Numerical Investigations on Aerodynamic Performance of Nozzle Control Stage of a 600MW Steam Turbine Under Different Backing Pressure Conditions

2011 ◽  
Author(s):  
Gangyun Zhong ◽  
Jun Li ◽  
Zhigang Li ◽  
Xin Yan ◽  
Qilin Wu
Keyword(s):  
Steam Turbine ◽  
Control Valve ◽  
Aerodynamic Performance ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Computational Domain ◽  
Aerodynamic Efficiency ◽  
Control Stage ◽  
Backing Pressure ◽  
Partial Admission

Partial admission aerodynamic performance of a nozzle control stage for a 600MW steam turbine was numerically investigated using the Reynolds-Averaged Navier-Stokes (RANS) solutions. Two inlet main steam pipe, four control valves, four nozzle groups including strengthening ribs and full stator blades, and full rotor blades were considered in the present computational domain. The partial admission with three control vales opening and the fourth control valve closed under five different backing pressures were calculated to analyze the aerodynamic efficiency and total pressure losses distributions. The maximum aerodynamic efficiency of the nozzle control stage was obtained at five different backing pressure operating conditions. The flow fields in the nozzle control stage at specified backing pressure with consideration of the partial admissions effects were also illustrated.

Unsteady Load of Partial Admission Control Stage Rotor of a Large Power Steam Turbine

2004 ◽  
Author(s):  
Piotr Lampart ◽  
Mariusz Szymaniak ◽  
Romuald Rza˛dkowski
Keyword(s):  
Steam Turbine ◽  
Rotor Blades ◽  
Pressure Pulsations ◽  
Unsteady Forces ◽  
Large Power ◽  
Control Stage ◽  
Partial Admission ◽  
Geometrical Imperfections ◽  
Sst Turbulence Model ◽  
2D Model

Partial admission flow in the control stage of a 200MW steam turbine is investigated with the help of a RANS solver with k-ω SST turbulence model in the code Fluent. A 2D model of flow at the mid-span section of the full annulus is assumed. The results exhibit interesting details of the process of expansion in the control stage. Unsteady forces acting on the single rotor blades of the control stage are calculated, and are subject to Fourier analysis. Single blade forces are summed up to obtain the unsteady load at the rotor (forces acting at the rotor disc are neglected due to the assumed 2D model). The calculations take into account pressure pulsations at the entry to the nozzle boxes and rotor blade mistuning / geometrical imperfections.

Performance Characterization of a Twin Scroll Volute for Turbocharging Applications

2018 ◽  
Author(s):  
Carlo Cravero ◽  
Mario La Rocca ◽  
Andrea Ottonello
Keyword(s):  
Experimental Data ◽  
Scientific Literature ◽  
Aerodynamic Performance ◽  
Operating Conditions ◽  
Automatic Design ◽  
Cfd Model ◽  
Radial Turbine ◽  
Wide Range ◽  
Partial Admission

The use of twin scroll volutes in radial turbine for turbocharging applications has several advantages over single passage volute related to the engine matching and to the overall compactness. Twin scroll volutes are of increasing interest in power unit development but the open scientific literature on their performance and modelling is still quite limited. In the present work the performance of a twin scroll volute for a turbocharger radial turbine are investigated in some detail in a wide range of operating conditions at both full and partial admission. A CFD model for the volute have been developed and preliminary validated against experimental data available for the radial turbine. Then the numerical model has been used to generate the database of solutions that have been investigated and used to extract the performance. Different parameters and indices are introduced to describe the volute aerodynamic performance in the wide range of operating conditions chosen. The above parameters can be used for volute development or matching with a given rotor or efficiently implemented in automatic design optimization strategies.

