Efficient numerical modelling for the design of friction damped braced steel plane frames

1989 ◽  
Vol 16 (3) ◽  
pp. 211-218 ◽  
Author(s):  
A. Filiatrault ◽  
S. Cherry
Keyword(s):  
Numerical Modelling ◽  
Performance Index ◽  
Load Distribution ◽  
Structural Response ◽  
Computer Time ◽  
Numerical Approach ◽  
Braced Frames ◽  
Friction Damping ◽  
Braced Frame ◽  
Brake Lining

A novel friction damping system for the aseismic design of framed buildings has been proposed by Canadian researchers. The system has been shown experimentally to perform very well and is an exciting development in earthquake resistant design.The design of a building equipped with the friction damping system is achieved by determining the optimum slip load distribution to minimize structural response. The optimum slip load distribution is usually determined using the general nonlinear dynamic computer program DRAIN-2D, which requires extensive computer time and is not practical for most design offices.This paper describes a new, efficient, numerical modelling approach for the design of friction damped braced frames. The hysteretic properties of the friction devices are derived theoretically and included in a friction damped braced frame analysis program, which is adaptable to a microcomputer environment. The optimum slip load distribution is determined by minimizing a relative performance index derived from energy concepts. The new numerical approach is much more economical to use than DRAIN-2D and is of great value for the practical design of friction damped braced frames. Key words: braced frames, brake lining, performance index, damping, dynamics, earthquakes, energy, friction.

Parameters influencing the design of friction damped structures

1989 ◽  
Vol 16 (5) ◽  
pp. 753-766 ◽  
Author(s):  
A. Filiatrault ◽  
S. Cherry
Keyword(s):  
Ground Motion ◽  
Seismic Design ◽  
Load Distribution ◽  
Simple Procedure ◽  
Structural Response ◽  
Earthquake Ground Motion ◽  
Construction Site ◽  
Efficient Design ◽  
Load Spectrum ◽  
Brake Lining

This paper is concerned with a study of the parameters influencing the seismic design of structures fitted with friction dampers. For the efficient design of such systems, the slip load distribution which minimizes structural response during a major earthquake must be determined for the dampers; this distribution is referred to herein as the optimum slip load distribution. A simple procedure is presented for establishing this basic design parameter. An analogy is first made between a single-storey friction damped structure and a simple nonlinear mechanical system. The response of this system to sinusoidal base excitation is then computed using an existing analytical solution. The solution clearly shows that the optimum slip load of the analogous friction damped structure depends on the amplitude and frequency of the ground motion and is not strictly a structural property. By extension, the optimum slip load distribution of a multistorey friction damped structure will be influenced by the characteristics of the earthquake ground motion anticipated at the construction site. Using this information, numerical sensitivity and parametric studies are performed on multistorey friction damped structures excited by a large number of artificial accelerograms generated from an existing stochastic earthquake model. The results of the study lead to the construction of a design slip load spectrum for the rapid evaluation of the optimum slip load distribution in a multistorey friction damped structure. The spectrum takes into account the properties of the structure and of the ground motion anticipated at the construction site and greatly simplifies the seismic design of this new structural system. Key words: braced frames, brake lining, design, damping, dynamics, earthquakes, energy, friction, slip load spectrum.

Development of a Hybrid Simulation Computational Model for Steel Braced Frames

2018 ◽  
Vol 763 ◽  
pp. 609-618
Author(s):  
Ali Imanpour ◽  
Robert Tremblay ◽  
Martin Leclerc ◽  
Romain Siguier
Keyword(s):  
Computational Model ◽  
Hybrid Simulation ◽  
Structural Testing ◽  
Frame Structure ◽  
Axial Stiffness ◽  
Braced Frames ◽  
Element Analysis ◽  
Braced Frame ◽  
Concentrically Braced Frame ◽  
Dynamic Hybrid

