Experimental Study on Flow-Induced Vibration of Floating Squared Section Cylinders With Low Aspect Ratio: Part II — Effects of Rounded Edges

2016 ◽  
Author(s):  
Rodolfo T. Gonçalves ◽  
Dennis M. Gambarine ◽  
Aline M. Momenti ◽  
Felipe P. Figueiredo ◽  
André L. C. Fujarra
Keyword(s):  
Aspect Ratio ◽  
Reynolds Numbers ◽  
Ocean Basin ◽  
Separation Point ◽  
Flow Induced Vibration ◽  
Low Aspect Ratio ◽  
Aspect Ratios ◽  
Significant Difference ◽  
Flow Induced Vibrations ◽  
Elastically Supported

Experiments regarding flow-induced vibration on floating rounded squared section cylinders with low aspect ratio were carried out in an ocean basin equipped with a rotating-arm apparatus. Floating squared section cylinders with rounded edges and aspect ratios of L/D = 2.0 were elastically supported by a set of linear springs in order to provide low structural damping to the system. Two different incidence angles were tested, namely 0 and 45 degrees. The Reynolds numbers covered the range from 2,000 to 30,000. The aim was to understand the flow-induced vibrations around single columns, gathering information for further understanding the causes for the Vortex-Induced Motions in semi-submersible and TLP platforms. Experiments on circular and squared sections cylinders (without rounded edges) were also carried out to compare the results with the rounded square section cylinders (with rounded edges). The amplitude results for in-line, transverse and yaw amplitude for 0-degree models showed to be higher for squared section cylinders compared to those for the rounded square section cylinders. No significant difference between the 45-degree models was observed. The results of ratio between frequency of motion in the transverse direction and natural frequency in still water confirmed the vortex-induced vibration behavior for the squared and rounded square section cylinders for 45-degree incidence; and also the galloping characteristics for 0-degree incidence cases. The rounded effect on the square section cylinders showed to be important only for reduced velocity larger than 8, which is probably related to the position of the separation point that changes around the rounded edge, behavior that did not occurr for the squared edge that fixed the separation point for any reduced velocity.

Experimental Study on Flow-Induced Vibration of Floating Squared Section Cylinders With Low Aspect Ratio: Part I — Effects of Incidence Angle

2015 ◽  
Author(s):  
Rodolfo T. Gonçalves ◽  
Dênnis M. Gambarine ◽  
Felipe P. Figueiredo ◽  
Fábio V. Amorim ◽  
André L. C. Fujarra
Keyword(s):  
Aspect Ratio ◽  
Incidence Angle ◽  
Ocean Basin ◽  
Circular Cylinders ◽  
Structural Damping ◽  
Flow Induced Vibration ◽  
Double Frequency ◽  
Low Aspect Ratio ◽  
Aspect Ratios ◽  
Elastically Supported

Experiments regarding flow-induced vibration on floating squared section cylinders with low aspect ratio were carried out in an ocean basin with rotating-arm apparatus. The floating squared section cylinders were elastically supported by a set of linear springs to provide low structural damping to the system. Three different aspect ratios were tested, namely L/D = 1.0, 2.0 and 3.0, and two different incidence angles, namely 0 and 45 degrees. The aims were to understanding the flow-induced vibration around single columns of multi-column platforms, such as semi-submersible and TLP. VIV on circular cylinders were also carried out to compare the results. The range of Reynolds number covered was 2,000 < Re < 27,000. The in-line and transverse amplitude results showed to be higher for 45-degree incidence compared with 0-degree, but the maximum amplitudes for squared section cylinders were lower compared with the circular ones. The double frequency in the in-line motion was not verified as in circular cylinders. The yaw amplitudes cannot be neglected for squared section cylinders, maximum yaw amplitudes around 10 degrees were observed for reduced velocities up to 15.

