Stress of Large Diameter Piping System Shoe Support

2017 ◽  
Author(s):  
Sadjad Ranjbaran ◽  
Akbar Daneshvar Ghalelar
Keyword(s):  
Failure Modes ◽  
Large Diameter ◽  
Estimation Method ◽  
Beam Theory ◽  
Local Stress ◽  
Accurate Estimation ◽  
Piping System ◽  
Element Analysis ◽  
Piping Systems ◽  
Applied Design

As codes and standards employ the beam theory to evaluate stress in piping systems, large diameter piping is therefore outside the domain of these codes and standards. To investigate any failure modes in these piping systems, more general codes such as ASME Sec. VIII Div.2 must be used. Research has shown that estimating local stress is important near the shoe support tip especially for large diameter piping systems and aboveground pipelines. To evaluate protection against local failure under an applied design load, a more accurate estimation method of ASME Sec. VIII Div.2, part 5 is applied by using elastic-plastic stress analysis procedures. For this purpose, finite element analysis is carried out along with distributed gravity loading and design pressure. Furthermore, parametric FEA studies are conducted on the effect of the ratio of pipe diameter to thickness, as well as the width and wrap angle of shoe support on the local stress of shoe support. The FEA results have been compared to semi-empirical formula for local stress in shoe support developed by AWWA standard.

Reduction in Stresses Shown in Piping Programs in Large Diameter Pipe Branch Connections by Applying Flexibilities Computed by Shell Finite Element Analysis

2004 ◽  
Author(s):  
Robert A. Robleto
Keyword(s):  
Finite Element Analysis ◽  
Large Diameter ◽  
Piping System ◽  
Bending Moments ◽  
Straight Pipe ◽  
Element Analysis ◽  
Large Diameter Pipe ◽  
Diameter Pipe ◽  
Piping Systems ◽  
Shell Finite Element

When designing branch connections in low pressure large diameter piping systems as in Figure 1, thicker is not always better. The flexibility factors in ASME B31.3 1 for branch connections do not assist the designer in taking credit for flexibility that may exist in a large diameter intersection. Since the stress intensification factors (SIFs) are relatively high for large diameter piping, many stub-in branch connections will require a pad to meet the code displacement stress limits. In an ASME B31.3 Piping analysis the stiffness of the branch connections is considered to be as stiff as a straight piece of pipe modeled as a beam. This is a simplifying assumption that can lead to expensive conservatism for the component and possibly non-conservatism for nearby equipment especially when large diameter pipe is considered. Branch connection flexibility is often negligible when compared with piping flexibility of straight pipe perpendicular to the deflection and bends which can ovalize under in-plane bending moments. However, studies at KBR show branch connections in large diameter pipe can contribute significant flexibility to a close coupled piping system.

Dealing With Heavy Loads in Large Diameter Piping

2012 ◽  
Author(s):  
Hector Rojas ◽  
Andrey Gutkovsky
Keyword(s):  
Large Diameter ◽  
Operating Conditions ◽  
Configuration Design ◽  
Piping System ◽  
Flow Conditions ◽  
Element Analysis ◽  
Piping Systems ◽  
Molten Sulfur ◽  
Heavy Loads

It is common in a refinery that some piping systems have to handle several flow conditions. However, when a new proposed condition implies the filling of an existing 68″ (1727 mm) line with molten Sulfur, which was initially designed for gas operation, a well thought engineering case study is required to guarantee that no damage will occur under the new operating conditions. This paper covers the procedures employed to qualify the integrity of a 68″ (1727 mm) piping system, initially designed to carry Sulfur vapors and required to handle occasional filling with molten Sulfur due to operational demands. The procedures of reviewing the initial configuration, design of modifications and reinforcements to the piping system and the use of Finite Element Analysis (FEA) in order to qualify several unique support configurations are explained in this paper.

Comparison of Failure Modes of Piping Systems With Wall Thinning Subjected to In-Plane, Out-of-Plane, and Mixed Mode Bending Under Seismic Load: An Experimental Approach

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Izumi Nakamura ◽  
Akihito Otani ◽  
Masaki Shiratori
Keyword(s):  
Dynamic Behavior ◽  
Failure Modes ◽  
Seismic Load ◽  
Piping System ◽  
Shake Table ◽  
Shake Table Tests ◽  
Wall Thinning ◽  
Piping Systems ◽  
Out Of Plane ◽  
Plane Bending

Pressurized piping systems used for an extended period may develop degradations such as wall thinning or cracks due to aging. It is important to estimate the effects of degradation on the dynamic behavior and to ascertain the failure modes and remaining strength of the piping systems with degradation through experiments and analyses to ensure the seismic safety of degraded piping systems under destructive seismic events. In order to investigate the influence of degradation on the dynamic behavior and failure modes of piping systems with local wall thinning, shake table tests using 3D piping system models were conducted. About 50% full circumferential wall thinning at elbows was considered in the test. Three types of models were used in the shake table tests. The difference of the models was the applied bending direction to the thinned-wall elbow. The bending direction considered in the tests was either of the in-plane bending, out-of-plane bending, or mixed bending of the in-plane and out-of-plane. These models were excited under the same input acceleration until failure occurred. Through these tests, the vibration characteristic and failure modes of the piping models with wall thinning under seismic load were obtained. The test results showed that the out-of-plane bending is not significant for a sound elbow, but should be considered for a thinned-wall elbow, because the life of the piping models with wall thinning subjected to out-of-plane bending may reduce significantly.