Hybrid simulation is an economical structural testing technique in which the critical part of the structure expected to respond in the inelastic range is tested physically whereas the rest of the structure is modelled numerically using a finite element analysis program. The article describes the development of a computational model for the hybrid simulation of the seismic collapse of a steel two-tiered braced frame structure due to column buckling. The column stability response in multi-tiered braced frames is first presented using a pure numerical model of the braced frame studied. The development of the hybrid simulation computational model is then discussed. Effects of initial out-of-straightness imperfections and axial stiffness, P-Delta analysis approach, and gravity analysis technique on the hybrid simulation results are evaluated using a numerical hybrid simulation model. Finally, the results of a continuous pseudo-dynamic hybrid simulation of the seismic response of the steel multi-tiered concentrically braced frame are presented. The test showed that failure of columns by instability is a possibility and can lead to collapse of multi-tiered braced frames, as was predicted by numerical analysis. Furthermore, suitable modeling methods are proposed for hybrid simulation of steel braced frame structures.

scholarly journals MODELLING THE WOLF ROCK LIGHTHOUSE

2020 ◽  
pp. 32
Author(s):  
Darshana Tharindra Dassanayake ◽  
Alison Raby ◽  
Edward Ransley ◽  
Alessandro Antonini ◽  
Kieran Monk ◽  
...  
Keyword(s):  
Numerical Modelling ◽  
Deep Water ◽  
Structural Response ◽  
Winter Storms

Wolf Rock lighthouse (1870) is an isolated offshore rock tower off the Southwest tip of England, built on a steep pinnacle. It is surrounded by relatively deep water, i.e. 60-70m. The lighthouse is battered by Atlantic winter storms, which result in dramatic wave impacts and exceptional runup, even reaching to its 41m high lantern level. New experimental and numerical modelling campaigns are carried out to understand the structural response of this engineering marvel. This paper will present the main results of the hydrodynamic investigations, highlighting the main issues and achievements of the first-ever attempted model of a rock lighthouse with the ambitious scale of 1:40.Recorded Presentation from the vICCE (YouTube Link): https://youtu.be/n5L5TcBiWvo

scholarly journals THE USE OF ARRAY PROCESSORS FOR NUMERICAL MODELLING OF TIDAL ESTUARY DYNAMICS

1980 ◽  
Vol 1 (17) ◽  
pp. 142
Author(s):  
D. Prandle ◽  
E.R. Funke ◽  
N.L. Crookshank ◽  
R. Renner
Keyword(s):  
Numerical Model ◽  
Numerical Modelling ◽  
Hybrid Model ◽  
Numerical Models ◽  
Computer Time ◽  
Scale Model ◽  
Hybrid Modelling ◽  
Tidal Propagation ◽  
Physical Scale ◽  
Array Processors

The use of array processors for the numerical modelling of estuarine systems is discussed here in the context of "hybrid modelling", however, it is shown that array processors may be used to advantage in independent numerical simulations. Hybrid modelling of tidal estuaries was first introduced by fiolz (1977) and later by Funke and Crookshank (1978). In a hybrid model, tidal propagation in an estuary is simulated by dynamically linking an hydraulic (or physical) scale model of part of the estuary to a numerical model of the remaining part in a manner such that a free interchange of flow occurs at the interface(s). Typically, the elevation of the water surface at the boundary of the scale model is measured and transmitted to the numerical model. In return, the flow computed at the boundary of the numerical model is fed directly into the scale model. This approach enables the extent of the scale model to be limited to the area of immediate interest (or to that area where flow conditions are such that they can be most accurately simulated by a scale model). In addition, since the region simulated by the numerical model can be extended almost indefinitely, the problems of spurious reflections from downstream boundaries can be eliminated. In normal use, numerical models are evaluated on the basis of computing requirements, cost and accuracy. The computer time required to simulate one tide cycle is, in itself, seldom of interest except in so far as it affects the above criteria. However in hybrid modelling this parameter is often paramount since concurrent operation of the numerical and scale models requires that the former must keep pace with the latter. The earlier hybrid model of the St. Lawrence (Funke and Crookshank, 1978) involved a one-dimensional numerical model of the upstream regions of the river. However, future applications are likely to involve extensive two-dimensional numerical simulation.

