Numerical investigation on the effect of bluntness factor on scouring mechanism by using lenticular geometry piers

2020 ◽  
Vol 47 (3) ◽  
pp. 279-290
Author(s):  
Yousef Hassanzadeh ◽  
Milad Khosravi ◽  
Nazila Kardan
Keyword(s):  
Flow Field ◽  
Large Eddy Simulation ◽  
Flow Separation ◽  
Width Ratio ◽  
Scour Depth ◽  
Clear Water ◽  
Eddy Simulation ◽  
Water State ◽  
Large Eddy ◽  
Scouring Process

Local scour and flow field around cylinders with lenticular geometry and different bluntness factors under the clear-water state were investigated numerically. To examine the scouring, large eddy simulation with a WMLES-Omega sub-grid model incorporating the sediment transport and morphodynamic model was applied. Streamlined geometry of the pier significantly affected the scour pattern and flow field in the lenticular model with length to width ratio of 5 and bluntness factor of zero. In the mentioned case, a very small scoured region was estimated at the sides of the pier, so it can be concluded that scour depth and scoured region decreases as the length to width ratio increases. Investigation of the scouring process and the flow field revealed that, the flow separation can affect the scour mechanism more in comparison to down-flow.

Large Eddy Simulation of Flow and Heat Transfer Mechanism in Matrix Cooling Channel

2017 ◽  
Author(s):  
Yigang Luan ◽  
Lianfeng Yang ◽  
Bo Wan ◽  
Tao Sun
Keyword(s):  
Heat Transfer ◽  
Flow Field ◽  
Large Eddy Simulation ◽  
Gas Turbine ◽  
Transfer Mechanism ◽  
Heat Transfer Mechanism ◽  
Longitudinal Vortices ◽  
Eddy Simulation ◽  
Flow And Heat Transfer ◽  
Large Eddy

Gas turbine engines have been widely used in modern industry especially in the aviation, marine and energy fields. The efficiency of gas turbines directly affects the economy and emissions. It’s acknowledged that the higher turbine inlet temperatures contribute to the overall gas turbine engine efficiency. Since the components are subject to the heat load, the internal cooling technology of turbine blades is of vital importance to ensure the safe and normal operation. This paper is focused on exploring the flow and heat transfer mechanism in matrix cooling channels. In order to analyze the internal flow field characteristics of this cooling configuration at a Reynolds number of 30000 accurately, large eddy simulation method is carried out. Methods of vortex identification and field synergy are employed to study its flow field. Cross-sectional views of velocity in three subchannels at different positions have been presented. The results show that the airflow is strongly disturbed by the bending part. It’s concluded that due to the bending structure, the airflow becomes complex and disordered. When the airflow goes from the inlet to the turning, some small-sized and discontinuous vortices are formed. Behind the bending structure, the size of the vortices becomes big and the vortices fill the subchannels. Because of the structure of latticework, the airflow is affected by each other. Airflow in one subchannel can exert a shear force on another airflow in the opposite subchannel. It’s the force whose direction is the same as the vortex that enhances the longitudinal vortices. And the longitudinal vortices contribute to the energy exchange of the internal airflow and the heat transfer between airflow and walls. Besides, a comparison of the CFD results and the experimental data is made to prove that the numerical simulation methods are reasonable and acceptable.

scholarly journals Investigation of the velocity field downstream of a benchmark vent using numerical simulation and hot-wire anemometry

2019 ◽  
Vol 213 ◽  
pp. 02076
Author(s):  
Jan Sip ◽  
Frantisek Lizal ◽  
Jakub Elcner ◽  
Jan Pokorny ◽  
Miroslav Jicha
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Velocity Field ◽  
Flow Field ◽  
Large Eddy Simulation ◽  
Turbulence Models ◽  
Hot Wire ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Precise Prediction

The velocity field in the area behind the automotive vent was measured by hot-wire anenemometry in detail and intensity of turbulence was calculated. Numerical simulation of the same flow field was performed using Computational fluid dynamics in commecial software STAR-CCM+. Several turbulence models were tested and compared with Large Eddy Simulation. The influence of turbulence model on the results of air flow from the vent was investigated. The comparison of simulations and experimental results showed that most precise prediction of flow field was provided by Spalart-Allmaras model. Large eddy simulation did not provide results in quality that would compensate for the increased computing cost.

scholarly journals Investigation of flow separation in a centrifugal pump impeller based on improved delayed detached eddy simulation method

2019 ◽  
Vol 11 (12) ◽  
pp. 168781401989783
Author(s):  
Yun Ren ◽  
Zuchao Zhu ◽  
Denghao Wu ◽  
Xiaojun Li ◽  
Lanfang Jiang
Keyword(s):  
Large Eddy Simulation ◽  
Centrifugal Pump ◽  
Flow Separation ◽  
Hybrid Algorithm ◽  
Internal Flow ◽  
Navier Stokes ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Reynolds Averaged Navier Stokes ◽  
Vorticity Flux

