Coupled Pump and Pipe System Analysis for Optimum Design of District Heating System

2017 ◽  
Author(s):  
Magnus Thor Jonsson ◽  
Lilja Magnusdottir
Keyword(s):  
Objective Function ◽  
System Analysis ◽  
District Heating ◽  
Heating System ◽  
System Optimization ◽  
Operational Cost ◽  
District Heating System ◽  
Pipe System ◽  
Pump Station ◽  
Optimization Parameters

This paper describes a novel approach for optimizing a district heating distribution network under various flow rate conditions. For district heating systems, the demand or the flow and pressure at each node varies over the time of year. The flow control that affects the operational cost can be based on the variable speed and the on/off control on serial pumping or pressure controlled valves. In the pipe system design, the topology, or the pipe layout, and the pipe diameter is optimized using genetic algorithms. Standardized methods are used for calculating the pipe thickness, supports, anchors and the thermal expansion loops. The interconnection between the pipe system and the pump station design is discussed. The objective is to minimize the total or life cycle cost (capital maintenance and operational cost), subject to ensuring demands or constraints at all points. The results are compared to classical methods where the pump station and the pipe system are designed separately and the improvements are discussed. The problem is formulated by developing an objective function where the optimization parameters define the pump arrangement, pipe system topology, and pipe diameters. The pump station and pipe system optimization consist of selecting components from a pre-defined set of elements and is implemented with discrete decision variables. Optimization of pipe elements consists of optimizing the diameter, after the topology has been defined, and is implemented with discrete variables. Flow distribution and pressure analysis is performed. Thicknesses, pressure classes, supports, expansion loops and anchors are not part of the optimization parameters, but are determined during the evaluation of the objective function. Each time the objective function is evaluated, the pipe system is designed in a sub-optimization according to given loads. The pressure head constraints are used to design the pumping curves. The method is tested on a district heating system in Reykjavik, Iceland.

scholarly journals District heating system simulation considering consumer and pump operation features

Vestnik MGSU ◽  
2019 ◽  
pp. 748-755 ◽  
Author(s):  
Saule K. Abildinova ◽  
Stanislav V. Chicherin
Keyword(s):  
Mathematical Model ◽  
Energy Consumption ◽  
District Heating ◽  
Heating System ◽  
Hot Water ◽  
Water Supply Systems ◽  
Problem Solution ◽  
District Heating System ◽  
Pump Station ◽  
Pump Equipment

Introduction. The purpose of this investigation is to show what changes introduced in the mathematical model of a district heating system are capable of considerable improving the convergence of simulation results and actual data. The study evaluates the work of heating supply establishments with their customers as well as analysis of the ways of enhancing pump equipment efficiency that allows saving electric energy or increasing output at the same energy consumption. Materials and methods. Engineering acceptance of newly introduced and reconstructed facilities is conducted, heat loads are corrected, disconnections and recurrent connections of indebted consumers are carried out. Studying data submitted by a local heat supply establishment shows that pump seals made from iron and steel are subject accelerated wear in the course of operation. Results. Three variants of the problem solution are suggested: making seals from bronze or stainless steel, prevention of unjustified increase of seal clearances as well as using labyrinth pump seals. This will allow increasing pump equipment efficiency by 5 to 7 % and save about 2 × 105 kW∙h of electrical energy for every pump or increase of output at the same energy consumption. Taking into account that a pump station is a part of the district heating system and unmachined inner surfaces of the pumps have a significant roughness, grinding of these surfaces can improve their hydraulic characteristics of the pumps. In the scope of the suggested method, the entire district heating system is considered not in the situation when actual load is equal to the sum of all the design loads and the pump equipment has manufacturer’s parameters, but accounting actual loads and characteristics. Conclusions. Mathematical model of district heating system heating and hydraulic mode that takes issues mentioned above into consideration would allow simulating joint operation of the heating and hot water supply systems at transient operation modes with higher accuracy.

Optimization of a Local District Heating Plant Under Fuel Flexibility and Performance

2011 ◽  
Author(s):  
Souman Rudra ◽  
Lasse Rossendahl ◽  
Niels From
Keyword(s):  
Natural Gas ◽  
Fossil Fuels ◽  
System Analysis ◽  
Reference Model ◽  
District Heating ◽  
Heating System ◽  
Energy System ◽  
District Heating System ◽  
And Performance ◽  
Heating Plant

Brovst is a small district in Denmark. Based on the case of Brovst, this paper analyses the role of district heating in future Renewable Energy Systems. The present use of fossil fuels in the Brovst DHP (district heating plant) represents an increasing environmental and climate-related load. So, an investigation has been made to reduce the use of fossil fuels for district heating system and make use of the local renewable resources (Biogas, Solar and Geothermal) for district heating purpose. In this article, the techno-economic assessment is achieved through the development of a suite of models that are combined to give cost and performance data for this district heating system. Different local fuels have been analyzed for different perspectives to find the way to optimize the whole integrated system in accordance with fuel availability and cost. This paper represents the energy system analysis mode energyPRO which has been used to analyses the integration of large scale energy system into the domestic district heating system. A model of the current work on the basis of information from the plant (using fossil fuel) is established and named as a reference model. Then different solutions are calculated for various local fuels in energyPRO. A comparison has been made between the reference model and the basis for individual solutions. The greatest reduction in heat price is obtained by replacing one engine with a new biogas where heat production is divided by 66% of biogas, 13% natural gas engines and 21% natural gas boilers.

scholarly journals Technology Pathways and Economic Analysis for Transforming High Temperature to Low Temperature District Heating Systems