A Numerical Approach for Simulation of Rock Fracturing in Engineering Blasting

2012 ◽  
pp. 203-224
Author(s):  
Mani Ram Saharan ◽  
Hani Mitri
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Numerical Modelling ◽  
Knowledge Base ◽  
Plane Stress ◽  
Numerical Approach ◽  
The Other ◽  
Brittle Rock ◽  
Rock Fracturing ◽  
Element Elimination

An approach for simulation of rock fracturing as a result of engineering blasting is presented in this paper. The approach uses element elimination technique within the framework of finite element method to capture the physics of engineering blasting. The approach does not require pre-placement of fracture paths which is the severe drawback of the other existing methodologies and approaches. Results of plane stress modelling for isotropic brittle rock behaviour are presented in this paper and these results are in good agreement with the existing knowledge base. The authors also review the existing approaches of numerical modelling to compare the efficacy of the element elimination technique. It is anticipated that the further developments with this approach can prove to be good experimental tool to improve engineering blasting operations.

Ground Motion Intensity Measures for Rocking Building Systems

2017 ◽  
Vol 33 (4) ◽  
pp. 1533-1554 ◽  
Author(s):  
Mehrdad Shokrabadi ◽  
Henry V. Burton
Keyword(s):  
Ground Motion ◽  
Structural Response ◽  
Ground Acceleration ◽  
Intensity Measures ◽  
Braced Frame ◽  
Residual Drift ◽  
Engineering Demand Parameter ◽  
Frame System ◽  
Ground Motion Records ◽  
Steel Braced Frame

This paper investigates the effectiveness of various ground motion intensity measures (IMs) in estimating the structural response of two types of rocking systems: (a) a controlled rocking steel braced frame system with self-centering action and (b) a rocking spine system for reinforced concrete infill frames. The IMs are evaluated based on the dispersion in engineering demand parameter (EDP) predictions (efficiency) and the sensitivity of the conditional distributions of EDPs to the distributions of the magnitudes, distances and spectral shape parameter (ε) of ground motion records (sufficiency). The EDPs include maximum transient and residual story drifts and peak floor accelerations. The spectral acceleration averaged over a range of periods (Sa avg) is most effective for predicting transient and residual drift demands and peak ground acceleration (PGA) is generally the best predictor of peak floor accelerations. The proximity of the frequency range most affecting an EDP to that best reflected in an IM is found to be a good indicator of the performance of that IM.

Earthquake resistant design of concentrically braced steel frames

1991 ◽  
Vol 18 (5) ◽  
pp. 839-850 ◽  
Author(s):  
R. G. Redwood ◽  
V. S. Channagiri
Keyword(s):  
Structural Engineering ◽  
Steel Structures ◽  
Braced Frames ◽  
Concentrically Braced Frames ◽  
Braced Frame ◽  
Earthquake Resistant Design ◽  
Earthquake Resistant ◽  
Concentrically Braced ◽  
Engineering Steel ◽  
The Impact

New provisions of the CSA standard for steel structures (CAN/CSA-S16.1-M89) dealing with detailing of concentrically braced frames for seismic design are described and related to requirements of the National Building Code of Canada. The basis of the new requirements is outlined, and an example eight-storey frame is used to outline a methodology for the design process for a ductile braced frame and to illustrate the impact of the provisions. Key words: design, structural engineering, steel, earthquakes, braced frame, standards.

Code provisions for seismic design for concentrically braced steel frames

1992 ◽  
Vol 19 (6) ◽  
pp. 1025-1031 ◽  
Author(s):  
R. G. Redwood ◽  
A. K. Jain
Keyword(s):  
Seismic Design ◽  
Structural Engineering ◽  
Steel Frames ◽  
Braced Frames ◽  
Concentrically Braced Frames ◽  
Braced Frame ◽  
Concentrically Braced ◽  
Interstorey Drift ◽  
Available Information ◽  
Steel Braced Frame

Extensive research into the inelastic seismic response of concentrically braced frames and their components has been carried out in the last two decades. This knowledge has now been incorporated into seismic design practice in several countries, notably the U.S.A., Canada, and New Zealand. In this paper, design specifications from these three countries, which derive largely from the same body of research, are compared. The basic design philosophy for concentrically braced steel frames, loading, and member detailing are examined. It is concluded that, in general, the Canadian specifications are in conformity with the available information and have many similar features to codes of the other countries. Significant differences exist in the classification of braced frames, between interstorey drift requirements, in the treatment of dual structural systems, and to a lesser extent in member detailing requirements. Some features of Canadian codes meriting review are identified. Key words: structural engineering, earthquakes, standards, steel, braced frame, ductility, concentric bracing, dual system.

Sign in / Sign up

Export Citation Format

Share Document