Creep Life Simulation and Assessment of High Temperature Piping Systems and Components

2012 ◽  
Author(s):  
Brian Rose ◽  
James Widrig
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Temperature ◽  
Creep Behavior ◽  
Material Behavior ◽  
Piping System ◽  
Remaining Life ◽  
Creep Life ◽  
Element Analysis ◽  
Piping Systems

High temperature piping systems and associated components, elbows and bellows in particular, are vulnerable to damage from creep. The creep behavior of the system is simulated using finite element analysis (FEA). Material behavior and damage is characterized using the MPC Omega law, which captures creep embrittlement. Elbow elements provide rapid yet accurate modeling of pinching of piping, which consumes a major portion of the creep life. The simulation is used to estimate the remaining life of the piping system, evaluate the adequacy of existing bellows and spring can supports and explore remediation options.

Comparison of Failure Modes of Piping Systems With Wall Thinning Subjected to In-Plane, Out-of-Plane and Mixed Mode Bending Under Seismic Load: Computational Approach

2007 ◽  
Author(s):  
Satoshi Tsunoi ◽  
Akira Mikami ◽  
Izumi Nakamura ◽  
Akihito Otani ◽  
Masaki Shiratori
Keyword(s):  
Analytical Model ◽  
Failure Modes ◽  
Experimental Investigations ◽  
Seismic Load ◽  
Piping System ◽  
Wall Thinning ◽  
Piping Systems ◽  
Out Of Plane ◽  
Seismic Loadings ◽  
Local Wall Thinning

The authors have proposed an analytical model by which they can simulate the dynamic and failure behaviors of piping systems with local wall thinning against seismic loadings. In the previous paper [13], the authors have carried out a series of experimental investigations about dynamic and failure behaviors of the piping system with fully circumferential 50% wall thinning at an elbow or two elbows. In this paper these experiments have been simulated by using the above proposed analytical model and investigated to what extent they can catch the experimental behaviors by simulations.

Comparison of Failure Modes of Piping Systems With Wall Thinning Subjected to In-Plane, Out-of-Plane and Mixed Mode Bending Under Seismic Load: An Experimental Approach

2007 ◽  
Author(s):  
Izumi Nakamura ◽  
Akihito Otani ◽  
Masaki Shiratori
Keyword(s):  
Failure Modes ◽  
Seismic Load ◽  
Piping System ◽  
Shake Table ◽  
Shake Table Tests ◽  
Wall Thinning ◽  
Piping Systems ◽  
Out Of Plane ◽  
Plane Bending ◽  
The Difference

In order to investigate the influence of degradation on the dynamic behavior and failure modes of piping systems with local wall thinning, shake table tests using 3-D piping system models were conducted. About 50% full circumferential wall thinning at elbows was considered in the test. Three types of models were used in the shake table tests. The difference of the models was the applied bending direction to the thinned wall elbow. The bending direction considered in the tests was either of the in-plane bending, out-of-plane bending, or mixed bending of the in-plane and out-of-plane. These models were excited under the same input acceleration until failure occurred. Through these tests, the vibration characteristic and failure modes of piping models with wall thinning under seismic load were obtained. The test results showed that the out-of-plane bending is not significant for a sound elbow, but should be considered for a thinned wall elbow, because the life of piping models with wall thinning subjected to out-of-plane bending may reduce significantly.

Experimental studies of a typical sprinkler piping system in hospitals

2016 ◽  
Vol 49 (1) ◽  
pp. 1-12
Author(s):  
Zhen-Yu Lin ◽  
Fan-Ru Lin ◽  
Juin-Fu Chai ◽  
Kuo-Chun Chang
Keyword(s):  
Failure Modes ◽  
Experimental Studies ◽  
Hysteresis Loops ◽  
Research Programme ◽  
Shaking Table ◽  
Piping System ◽  
Improvement Strategy ◽  
Flexible Pipes ◽  
Piping Systems ◽  
Cyclic Loading Tests

Based on the issue of life safety and immediate needs of emergency medical services provided by hospitals after strong earthquakes, this paper aims to introduce a research programme on assessment and improvement strategies for a typical configuration of sprinkler piping systems in hospitals. The study involved component tests and subsystem tests. Cyclic loading tests were conducted to investigate the inelastic behaviour of components including concrete anchorages, screwed fittings of small-bore pipes and couplings. Parts of a horizontal piping system of a seismic damaged sprinkler piping system were tested using shaking table tests. Furthermore, horizontal piping subsystems with seismic resistant devices such as braces, flexible pipes and couplings were also tested. The test results showed that the main cause of damage was the poor capacity of a screwed fitting of the small-bore tee branch. The optimum improvement strategy to achieve a higher nonstructural performance level for the horizontal piping subsystem is to strengthen the main pipe with braces and decrease moment demands on the tee branch by the use of flexible pipes. The hysteresis loops and failure modes of components were further discussed and will be used to conduct numerical analysis of sprinkler piping systems in future studies.

