
Intermediate Water ◽  
Offshore Wind Turbines ◽  
Ocean Conditions

Fixed-bottom offshore wind turbines (OWTs) are typically located in shallow to intermediate water depth, where waves are likely to break. Support structure designs for such turbines must account for loads due to breaking waves, but predictions from breaking wave models often disagree with each other and with observed behavior. This variability indicates the need for a better understanding of each model’s strengths and limitations, especially for different ocean conditions. This work evaluates and improves the accuracy of common breaking wave criteria through comparison to Computational Fluid Dynamics (CFD) simulations of breaking waves. The simulated ocean conditions are representative of potential U.S. East Coast offshore wind energy development sites, but the discussion of model accuracy and limitations can be applied to any location with similar ocean conditions. The waves are simulated using CONVERGE, a commercial CFD software that uses a Volume of Fluid (VOF) approach and includes adaptive mesh refinement at the evolving air-water interface. First, the CFD model is validated against experimental data for shoaling and breaking wave surface elevations. Second, 2D simulations of breaking waves are compared to widely-used breaking wave limits (McCowan, Miche, and Goda) for different combinations of wave height, wavelength, water depth, and seafloor slope. Based on these comparisons, the accuracy and limitations of each breaking limit model are discussed. General usage guidelines are then recommended.

The Dynamic Response of an Offshore Wind Turbine With Realistic Flexibility to Breaking Wave Impact

2011 ◽  
Author(s):  
Erik Jan de Ridder ◽  
Pieter Aalberts ◽  
Joris van den Berg ◽  
Bas Buchner ◽  
Johan Peeringa
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Breaking Waves ◽  
Impulsive Loading ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Extreme Waves ◽  
Wave Impact ◽  
Pilot Model

The effects of operational loads and wind loads on offshore monopile wind turbines are well understood. For most sites, however, the water depth is such that breaking or near-breaking waves will occur causing impulsive excitation of the monopile and consequently considerable stresses and displacements in the monopile, tower and turbine. To investigate this, pilot model tests were conducted with a special model of an offshore wind turbine with realistic flexibility tested in (extreme) waves. This flexibility was considered to be necessary for two reasons: the impulsive loading of extreme waves is very complex and there can be an interaction between this excitation and the dynamic response of the foundation and tower. The tests confirmed the importance of the topic of breaking waves: horizontal accelerations of more than 0.5g were recorded at nacelle level in extreme cases.

Comparison of Epoxy Coating Degradations Under Impingement Flow and Stationary Immersion

2020 ◽  
Author(s):  
Amin Vedadi ◽  
M. Subbir Parvej ◽  
Xinnan Wang ◽  
Yechun Wang
Keyword(s):  
Wind Turbines ◽  
Sea Water ◽  
Electrochemical Impedance ◽  
Epoxy Coating ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Corrosive Environment ◽  
Nacl Solution ◽  
Offshore Wind Turbines ◽  
The Impact

Abstract Offshore wind turbines are considered as a reliable source of electricity generation. However, due to the large cost of the construction and installation of offshore wind turbines, most wind turbines are designed to operate for more than 20 years. One of the biggest issues which causes a severe damage to the construction of wind turbines is the existence of a very corrosive environment including large mechanical loads applied to the construction by the waves and the high concentration of salt and other chemicals in the sea water. The construction of offshore wind turbine can be divided into four main regions based on the types of exposure to the water and the corrosive environment, including submerged zone, tidal zone, splash zone, and atmospheric zone. In this study, experiments were conducted to compare the impact of impingement flow of 3.5 w.t.% NaCl solution on the epoxy coating samples to the exposure of the same type of samples to a stationary 3.5 w.t.% NaCl solution. Those two exposure conditions correspond to the environments at the top and the bottom part of the submerged zone of offshore wind turbines respectively. Electrochemical Impedance Spectroscopy (EIS) method was used to monitor the degradation of organic coatings. The surface roughness was measured by Atomic Force Microscope (AFM). The roughness of the coated surfaces before and after the exposure was compared. For the two different flow conditions, i.e. impingement flow and stationary immersion, significant differences have been discovered from the EIS results and AFM results. We observed a more severe degradation in the epoxy coatings in impingement flow, and a rougher surface is formed for coating samples subjected to impingement flow.

