Determination of the critical system and data processing parameters for Raman-DIAL O3 and H2O measurements: numerical simulation

1999 ◽  
Author(s):  
Max Frioud ◽  
Valentin Mitev ◽  
Renaud Matthey
Keyword(s):  
Numerical Simulation ◽  
Data Processing ◽  
Processing Parameters ◽  
Critical System

scholarly journals Optimal design of the solar tracking system of parabolic trough concentrating collectors

2020 ◽  
Vol 15 (4) ◽  
pp. 613-619
Author(s):  
Li Kong ◽  
Yunpeng Zhang ◽  
Zhijian Lin ◽  
Zhongzhu Qiu ◽  
Chunying Li ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Solar Radiation ◽  
Tracking System ◽  
Low Cost ◽  
Parabolic Trough ◽  
The North ◽  
Tracking Mode ◽  
Solar Tracking ◽  
East West

Abstract The present work aimed to select the optimum solar tracking mode for parabolic trough concentrating collectors using numerical simulation. The current work involved: (1) the calculation of daily solar radiation on the Earth’s surface, (2) the comparison of annual direct solar radiation received under different tracking modes and (3) the determination of optimum tilt angle for the north-south tilt tracking mode. It was found that the order of solar radiation received in Shanghai under the available tracking modes was: dual-axis tracking > north-south Earth’s axis tracking > north-south tilt tracking (β = 15°) > north-south tilt tracking (β = 45) > north-south horizontal tracking > east-west horizontal tracking. Single-axis solar tracking modes feature simple structures and low cost. This study also found that the solar radiation received under the north-south tilt tracking mode was higher than that of the north-south Earth’s axis tracking mode in 7 out of 12 months. Therefore, the north-south tilt tracking mode was studied separately to determine the corresponding optimum tilt angles in Haikou, Lhasa, Shanghai, Beijing and Hohhot, respectively, which were shown as follows: 18.81°, 27.29°, 28.67°, 36.21° and 37.97°.

Determination of optimal microwave curing cycle for fly ash mortars

2008 ◽  
Vol 35 (4) ◽  
pp. 349-357 ◽  
Author(s):  
İlker Bekir Topçu ◽  
Mehmet Uğur Toprak ◽  
Devrim Akdağ
Keyword(s):  
Fly Ash ◽  
Processing Parameters ◽  
Microwave Energy ◽  
Strength Prediction ◽  
Strength Development ◽  
Microwave Curing ◽  
Optimal Processing ◽  
Cement Mortars ◽  
Curing Cycle

Microwave energy can accelerate the hydration of cement, which results in the rapid strength development of concrete. In this paper, prediction of later age compressive strength of fly ash cement mortars, based on the accelerated strength of mortars cured with microwave energy, was investigated. To accelerate curing properly, optimal processing parameters of microwave curing (MC) on Portland cement mortars (CM) and fly ash cement mortars (FA) were first determined and then were applied to mortars. The possible early ages for the strength prediction were found to be at 6 and 8 h for CM and FA, respectively. The error percentages for prediction of CM were ±2.22% and 2.91% for 7 and 28 d, respectively. Error percentages for FA, on the other hand, were ±4.36% and 5.20% for 7 and 28 d, respectively.

DIGITAL ZENITH CAMERA FOR VERTICAL DEFLECTION DETERMINATION

2012 ◽  
Vol 38 (4) ◽  
pp. 123-129 ◽  
Author(s):  
Māris Abele ◽  
Jānis Balodis ◽  
Inese Janpaule ◽  
Ieva Lasmane ◽  
Augusts Rubans ◽  
...  
Keyword(s):  
Data Processing ◽  
Digital Imaging ◽  
High Accuracy ◽  
Reference Star ◽  
Research Groups ◽  
Vertical Deflection ◽  
Digital Imaging Technology ◽  
Prototype Instrument ◽  
Automated Determination

Recent accomplishments in advancement of accurate astrometric reference star catalogues, development of digital imaging technology, high accuracy tiltmeter technology, and geocentric coordinate availability provided by GNSS, have made possible accurate, fast and automated determination of vertical deflections using astrometric methods. Zenith cameras for this kind of measurements have been developed or are being developed by several research groups. The paper describes a research project by Institute of Geodesy and Geoinformation, intended to design a portable digital zenith camera for vertical deflection determination with 0.1” expected accuracy. Camera components are described, proposed data processing algorithm and preliminary results, obtained with prototype instrument, are presented.

The PPP data processing algorithm to create geodetic networks

2021 ◽  
pp. 464-468
Author(s):  
A.D. Tikhonov ◽  
A.A. Kochiev
Keyword(s):  
Data Processing ◽  
Processing Algorithm ◽  
Navigation Systems ◽  
Geodetic Networks ◽  
Data Processing Algorithm ◽  
Global Navigation ◽  
Global Navigation Systems

The article deals with determination of coordinates using global navigation systems, and application of the PPP data processing algorithm to obtain coordinates. The authors conducted an experiment illustrating the algorithm accuracy.

scholarly journals Determination of Long Horizontal Borehole Height in Roofs and its Application to Gas Drainage

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2647
Author(s):  
Gang Wang ◽  
Cheng Fan ◽  
Hao Xu ◽  
Xuelin Liu ◽  
Rui Wang
Keyword(s):  
Numerical Simulation ◽  
Theoretical Model ◽  
Fracture Zone ◽  
Coalbed Methane ◽  
High Efficiency ◽  
Gas Drainage ◽  
Methane Drainage ◽  
Working Face ◽  
Variation Characteristics

Accurately determining the height of the gas-guiding fracture zone in the overlying strata of the goaf is the key to find the height of the long horizontal borehole in the roof. In order to determine the height, in this study we chose the 6306 working face of Tangkou Coal Mine in China as a research example and used both the theoretical model and discrete element method (DEM) numerical simulation to find the height of the gas-guiding fracture zone and applied the height to drill a long horizontal borehole in the roof of the 6303 working face. Furthermore, the borehole was utilized to deep into the roof for coalbed methane drainage and the results were compared with conventional gas drainage measures from other aspects. The height of the gas-guiding fracture zone was found to be 48.57 m in theoretical model based on the bulk coefficient and the void ratio and to be 51.19 m in the DEM numerical simulation according to the temporal and spatial variation characteristics of porosity. Taking both the results of theoretical analysis and numerical simulation into consideration, we determined that gas-guiding fracture zone is 49.88 m high and applied it to drill a long horizontal borehole deep into the roof in the 6303 working face field. Compared with conventional gas drainage measures, we found that the long horizontal borehole has the high stability, high efficiency and strong adaptability for methane drainage.

Sign in / Sign up

Export Citation Format

Share Document