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3218
Author(s):  
Pedro Durán ◽  
Herena Torio ◽  
Patrik Schönfeldt ◽  
Peter Klement ◽  
Benedikt Hanke ◽  
...  
Keyword(s):  
Sensitivity Analysis ◽  
Renewable Energy ◽  
High Temperature ◽  
Low Temperature ◽  
Economic Analysis ◽  
District Heating ◽  
Heating System ◽  
District Heating System ◽  
Heating Systems ◽  
District Heating Systems

There are 1454 district heating systems in Germany. Most of them are fossil based and with high temperature levels, which is neither efficient nor sustainable and needs to be changed for reaching the 2050 climate goals. In this paper, we present a case study for transforming a high to low temperature district heating system which is more suitable for renewable energy supply. With the Carnot Toolbox, a dynamic model of a potential district heating system is simulated and then transformed to a low temperature supply. A sensitivity analysis is carried out to see the system performance in case space constrains restrict the transformation. Finally, an economic comparison is performed. Results show that it is technically possible to perform the transformation until a very low temperature system. The use of decentralized renewable sources, decentralized heat storage tanks and the placement of a heat pump on each building are the key points to achieve the transformation. Regarding the sensitivity analysis, the transformation is worth doing until the seasonal storage and solar collector field sizes are reduced to 60% and 80% of their values in the reference case, respectively. The economic analysis shows, however, that it is hard for highly efficient low temperature renewable based heat networks to compete with district heating systems based on a centralized fossile CHP solution. Thus, though the presented transformation is technically possible, there is a strong need to change existing economic schemes and policies for fostering a stronger promotion of renewable energy policies in the heat sector.

Predicting Hourly Heating Load in a District Heating System Based on a Hybrid CNN-LSTM Model

2021 ◽  
pp. 110998
Author(s):  
Jiancai Song ◽  
Liyi Zhang ◽  
Guixiang Xue ◽  
YunPeng Ma ◽  
Shan Gao ◽  
...  
Keyword(s):  
District Heating ◽  
Heating System ◽  
District Heating System ◽  
Heating Load

scholarly journals Upgrading a District Heating System by Means of the Integration of Modular Heat Pumps, Geothermal Waters, and PVs for Resilient and Sustainable Urban Energy

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2347
Author(s):  
Elżbieta Hałaj ◽  
Jarosław Kotyza ◽  
Marek Hajto ◽  
Grzegorz Pełka ◽  
Wojciech Luboń ◽  
...  
Keyword(s):  
District Heating ◽  
Heating System ◽  
Upper Jurassic ◽  
Heat Pumps ◽  
Water Levels ◽  
Energy Potential ◽  
Geothermal Waters ◽  
District Heating System ◽  
Heating And Cooling ◽  
The City

Krakow has an extensive district heating network, which is approximately 900 km long. It is the second largest city in terms of the number of inhabitants in Poland, resulting in a high demand for energy—for both heating and cooling. The district heating of the city is based on coal. The paper presents the conception of using the available renewable sources to integrate them into the city’s heating system, increasing the flexibility of the system and its decentralization. An innovative solution of the use of hybrid, modular heat pumps with power dependent on the needs of customers in a given location and combining them with geothermal waters and photovoltaics is presented. The potential of deep geothermal waters is based on two reservoirs built of carbonate rocks, namely Devonian and Upper Jurassic, which mainly consist of dolomite and limestone. The theoretical potential of water intake equal to the nominal heating capacity of a geothermal installation is estimated at 3.3 and 2.0 MW, respectively. Shallow geothermal energy potential varies within the city, reflecting the complex geological structure of the city. Apart from typical borehole heat exchangers (BHEs), the shallower water levels may represent a significant potential source for both heating and cooling by means of water heat pumps. For the heating network, it has been proposed to use modular heat pumps with hybrid sources, which will allow for the flexible development of the network in places previously unavailable or unprofitable. In the case of balancing production and demand, a photovoltaic installation can be an effective and sufficient source of electricity that will cover the annual electricity demand generated by the heat pump installation, when it is used for both heating and cooling. The alternating demand of facilities for heating and cooling energy, caused by changes in the seasons, suggests potential for using seasonal cold and heat storage.

scholarly journals Overview of Solutions for the Low-Temperature Operation of Domestic Hot-Water Systems with a Circulation Loop

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3350
Author(s):  
Theofanis Benakopoulos ◽  
William Vergo ◽  
Michele Tunzi ◽  
Robbe Salenbien ◽  
Svend Svendsen
Keyword(s):  
Low Temperature ◽  
Heat Loss ◽  
District Heating ◽  
Heating System ◽  
Hot Water ◽  
Heating Power ◽  
Circulation Loop ◽  
Space Heating ◽  
District Heating System ◽  
Domestic Hot Water

The operation of typical domestic hot water (DHW) systems with a storage tank and circulation loop, according to the regulations for hygiene and comfort, results in a significant heat demand at high operating temperatures that leads to high return temperatures to the district heating system. This article presents the potential for the low-temperature operation of new DHW solutions based on energy balance calculations and some tests in real buildings. The main results are three recommended solutions depending on combinations of the following three criteria: district heating supply temperature, relative circulation heat loss due to the use of hot water, and the existence of a low-temperature space heating system. The first solution, based on a heating power limitation in DHW tanks, with a safety functionality, may secure the required DHW temperature at all times, resulting in the limited heating power of the tank, extended reheating periods, and a DH return temperature of below 30 °C. The second solution, based on the redirection of the return flow from the DHW system to the low-temperature space heating system, can cool the return temperature to the level of the space heating system return temperature below 35 °C. The third solution, based on the use of a micro-booster heat pump system, can deliver circulation heat loss and result in a low return temperature below 35 °C. These solutions can help in the transition to low-temperature district heating.

Sign in / Sign up

Export Citation Format

Share Document