Cross-Wind Influence on Low Aspect Ratio Wings at Low Reynolds Numbers

2013 ◽  
Author(s):  
Amir Karimi Noughabi ◽  
Mehran Tadjfar
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Micro Air Vehicles ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Low Aspect Ratio ◽  
Aspect Ratios ◽  
Lift And Drag ◽  
Lift And Drag Coefficient

The aerodynamics of the low aspect ratio (LAR) wings is of outmost importance in the performance of the fixed-wing micro air vehicles (MAVs). The flow around these wings is widely influenced by three dimensional (3D) phenomena: including wing-tip vortices, formation of laminar bubble, flow separation and reattachment, laminar to turbulent transition or any combination of these phenomena. All the recent studies consider the aerodynamic characteristics of the LAR wings under the effect of the direct wind. Here we focus on the numerical study of the influence of cross-wind on flow over the inverse Zimmerman wings with the aspect ratios (AR) between 1 and 2 at Reynolds numbers between 6×104 and 105. We have considered cross-wind’s angles from 0° to 40° and angle of attack from 0° to 12°. The results show that lift and drag coefficient generally decrease when the angle of the cross-wind is increased.

Reynolds-number scaling of vortex pinch-off on low-aspect-ratio propulsors

2016 ◽  
Vol 799 ◽  
Author(s):  
John N. Fernando ◽  
David E. Rival
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Time Scales ◽  
Early Stage ◽  
Reynolds Numbers ◽  
Growth Time ◽  
Flat Plates ◽  
Low Aspect Ratio ◽  
Drag Forces ◽  
Aspect Ratios

Impulsively started, low-aspect-ratio elliptical flat plates have been investigated experimentally to understand the vortex pinch-off dynamics at transitional and fully turbulent Reynolds numbers. The range of Reynolds numbers investigated is representative of those observed in animals that employ rowing and paddling modes of drag-based propulsion and manoeuvring. Elliptical flat plates with five aspect ratios ranging from one to two have been considered, as abstractions of propulsor planforms found in nature. It has been shown that Reynolds-number scaling is primarily determined by plate aspect ratio in terms of both drag forces and vortex pinch-off. Due to vortex-ring growth time scales that are longer than those associated with the development of flow instabilities, the scaling of drag is Reynolds-number-dependent for the aspect-ratio-one flat plate. With increasing aspect ratio, the Reynolds-number dependency decreases as a result of the shorter growth time scales associated with high-aspect-ratio elliptical vortex rings. Large drag peaks are observed during early-stage vortex growth for the higher-aspect-ratio flat plates. The collapse of these peaks with Reynolds number provides insight into the evolutionary convergence process of propulsor planforms used in drag-based swimming modes over diverse scales towards aspect ratios greater than one.

Heat Transfer for High Aspect Ratio Rectangular Channels in a Stationary Serpentine Passage With Turbulated and Smooth Surfaces

2013 ◽  
Author(s):  
Matthew A. Smith ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Aspect Ratio ◽  
Flow Behavior ◽  
Reynolds Numbers ◽  
Hydraulic Diameter ◽  
Internal Cooling ◽  
Number Range ◽  
Aspect Ratios ◽  
Parallel Configuration

Heat transfer distributions are presented for a stationary three passage serpentine internal cooling channel for a range of engine representative Reynolds numbers. The spacing between the sidewalls of the serpentine passage is fixed and the aspect ratio (AR) is adjusted to 1:1, 1:2, and 1:6 by changing the distance between the top and bottom walls. Data are presented for aspect ratios of 1:1 and 1:6 for smooth passage walls and for aspect ratios of 1:1, 1:2, and 1:6 for passages with two surfaces turbulated. For the turbulated cases, turbulators skewed 45° to the flow are installed on the top and bottom walls. The square turbulators are arranged in an offset parallel configuration with a fixed rib pitch-to-height ratio (P/e) of 10 and a rib height-to-hydraulic diameter ratio (e/Dh) range of 0.100 to 0.058 for AR 1:1 to 1:6, respectively. The experiments span a Reynolds number range of 4,000 to 130,000 based on the passage hydraulic diameter. While this experiment utilizes a basic layout similar to previous research, it is the first to run an aspect ratio as large as 1:6, and it also pushes the Reynolds number to higher values than were previously available for the 1:2 aspect ratio. The results demonstrate that while the normalized Nusselt number for the AR 1:2 configuration changes linearly with Reynolds number up to 130,000, there is a significant change in flow behavior between Re = 25,000 and Re = 50,000 for the aspect ratio 1:6 case. This suggests that while it may be possible to interpolate between points for different flow conditions, each geometric configuration must be investigated independently. The results show the highest heat transfer and the greatest heat transfer enhancement are obtained with the AR 1:6 configuration due to greater secondary flow development for both the smooth and turbulated cases. This enhancement was particularly notable for the AR 1:6 case for Reynolds numbers at or above 50,000.

