Piezoelectric transducer with displacement amplifier

1993 ◽  
Vol 93 (1) ◽  
pp. 595-595
Author(s):  
Steven G. Petermann
Keyword(s):  
Piezoelectric Transducer

Analysis of AC-DC Converter Circuit Performance with Difference Piezoelectric Transducer Array Connection

2020 ◽  
Vol 12 (7) ◽  
Author(s):  
Nik Ahmad Zainal Abidin ◽  
◽  
Norkharziana Mohd Nayan ◽  
Azuwa Ali ◽  
N. A. Azli ◽  
...  
Keyword(s):  
Piezoelectric Transducer ◽  
Simulation Analysis ◽  
Piezoelectric Sensor ◽  
Transducer Array ◽  
Circuit Performance ◽  
Array Configuration ◽  
Full Wave ◽  
Bridge Rectifier ◽  
In Series ◽  
Parallel Voltage

This research presents a simulation analysis for the AC-DC converter circuit with a different configurations of the array connection of the piezoelectric sensor. The selection of AC-DC converter circuits is full wave bridge rectifier (FWBR), parallel SSHI (P-SSHI) and parallel voltage multiplier (PVM) with array configuration variation in series (S), parallel (P), series-parallel (SP) and parallel-series (PS). The system optimizes with different load configurations ranging from 10 kΩ to 1 MΩ. The best configuration of AC-DC converter with an appropriate array piezoelectric connection producing the optimum output of harvested power is presented. According to the simulation results, the harvested power produced by using P-SSHI converter connected with 3 parallel piezoelectric transducer array was 85.9% higher than for PVM and 15.88% higher than FWBR.

scholarly journals Tilt Active Vibration Isolation Using Vertical Pendulum and Piezoelectric Transducer with Parallel Controller

2021 ◽  
Vol 11 (10) ◽  
pp. 4526
Author(s):  
Lihua Wu ◽  
Yu Huang ◽  
Dequan Li
Keyword(s):  
Piezoelectric Transducer ◽  
Vibration Isolation ◽  
Vertical Vibration ◽  
Open Loop ◽  
Negative Effects ◽  
Voltage Controller ◽  
Hysteresis Nonlinearity ◽  
Passive Vibration Isolation ◽  
Active Vibration ◽  
Active Vibration Isolation

Tilt vibrations inevitably have negative effects on some precise engineering even after applying horizontal and vertical vibration isolations. It is difficult to adopt a traditional passive vibration isolation (PVI) scheme to realize tilt vibration isolation. In this paper, we present and develop a tilt active vibration isolation (AVI) device using a vertical pendulum (VP) tiltmeter and a piezoelectric transducer (PZT). The potential resolution of the VP is dependent on the mechanical thermal noise in the frequency bandwidth of about 0.0265 nrad, which need not be considered because it is far below the ground tilt of the laboratory. The tilt sensitivity of the device in an open-loop mode, investigated experimentally using a voltage controller, is found to be (1.63±0.11)×105 V/rad. To compensate for the hysteresis nonlinearity of the PZT, we experimentally established the multi-loop mathematical model of hysteresis, and designed a parallel controller consisting of both a hysteresis inverse model predictor and a digital proportional–integral–differential (PID) adjuster. Finally, the response of the device working in close-loop mode to the tilt vibration was tested experimentally, and the tilt AVI device showed a good vibration isolation performance, which can remarkably reduce the tilt vibration, for example, from 6.0131 μrad to below 0.0103 μrad.

scholarly journals Design Study of a Round Window Piezoelectric Transducer for Active Middle Ear Implants

Sensors ◽  
2021 ◽  
Vol 21 (3) ◽  
pp. 946
Author(s):  
Dong Ho Shin
Keyword(s):  
Hearing Loss ◽  
Sensorineural Hearing Loss ◽  
Middle Ear ◽  
Piezoelectric Transducer ◽  
Round Window ◽  
Piezoelectric Element ◽  
Sensorineural Hearing ◽  
Flat Band ◽  
Middle Ear Implants ◽  
Output Characteristics