Influence of a Cylindrical Exhaust Hood Installation on the Last Stage Rotor Blades of a Low Pressure Model Steam Turbine

2017 ◽  
Author(s):  
Fabian F. Müller ◽  
Markus Schatz ◽  
Damian M. Vogt ◽  
Jens Aschenbruck
Keyword(s):  
Flow Field ◽  
Steam Turbine ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Pressure Measurements ◽  
Exhaust Hood ◽  
Blade Vibration ◽  
Time Resolved ◽  
Vibration Behavior ◽  
Last Stage

The influence of a cylindrical strut shortly downstream of the bladerow on the vibration behavior of the last stage rotor blades of a single stage LP model steam turbine was investigated in the present study. Steam turbine retrofits often result in an increase of turbine size, aiming for more power and higher efficiency. As the existing LP steam turbine exhaust hoods are generally not modified, the last stage rotor blades frequently move closer to installations within the exhaust hood. To capture the influence of such an installation on the flow field characteristics, extensive flow field measurements using pneumatic probes were conducted at the turbine outlet plane. In addition, time-resolved pressure measurements along the casing contour of the diffuser and on the surface of the cylinder were made, aiming for the identification of pressure fluctuations induced by the flow around the installation. Blade vibration behavior was measured at three different operating conditions by means of a tip timing system. Despite the considerable changes in the flow field and its frequency content, no significant impact on blade vibration amplitudes were observed for the investigated case and considered operating conditions. Nevertheless, time-resolved pressure measurements suggest that notable pressure oscillations induced by the vortex shedding can reach the upstream bladerow.

Unsteady Forces of Rotor Blades in Full and Partial Admission Turbines

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Narmin Baagherzadeh Hushmandi ◽  
Jens E. Fridh ◽  
Torsten H. Fransson
Keyword(s):  
Pressure Field ◽  
Dynamic Pressure ◽  
Turbine Blades ◽  
Leading Edge ◽  
Rotational Frequency ◽  
Rotor Blades ◽  
Computational Domain ◽  
Unsteady Forces ◽  
Partial Admission ◽  
Unsteady Force

A numerical and experimental study of partial admission in a low reaction two-stage axial air test turbine is performed in this paper. In order to model one part load configuration, corresponding to zero flow in one of the admission arcs, the inlet was blocked at one segmental arc, at the leading edge of the first stage guide vanes. Due to the unsymmetrical geometry, the full annulus of the turbine was modeled numerically. The computational domain contained the shroud and disk cavities. The full admission turbine configuration was also modeled for reference comparisons. Computed unsteady forces of the first stage rotor blades showed cyclic change both in magnitude and direction while moving around the circumference. Unsteady forces of first stage rotor blades were plotted in the frequency domain using Fourier analysis. The largest amplitudes caused by partial admission were at first and second multiples of rotational frequency due to the existence of single blockage and change in the force direction. Unsteady forces of rotating blades in a partial admission turbine could cause unexpected failures in operation; therefore, knowledge about the frequency content of the unsteady force vector and the related amplitudes is vital to the design process of partial admission turbine blades. The pressure plots showed that the nonuniformity in the static pressure field decreases considerably downstream of the second stage’s stator row, while the nonuniformity in the dynamic pressure field is still large. The numerical results between the first stage’s stator and rotor rows showed that the leakage flow leaves the blade path down into the disk cavity in the admitted sector and re-enters downstream of the blocked channel. This process compensates for the sudden pressure drop downstream of the blockage but reduces the momentum of the main flow.

Rotordynamic Stability Under Partial Admission Conditions in a Large Power Steam Turbine

2009 ◽  
Author(s):  
Lin Gao ◽  
Yiping Dai ◽  
Zhiqiang Wang ◽  
Yatao Xu ◽  
Qingzhong Ma
Keyword(s):  
Steam Turbine ◽  
Fluid Model ◽  
Rotor System ◽  
System Stability ◽  
Steam Turbines ◽  
Large Power ◽  
Control Stage ◽  
Partial Admission ◽  
The Stability ◽  
Load Conditions