Deterministic Simulation of Breaking Wave Impact and Flexible Response of a Fixed Offshore Wind Turbine

2015 ◽  
Author(s):  
Tim Bunnik ◽  
Joop Helder ◽  
Erik-Jan de Ridder
Keyword(s):  
Numerical Model ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Breaking Waves ◽  
Model Tests ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Wave Loads ◽  
Wave Impact ◽  
Flexible Response

The effects of operational wave loads and wind loads on offshore mono pile wind turbines are well understood. For most sites, however, the water depth is such that breaking or near-breaking waves will occur causing impulsive excitation of the mono pile and consequently considerable stresses, displacements and accelerations in the mono pile, tower and turbine. Model tests with a flexible mono pile wind turbine were carried out to investigate the effect of breaking waves. In these model tests the flexibility of the turbine was realistically modelled. These model tests were used for validation of a numerical model for the flexible response of wind turbines due to breaking waves. A focusing wave group has been selected which breaks just aft of the wind turbine. The numerical model consists of a one-way coupling between a CFD model for breaking wave loads and a simplified structural model based on mode shapes. An iterative wave calibration technique has been developed in the CFD method to ensure a good match between the measured and simulated incoming wave profile. This makes a deterministic comparison between simulations and measurements possible. This iteration is carried out in a 2D CFD domain (long-crested wave restriction) and is therefore relatively cheap. The calibrated CFD wave is then simulated in a (shorter) 3D CFD domain including a (fixed) wind turbine. The resulting wave pressures on the turbine have been used to compute the modal excitation and subsequently the modal response of the wind turbine. The horizontal accelerations resulting from this one-way coupling are in good agreement with the measured accelerations.

Numerical Modeling of Breaking Wave Kinematics and Wave Impact Pressures on a Vertical Slender Cylinder

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
Mayilvahanan Alagan Chella ◽  
Hans Bihs ◽  
Dag Myrhaug ◽  
Øivind Asgeir Arntsen
Keyword(s):  
Free Surface ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Total Force ◽  
Wave Loads ◽  
Wave Impact ◽  
Large Wave ◽  
Surface Deformations

Wave loads from breaking waves on offshore wind turbine (OWT) substructures in shallow waters still remain uncertain. The interaction of breaking waves with structures is characterized by complex free surface deformations, instantaneous impact of the water mass against the structure, and consequently large wave forces on the structures. The main objective of the paper is to investigate wave impact pressures and kinematics during the interaction of breaking waves with a vertical cylinder using the open-source computational fluid dynamics (CFD) model REEF3D. The model is based on the Reynolds-averaged Navier–Stokes (RANS) equations coupled with the level set method and k–ω turbulence model. Three wave impact conditions are considered in this study. The numerically simulated free surface deformations around the cylinder during the breaking wave interaction are also presented for different wave impact conditions. For three wave impact conditions, the wave impact pressure and the horizontal and vertical components of the particle velocity are computed in front of the cylinder and analyzed. The pressure and velocity profile at their maximum values are also examined and discussed. In addition, the total force is calculated for three breaking conditions and they are correlated with the pressure and kinematics during the interaction.

Irregular Nonlinear Wave Simulation and Associated Loads on Offshore Wind Turbines

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
E. Marino ◽  
H. Nguyen ◽  
C. Lugni ◽  
L. Manuel ◽  
C. Borri
Keyword(s):  
Wind Turbine ◽  
Nonlinear Wave ◽  
Wind Turbines ◽  
Breaking Waves ◽  
Design Guidelines ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Wave Modeling ◽  
Linear Solution ◽  
Offshore Wind Turbines