The mechanism of flow separation in the impeller of a centrifugal pump with a low specific speed was explored by experimental, numerical, and theoretical methods. A novel delayed Reynolds-averaged Navier–Stokes/large eddy simulation hybrid algorithm combined with a rotation and curvature correction method was developed to calculate the inner flow field of the original pump for the large friction loss in the centrifugal impeller, high adverse pressure gradient, and large blade curvature. Boundary vorticity flux theory was introduced for internal flow diagnosis, and the relative velocity vector near the surface of the blade and the distribution of the dimensionless pressure coefficient was analyzed. The validity of the numerical method was verified, and the location of the backflow area and its flow features were determined. Finally, based on flow diagnosis, the geometric parameters influencing the flow state of the impeller were specifically adjusted to obtain a new design impeller. The results showed that the distribution of the boundary vorticity flux peak values, the skin friction streamline, and near-wall relative velocities improved significantly after the design change. In addition, the flow separation was delayed, the force applied on the blade was improved, the head under the part-load condition was improved, and the hydraulic efficiency was improved over the global flow ranges. It was demonstrated that the delayed Reynolds-averaged Navier–Stokes/large eddy simulation hybrid algorithm was capable to capture the separation flow in a centrifugal pump, and the boundary vorticity flux theory was suitable for the internal flow diagnosis of centrifugal pump.

scholarly journals Optimization of the Turbulence Model on Numerical Simulations of Flow Field within a Hydrocyclone

2015 ◽  
Vol 2015 ◽  
pp. 1-7
Author(s):  
Yan Xu ◽  
Zunce Wang ◽  
Lin Ke ◽  
Sen Li ◽  
Jinglong Zhang
Keyword(s):  
Flow Field ◽  
Large Eddy Simulation ◽  
Cross Sections ◽  
Three Dimensional ◽  
Reynolds Stress Model ◽  
Computational Grids ◽  
Test Results ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Simulation Results

Reynolds Stress Model and Large Eddy Simulation are used to respectively perform numerical simulation for the flow field of a hydrocyclone. The three-dimensional hexahedral computational grids were generated. Turbulence intensity, vorticity, and the velocity distribution of different cross sections were gained. The velocity simulation results were compared with the LDV test results, and the results indicated that Large Eddy Simulation was more close to LDV experimental data. Large Eddy Simulation was a relatively appropriate method for simulation of flow field within a hydrocyclone.

Large-eddy simulation of the Richtmyer–Meshkov instability

2015 ◽  
Vol 93 (10) ◽  
pp. 1124-1130 ◽  
Author(s):  
T. Wang ◽  
P. Li ◽  
J.S. Bai ◽  
G. Tao ◽  
B. Wang ◽  
...  
Keyword(s):  
Kinetic Energy ◽  
Flow Field ◽  
Large Eddy Simulation ◽  
Turbulent Kinetic Energy ◽  
Interface Instability ◽  
Simulation Code ◽  
Interface Evolution ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Turbulence Mixing

The subgrid-scale (SGS) terms of turbulence transport are modelled by the stretched-vortex SGS stress model, and a large-eddy simulation code multi-viscous fluid and turbulence (MVFT) is developed to investigate the MVFT problems. Then one AWE shock tube experiment of interface instability is simulated numerically by MVFT code, which reproduces the development process of the interface. The obtained numerical images of interface evolution and wave structures in flow field are consistent with the experimental results. The evolution of perturbed interface and propagation of shock waves in flow field and their interactions are analyzed in detail. The statistics features of turbulence mixing in the form of finer quantities, such as the turbulent kinetic energy, enstrophy, density variance, and turbulent mass flux are investigated, which also proves that the SGS model has a key role in large-eddy simulation. The turbulent kinetic energy and enstrophy decay with time as a power law.

Large Eddy Simulation and CDNS Investigation of T106C Low-Pressure Turbine

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
Site Hu ◽  
Chao Zhou ◽  
Zhenhua Xia ◽  
Shiyi Chen
Keyword(s):  
Large Eddy Simulation ◽  
Flow Separation ◽  
Separated Flow ◽  
Low Pressure ◽  
Secondary Flows ◽  
Computational Domain ◽  
Suction Surface ◽  
Low Pressure Turbine ◽  
Eddy Simulation ◽  
Large Eddy

This study investigates the aerodynamic performance of a low-pressure turbine, namely the T106C, by large eddy simulation (LES) and coarse grid direct numerical simulation (CDNS) at a Reynolds number of 100,000. Existing experimental data were used to validate the computational fluid dynamics (CFD) tool. The effects of subgrid scale (SGS) models, mesh densities, computational domains and boundary conditions on the CFD predictions are studied. On the blade suction surface, a separation zone starts at a location of about 55% along the suction surface. The prediction of flow separation on the turbine blade is always found to be difficult and is one of the focuses of this work. The ability of Smagorinsky and wall-adapting local eddy viscosity (WALE) model in predicting the flow separation is compared. WALE model produces better predictions than the Smagorinsky model. CDNS produces very similar predictions to WALE model. With a finer mesh, the difference due to SGS models becomes smaller. The size of the computational domain is also important. At blade midspan, three-dimensional (3D) features of the separated flow have an effect on the downstream flows, especially for the area near the reattachment. By further considering the effects of endwall secondary flows, a better prediction of the flow separation near the blade midspan can be achieved. The effect of the endwall secondary flow on the blade suction surface separation at the midspan is explained with the analytical method based on the Biot–Savart Law.

Numerical laser beam propagation using large eddy simulation of a jet engine flow field

2015 ◽  
Vol 54 (08) ◽  
pp. 1 ◽  
Author(s):  
Markus Henriksson ◽  
Lars J. Sjöqvist ◽  
Oskar Parmhed ◽  
Christer Fureby
Keyword(s):  
Flow Field ◽  
Large Eddy Simulation ◽  
Laser Beam ◽  
Beam Propagation ◽  
Laser Beam Propagation ◽  
Jet Engine ◽  
Eddy Simulation ◽  
Large Eddy
Sign in / Sign up

Export Citation Format

Share Document