At present, the majority of power steam turbines operate under part-load conditions during most of their working time in accordance with the fluctuation of power supply. The load governing method may cause partial admission in control stage and even some pressure stages, which impacts much on the stability of the rotor system. In this paper, CFD and FEM method were used to analyze the effect of partial admission on rotor system stability. A new approach is proposed to simplify the 3D fluid model for a partial admission control stage. Rotordynamic analysis was carried out to test the stability of the HP rotor of a 600 MW steam turbine under different load conditions. 13 different governing modes on the rotor stability were conducted and data were analyzed. It is found that rotor stability varies significantly with different governing modes and mass flow rates, which is consistent with the operation. Asymmetric fluid forces resulted from partial admission cause a fluctuation of the dynamic characteristics of the HP bearings, which consequently affect the stability of the rotor system. One of the nozzle governing modes in which the diagonal valves open firstly is demonstrated as the optimal mode with the maximum system stability. The optimization has been applied to 16 power generation units in China and result in improved rotor stabilities.

Forced Response in Axial Turbines Under the Influence of Partial Admission

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Jens Fridh ◽  
Björn Laumert ◽  
Torsten Fransson
Keyword(s):  
High Speed ◽  
Pressure Ratio ◽  
Forced Response ◽  
Rotor Blades ◽  
Response Analysis ◽  
Validation Data ◽  
Pressure Transducers ◽  
Control Stage ◽  
Engine Order ◽  
Partial Admission

High cycle fatigue (HCF) due to unforeseen excitation frequencies, underestimated force magnitudes, or a combination of both causes control-stage failures for steam turbine stakeholders. This paper provides an extended design criteria toolbox, as well as validation data, for control-stage design based on experimental data to reduce HCF incidents in partial-admission turbines. The upstream rotor in a two-stage air test turbine is instrumented with pressure transducers and strain gauges. Admission degrees extend from 28.6% to 100%, as one or two admission arcs are simulated by blocking segmental arcs immediately upstream of the first stator vanes with aerodynamically shaped filling blocks. Sweeps across a speed range of 50%–105% of design speed are performed at a constant turbine pressure ratio during simultaneous high-speed acquisition. A forced-response analysis is performed and results presented in Campbell diagrams. Partial admission creates a large number of low-engine-order forced responses because of the blockage, pumping, loading, and unloading processes. Combinations of the number of rotor blades and low-engine-order excitations are the principal sources of forced-response vibrations for the turbine studied here. Altering the stator and/or rotor pitches changes the excitation pattern. We observed that a relationship between the circumferential lengths of the admitted and nonadmitted arcs dictates the excitation forces and may serve as a design parameter.

Numerical and Experimental Investigation of Axial Gap Variation in High-Pressure Steam Turbine Stages

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Juri Bellucci ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Lorenzo Arcangeli ◽  
Nicola Maceli ◽  
...  
Keyword(s):  
High Pressure ◽  
Steam Turbine ◽  
Aerodynamic Performance ◽  
Operating Conditions ◽  
Performance Estimation ◽  
Flow Angle ◽  
High Pressure Steam ◽  
Aspect Ratios ◽  
Pressure Steam ◽  
The Impact

This work aims at investigating the impact of axial gap variation on aerodynamic performance of a high-pressure steam turbine stage. Numerical and experimental campaigns were conducted on a 1.5-stage of a reaction steam turbine. This low speed test rig was designed and operated in different operating conditions. Two different configurations were studied in which blades axial gap was varied in a range from 40% to 95% of the blade axial chord. Numerical analyses were carried out by means of three-dimensional, viscous, unsteady simulations, adopting measured inlet/outlet boundary conditions. Two sets of measurements were performed: steady measurements, from one hand, for global performance estimation of the whole turbine, such as efficiency, mass flow, and stage work; steady and unsteady measurements, on the other hand, were performed downstream of rotor row, in order to characterize the flow structures in this region. The fidelity of computational setup was proven by comparing numerical results to measurements. Main performance curves and spanwise distributions have shown a good agreement in terms of both shape of curves/distributions and absolute values. Moreover, the comparison of two-dimensional maps downstream of rotor row has shown similar structures of the flow field. Finally, a comprehensive study of the axial gap effect on stage aerodynamic performance was carried out for four blade spacings (10%, 25%, 40%, and 95% of S1 axial chord) and five aspect ratios (1.0, 1.6, 3, 4, and 5). The results pointed out how unsteady interaction between blade rows affects stage operation, in terms of pressure and flow angle distributions, as well as of secondary flows development. The combined effect of these aspects in determining the stage efficiency is investigated and discussed in detail.