This report describes the design of a new piezoelectric transducer for round window (RW)-driven middle ear implants. The transducer consists of a piezoelectric element, gold-coated copper bellows, silicone elastomer (polydimethylsiloxane, PDMS), metal cylinder (tungsten), and titanium housing. The piezoelectric element is fixed to the titanium housing and mechanical resonance is generated by the interaction of the bellows, PDMS, and tungsten cylinder. The dimensions of PDMS and the tungsten cylinder with output characteristics suitable for compensation of sensorineural hearing loss were derived by mechanical vibrational analysis (equivalent mechanical model and finite element analysis (FEA)). Based on the results of FEA, the RW piezoelectric transducer was implemented, and bench tests were performed under no-load conditions to confirm the output characteristics. The transducer generates an average displacement of 219.6 nm in the flat band (0.1–1 kHz); the resonance frequency is 2.3 kHz. To evaluate the output characteristics, the response was compared to that of an earlier transducer. When driven by the same voltage (6 Vp), the flat band displacement averaged 30 nm larger than that of the other transducer, and no anti-resonance was noted. Therefore, we expect that the new transducer can serve as an output device for hearing aids, and that it will improve speech recognition and treat high-frequency sensorineural hearing loss more effectively.

Low‐frequency piezoelectric‐transducer applications of ZnO film

1974 ◽  
Vol 25 (1) ◽  
pp. 10-11 ◽  
Author(s):  
Tadashi Shiosaki ◽  
Akira Kawabata
Keyword(s):  
Piezoelectric Transducer ◽  
Low Frequency ◽  
Zno Film

Dynamic Characteristics of a Piezoelectric Transducer with Structural Damping

2013 ◽  
Vol 198 ◽  
pp. 633-638 ◽  
Author(s):  
Marek Płaczek
Keyword(s):  
Piezoelectric Transducer ◽  
Piezoelectric Materials ◽  
Research Centre ◽  
Structural Damping ◽  
Mechatronic Systems ◽  
Mathematical Algorithm ◽  
Analysis And Synthesis ◽  
The Matrix ◽  
Piezoelectric Stacks ◽  
Future Work

Work presents a proposal of an analysis method of the piezoelectric transducer. The considered system is a longitudinally vibrating single PZT plate. The main aim of this work is to designate characteristics of the considered PZT plate. Using constitutive equations of piezoelectric materials and an equation of the plates motion a matrix of characteristics of the system was obtained. Relations between mechanical and electrical parameters (forces, displacements, electric current and voltage) that describe behaviour of the system are included in the matrix of characteristics. A dynamic flexibility relation between the plates deformation and a force applied to the system is considered. A structural damping of the plates material was being taken into consideration and its influence on the plates dynamic flexibility is analysed. This work is an introduction to a task of analysis of complex systems. In future work the developed model and proposed mathematical algorithm will be used to analyse piezoelectric stacks. Non-classical methods will be used. It is a part of research works of Gliwice research centre related with an analysis and synthesis of mechanical and mechatronic systems [4-7,9,10,16-18]. Passive and active mechanical and mechatronic systems with piezoelectric transducers were analysed [1-3]. Works were also supported by computer-aided methods [8]. Both classical and non-classical methods were being considered. The discussed subject is important due to increasing number of applications of both simple and reverse piezoelectric phenomena in various modern technical devices.

Model of a pvdf piezoelectric transducer for use in biomedical studies

1980 ◽  
Vol 24 (1) ◽  
pp. 289-292 ◽  
Author(s):  
Sidney B. Lang ◽  
Bruce D. Sollish ◽  
Motti Moshitzky ◽  
Ephraim H. Frei
Keyword(s):  
Piezoelectric Transducer
Sign in / Sign up

Export Citation Format

Share Document