The accuracy of predicted loads on offshore wind turbines depends on the mathematical models employed to describe the combined action of the wind and waves. Using a global simulation framework that employs a domain-decomposition strategy for computational efficiency, this study investigates the effects of nonlinear waves on computed loads on the support structure (monopile) and the rotor–nacelle assembly of a bottom-supported offshore wind turbine. The fully nonlinear (FNL) numerical wave solver is invoked only on subdomains where nonlinearities are detected; thus, only locally in space and time, a linear solution (and associated Morison hydrodynamics) is replaced by the FNL one. An efficient carefully tuned linear–nonlinear transition scheme makes it possible to run long simulations such that effects from weakly nonlinear up to FNL events, such as imminent breaking waves, can be accounted for. The unsteady nonlinear free-surface problem governing the propagation of gravity waves is formulated using potential theory and a higher-order boundary element method (HOBEM) is used to discretize Laplace’s equation. The FNL solver is employed and associated hydrodynamic loads are simulated in conjunction with aerodynamic loads on the rotor of a 5-MW wind turbine using the NREL open-source software, fast. We assess load statistics associated with a single severe sea state. Such load statistics are needed in evaluating relevant load cases specified in offshore wind turbine design guidelines; in this context, the influence of nonlinear wave modeling and its selection over alternative linear or linearized wave modeling is compared. Ultimately, a study such as this one will seek to evaluate long-term loads using the FNL solver in computations directed toward reliability-based design of offshore wind turbines where a range of sea states will need to be evaluated.

scholarly journals Maintenance Planning of Offshore Wind Turbine Using Condition Monitoring Information

2009 ◽  
Author(s):  
Jose´ G. Rangel-Rami´rez ◽  
John D. So̸rensen
Keyword(s):  
Condition Monitoring ◽  
Wind Turbines ◽  
Wind Farm ◽  
Offshore Structures ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Maintenance Planning ◽  
Offshore Wind Turbines ◽  
Inspection And Maintenance ◽  
Monitoring Information

Deterioration processes such as fatigue and corrosion are typically affecting offshore structures. To “control” this deterioration, inspection and maintenance activities are developed. Probabilistic methodologies represent an important tool to identify the suitable strategy to inspect and control the deterioration in structures such as offshore wind turbines (OWT). Besides these methods, the integration of condition monitoring information (CMI) can optimize the mitigation activities as an updating tool. In this paper, a framework for risk-based inspection and maintenance planning (RBI) is applied for OWT incorporating CMI, addressing this analysis to fatigue prone details in welded steel joints at jacket or tripod steel support structures for offshore wind turbines. The increase of turbulence in wind farms is taken into account by using a code-based turbulence model. Further, additional modes t integrate CMI in the RBI approach for optimal planning of inspection and maintenance. As part of the results, the life cycle reliabilities and inspection times are calculated, showing that earlier inspections are needed at in-wind farm sites. This is expected due to the wake turbulence increasing the wind load. With the integration of CMI by means Bayesian inference, a slightly change of first inspection times are coming up, influenced by the reduction of the uncertainty and harsher or milder external agents.

scholarly journals Improving the Strategy of Maintaining Offshore Wind Turbines through Petri Net Modelling

2021 ◽  
Vol 11 (2) ◽  
pp. 574
Author(s):  
Rundong Yan ◽  
Sarah Dunnett
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Petri Net ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Maintenance Costs ◽  
Offshore Wind Turbines ◽  
Major Repair ◽  
Wind Turbine System ◽  
Periodic Maintenance

In order to improve the operation and maintenance (O&M) of offshore wind turbines, a new Petri net (PN)-based offshore wind turbine maintenance model is developed in this paper to simulate the O&M activities in an offshore wind farm. With the aid of the PN model developed, three new potential wind turbine maintenance strategies are studied. They are (1) carrying out periodic maintenance of the wind turbine components at different frequencies according to their specific reliability features; (2) conducting a full inspection of the entire wind turbine system following a major repair; and (3) equipping the wind turbine with a condition monitoring system (CMS) that has powerful fault detection capability. From the research results, it is found that periodic maintenance is essential, but in order to ensure that the turbine is operated economically, this maintenance needs to be carried out at an optimal frequency. Conducting a full inspection of the entire wind turbine system following a major repair enables efficient utilisation of the maintenance resources. If periodic maintenance is performed infrequently, this measure leads to less unexpected shutdowns, lower downtime, and lower maintenance costs. It has been shown that to install the wind turbine with a CMS is helpful to relieve the burden of periodic maintenance. Moreover, the higher the quality of the CMS, the more the downtime and maintenance costs can be reduced. However, the cost of the CMS needs to be considered, as a high cost may make the operation of the offshore wind turbine uneconomical.

Sign in / Sign up

Export Citation Format

Share Document