Forced Response in Axial Turbines Under the Influence of Partial Admission

2012 ◽  
Author(s):  
Jens Fridh ◽  
Björn Laumert ◽  
Torsten Fransson
Keyword(s):  
High Speed ◽  
Pressure Ratio ◽  
Forced Response ◽  
Rotor Blades ◽  
Response Analysis ◽  
Validation Data ◽  
Pressure Transducers ◽  
Control Stage ◽  
Engine Order ◽  
Partial Admission

High cycle fatigue (HCF) due to unforeseen excitation frequencies or due to under predicted force magnitudes, or a combination of both causes control stage failures for steam turbine stakeholders. The objectives of this paper is to provide an extended design criteria toolbox and validation data for control stage design based on experimental data, with the aim to decrease HCF incidents for partial admission turbines. The upstream rotor in a two stage air test turbine is instrumented with pressure transducers and strain gauges. Admission degrees stretching from 28.6% to 100% as one or two admission arcs are simulated by blocking segmental arcs immediately upstream of first stator vanes by aerodynamically shaped filling blocks. Sweeps across a speed range from 50 to 105% of design speed are performed at constant turbine pressure ratio during simultaneous high speed acquisition. A forced response analysis is performed and results presented in Campbell diagrams. Partial admission creates a large number of low engine order forced responses because of the blockage, pumping, loading and unloading processes. Combinations of the number of rotor blades and low engine order excitations are the principal sources of forced response vibrations for the turbine studied herein. Altering the stator and/or rotor pitches will change the excitation pattern. A relation between the circumferential lengths of the admitted and non-admitted arcs that dictates the excitation forces is observed that may serve as a design parameter.

Investigations Into Aerodynamic Performance of Turbine Stages With Flexible Shroud Seals

2020 ◽  
Author(s):  
Xin Yan ◽  
Yabo Wang ◽  
Kang Zhang ◽  
Xinbo Dai ◽  
Kun He
Keyword(s):  
Steam Turbine ◽  
Flow Patterns ◽  
Aerodynamic Performance ◽  
Original Design ◽  
Flow Angle ◽  
Large Power ◽  
Aerodynamic Efficiency ◽  
Forward Bending ◽  
Outlet Flow ◽  
Reaction Degree

Abstract The present paper utilizes a numerical method to investigate the effect of flexible shroud seals, including the forward bending flexible seals and backward bending flexible seals, on aerodynamic performance of high pressure steam turbine stages. At first, the wear performance of flexible seal is analyzed with the Finite Element Analysis method. It shows that wear in flexible strip is so small that only the installation clearance needs to be considered in operation process. Then, by replacing the labyrinth shroud seals with flexible shroud seals, the aerodynamic efficiency, outlet flow angle distributions, and reaction degree distributions in two-stages are obtained. At three installation clearances, interactions between leakage flow and main flow, as well as the flow patterns in flexible shroud seals, are visualized and also compared with the original design case. The numerical results indicate that turbine stages configured with forward bending flexible shroud seals have a very close aerodynamic performance to those configured with conventional labyrinth shroud seals at the same clearance, whereas the turbine stages configured with backward bending flexible seals have lower total-total isentropic efficiency than those with conventional labyrinth shroud seals. By replacing the conventional labyrinth shroud seals with forward bending flexible shroud seals (at the same clearance), the aerodynamic efficiency, outlet flow angles, limiting streamlines, secondary flow patterns in shroud region and reaction degree distributions in stages are almost not affected. Since the forward bending flexible seal allows relatively smaller installation clearance than the conventional labyrinth seal, application of this kind of seal in rotor blade tip gap is much beneficial to achieve lower leakage rate and higher aerodynamic performance in large power steam turbine stages.

Sign in / Sign up

Export Citation Format

Share Document