Power Augmentation of a HAWT by Mie-type Tip Vanes, considering Wind Tunnel Flow Visualisation, Blade-Aspect Ratios and Reynolds Number

2003 ◽  
Vol 27 (3) ◽  
pp. 183-194 ◽  
Author(s):  
Yukimaru Shimizu ◽  
Edmond Ismaili ◽  
Yasunari Kamada ◽  
Takao Maeda
Keyword(s):  
Reynolds Number ◽  
Wind Tunnel ◽  
Aspect Ratio ◽  
Reynolds Numbers ◽  
Flow Visualisation ◽  
Velocity Measurements ◽  
Horizontal Axis Wind Turbine ◽  
Aspect Ratios ◽  
Detailed Surface ◽  
Blade Tips

Wind tunnel results are reported concerning the effects of blade aspect ratio and Reynolds number on the performance of a horizontal axis wind turbine (HAWT) with Mie-type1 tip attachments. The flow behaviour around the blade tips and the Mie-type tip vanes is presented. Detailed surface oil film visualization and velocity measurements around the blade tips, with and without Mie vanes, were obtained with the two-dimensional, Laser-Doppler Velocimetry method. Experiments were performed with rotors having blades with different aspect ratio and operating at different Reynolds numbers. The properties of the vortices generated by the Mie vanes and the blade tips were carefully studied. It was found that increased power augmentation by Mie vanes is achieved with blades having smaller aspect ratio and smaller Reynolds number.

Topology of vortex breakdown in closed polygonal containers

2017 ◽  
Vol 820 ◽  
pp. 263-283 ◽  
Author(s):  
Igor V. Naumov ◽  
Irina Yu. Podolskaya
Keyword(s):  
Aspect Ratio ◽  
Cross Section ◽  
Vortex Breakdown ◽  
Laser Doppler Anemometry ◽  
Reynolds Numbers ◽  
Cylindrical Container ◽  
Stagnation Points ◽  
Aspect Ratios ◽  
Particle Visualization ◽  
Cross Section Geometry

The topology of vortex breakdown in the confined flow generated by a rotating lid in a closed container with a polygonal cross-section geometry has been analysed experimentally and numerically for different height/radius aspect ratios $h$ from 0.5 to 3.0. The locations of stagnation points of the breakdown bubble emergence and corresponding Reynolds numbers were determined experimentally and numerically by STAR-CCM+ computational fluid dynamics software for square, pentagonal, hexagonal and octagonal cross-section configurations. The flow pattern and velocity were observed and measured by combining seeding particle visualization and laser Doppler anemometry. The vortex breakdown size and position on the container axis were identified for Reynolds numbers ranging from 500 to 2800 in steady flow conditions. The obtained results were compared with the flow structure in the closed cylindrical container. The results allowed revealing regularities of formation of the vortex breakdown bubble depending on $Re$ and $h$ and the cross-section geometry of the confined container. It was found in a diagram of $Re$ versus $h$ that reducing the number of cross-section angles from eight to four shifts the breakdown bubble location to higher Reynolds numbers and a smaller aspect ratio. The vortex breakdown bubble area for octagonal cross-section was detected to correspond to the one for the cylindrical container but these areas for square and cylindrical containers do not overlap in the entire range of aspect ratio.

Sign in / Sign up

Export Citation Format

Share Document