scholarly journals Nonlinear Seismic Correlation Analysis of the JNES/NUPEC Large-Scale Piping System Tests

2008 ◽  
Author(s):  
Jinsuo Nie ◽  
Giuliano DeGrassi ◽  
Charles H. Hofmayer ◽  
Syed A. Ali
Keyword(s):  
Correlation Analysis ◽  
Test Data ◽  
Nuclear Power ◽  
Large Scale ◽  
Failure Modes ◽  
Plastic Behavior ◽  
Piping System ◽  
Highly Nonlinear ◽  
Piping Systems ◽  
The U.S

The Japan Nuclear Energy Safety Organization/Nuclear Power Engineering Corporation (JNES/NUPEC) large-scale piping test program has provided valuable new test data on high level seismic elasto-plastic behavior and failure modes for typical nuclear power plant piping systems. The component and piping system tests demonstrated the strain ratcheting behavior that is expected to occur when a pressurized pipe is subjected to cyclic seismic loading. Under a collaboration agreement between the U.S. and Japan on seismic issues, the U.S. Nuclear Regulatory Commission (NRC)/ Brookhaven National Laboratory (BNL) performed a correlation analysis of the large-scale piping system tests using detailed state-of-the-art nonlinear finite element models. Techniques are introduced to develop material models that can closely match the test data. The shaking table motions are examined. The analytical results are assessed in terms of the overall system responses and the strain ratcheting behavior at an elbow. The paper concludes with the insights about the accuracy of the analytical methods for use in performance assessments of highly nonlinear piping systems under large seismic motions.

Effects of High Frequency Hydrodynamic Loads on Structural Integrity and Mechanical Operability of Valves

2015 ◽  
Author(s):  
Yigit Isbiliroglu ◽  
Cagri Ozgur ◽  
Evren Ulku ◽  
Nish Vaidya ◽  
Kristofor Paserba
Keyword(s):  
High Frequency ◽  
Structural Integrity ◽  
Energy Content ◽  
Hybrid Approach ◽  
Piping System ◽  
Seismic Loads ◽  
Damage Potential ◽  
Element Analysis ◽  
Piping Systems ◽  
Number Of Cycles

In-line valves are qualified for static as well as dynamic loads from seismic and hydrodynamic (HD) events. Seismic loads are generally characterized by frequency content less than about 33 Hz whereas HD loads may exhibit a broad range of frequencies greater than 33 Hz. HD loads may also result in spectral accelerations significantly in excess of those due to the design basis seismic events. Current regulatory guidelines do not specifically address the evaluation of equipment response to high frequency loading. This paper investigates the response of skid and line mounted valves of piping systems under HD loads by using several independent rigorous finite element analysis solutions for various piping system segments. It presents a hybrid approach for the evaluation of the response of valves to HD and seismic loads. The proposed approach significantly reduces the amount of individual analysis and testing needed to qualify the valves. First, valve responses are evaluated on the basis of displacements since HD loads are generally characterized by high frequencies and small durations. Second, the damage potential of the loads on the valve actuators is represented by the energy imparted to the actuator quantified in terms of Arias intensity. The rationale for using the energy content is based on the fact that damage due to dynamic loading is related not only to the amplitude of the acceleration response but also to the duration and the number of cycles over which this acceleration is imposed.

Improvement of the Damping Constants for Seismic Design of Piping System for NPP

2002 ◽  
Author(s):  
Kei Kobayashi ◽  
Takashi Satoh ◽  
Nobuyuki Kojima ◽  
Kiyoshi Hattori ◽  
Masaki Nakagawa ◽  
...  
Keyword(s):  
Power Plant ◽  
Seismic Design ◽  
Nuclear Power ◽  
Power Plants ◽  
Estimation Method ◽  
Piping System ◽  
Piping Systems ◽  
Support Element ◽  
Present Design ◽  
Bolt Support

The present design damping constants for nuclear power plant (NPP)’s piping system in Japan were developed through discussion among expert researchers, electric utilities and power plant manufactures. They are standardized in “Technical guidelines for seismic design of Nuclear Power Plants” (JEAG 4601-1991 Supplemental Edition). But some of the damping constants are too conservative because of a lack of experimental data. To improve this excessive conservatism, piping systems supported by U-bolts were chosen and U-bolt support element test and piping model excitation test were performed to obtain proper damping constants. The damping mechanism consists of damping due to piping materials, damping due to fluid interaction, damping due to plastic deformation of piping and supports, and damping due to friction and collision between piping and supports. Because the damping due to friction and collision was considered to be dominant, we focused our effort on formulating these phenomena by a physical model. The validity of damping estimation method was confirmed by comparing data that was obtained from the elemental tests and the actual scale piping model test. New design damping constants were decided from the damping estimations for piping systems in an actual plant. From now on, we will use the new design damping constants for U-bolt support piping systems, which were proposed from this study, as a standard in the Japanese piping seismic design.

Sign in / Sign up

Export Citation Format

Share Document