Review of shear design methods for reinforced concrete beams strengthened with fibre reinforced polymer sheets

2001 ◽  
Vol 28 (2) ◽  
pp. 271-281 ◽  
Author(s):  
Christophe Deniaud ◽  
JJ Roger Cheng
Keyword(s):  
Reinforced Concrete ◽  
Glass Fibre ◽  
Mechanical Model ◽  
Concrete Beams ◽  
Design Methods ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Shear Design ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer

This paper reviews the different shear design methods found in the literature for reinforced concrete beams strengthened externally with fibre reinforced polymer (FRP) sheets and compares the adequacy of each method by using the test results from the University of Alberta. The FRP shear design methods presented include the effective FRP strain and the bond mechanism criteria, the strut-and-tie model, the modified compression field theory, and a mechanical model based on the strip method with shear friction approach. Sixteen full-scale T-beam test results were used in the evaluation. Two web heights of 250 and 450 mm and two ready mix concrete batches of 29 and 44 MPa were used in the test specimens. Closed stirrups were used with three spacings: 200 mm, 400 mm, and no stirrups. Three types of FRP were used to strengthen externally the web of the T-beams: (i) uniaxial glass fibre, (ii) triaxial (0/60/–60) glass fibre, and (iii) uniaxial carbon fibre. The results showed that the mechanical model using the strip method with shear friction approach evaluates better the FRP shear contribution. The predicted capacities from this mechanical model are also found conservative and in excellent agreement with the test results.Key words: beams, carbon fibres, composite materials, fibre reinforced polymers, glass fibres, rehabilitation, reinforced concrete, shear strength, sheets, tests.

Does the shear strength of reinforced concrete beams and slabs depend upon the flexural reinforcement ratio or the reinforcement strain?

2013 ◽  
Vol 40 (11) ◽  
pp. 1068-1081 ◽  
Author(s):  
Mitra Noghreh Khaja ◽  
Edward G. Sherwood
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Shear Stresses ◽  
Shear Design ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
General Method

Beam tests are conducted to investigate the effect of the reinforcement ratio, ρ, and the shear span to depth ratio, a/d, on the shear strength of reinforced concrete beams and slabs without stirrups. The a/d ratio is shown to have a very significant effect on shear strength at both low values of a/d (where failure is governed by strut-and-tie mechanisms) and large values of a/d (where failure is governed by breakdown in beam action). Increases in ρ associated with increases in a/d such that the strain, or M/ρVd ratio, is kept constant will result in constant failure shear stresses. Shear design methods that do not account for a/d (e.g., ACI Committee 440) cannot predict the observed experimental behaviour, whereas the general method of the CSA A23.3 code can. Using the ACI 440 equation for Vc may reduce the economic competitiveness of fibre-reinforced polymer reinforcement versus steel reinforcement.

Behaviour of reinforced GFRP bars concrete beams having strengthened splices using CFRP sheets

2021 ◽  
pp. 136943322110015
Author(s):  
Akram S. Mahmoud ◽  
Ziadoon M. Ali
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
New Method ◽  
Gfrp Bars ◽  
Reinforced Polymer ◽  
Strength Capacity ◽  
Cfrp Sheet ◽  
Carbon Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer

When glass fibre-reinforced polymer (GFRP) bar splices are used in reinforced concrete sections, they affect the structural performance in two different ways: through the stress concentration in the section, and through the configuration of the GFRP–concrete bond. This study experimentally investigated a new method for increasing the bond strength of a GFRP lap (two GFRP bars connected together) using a carbon fibre-reinforced polymer (CFRP) sheet coated in epoxy resin. A new splicing method was investigated to quantify the effect of the bar surface bond on the development length, with reinforced concrete beams cast with laps in the concrete reinforcing bars at a known bending span length. Specimens were tested in four-point flexure tests to assess the strength capacity and failure mode. The results were summarised and compared within a standard lap made according to the ACI 318 specifications. The new method for splicing was more efficient for GFRP splice laps than the standard lap method. It could also be used for head-to-head reinforcement bar splices with the appropriate CFRP lapping sheets.

scholarly journals Efficacy of Thermally Conditioned Sisal FRP Composite on the Shear Characteristics of Reinforced Concrete Beams

2013 ◽  
Vol 2013 ◽  
pp. 1-14 ◽  
Author(s):  
Tara Sen ◽  
H. N. Jagannatha Reddy
Keyword(s):  
Reinforced Concrete ◽  
Polymer Composite ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Shear Strengthening ◽  
Sisal Fibre ◽  
Reinforced Polymer ◽  
Wide Range ◽  
Fibre Reinforced Polymer ◽  
Fracture Study

The development of commercially viable composites based on natural resources for a wide range of applications is on the rise. Efforts include new methods of production and the utilization of natural reinforcements to make biodegradable composites with lignocellulosic fibers, for various engineering applications. In this work, thermal conditioning of woven sisal fibre was carried out, followed by the development of woven sisal fibre reinforced polymer composite system, and its tensile and flexural behaviour was characterized. It was observed that thermal conditioning improved the tensile strength and the flexural strength of the woven sisal fibre composites, which were observed to bear superior values than those in the untreated ones. Then, the efficacy of woven sisal fibre reinforced polymer composite for shear strengthening of reinforced concrete beams was evaluated using two types of techniques: full and strip wrapping techniques. Detailed analysis of the load deflection behaviour and fracture study of reinforced concrete beams strengthened with woven sisal under shearing load were carried out, and it was concluded that woven sisal FRP strengthened beams, underwent very ductile nature of failure, without any delamination or debonding of sisal FRP, and also increased the shear strength and the first crack load of the reinforced concrete beams.

Sign in / Sign up

Export Citation Format

Share Document