EVOLUTION OF CHAIN STRUCTURE OF ELECTRORHEOLOGICAL FLUIDS IN FLOW MODEL

2002 ◽  
Vol 16 (17n18) ◽  
pp. 2697-2703 ◽  
Author(s):  
X. P. ZHAO ◽  
X. Y. GAO ◽  
D. J. GAO
Keyword(s):  
Pressure Gradient ◽  
Flow Rate ◽  
Volume Flow Rate ◽  
Chain Structure ◽  
Volume Flow ◽  
Electrorheological Fluids ◽  
Relative Pressure ◽  
Dynamic Simulations ◽  
Er Fluids ◽  
The Relationship

The movement of particles in electrorheological (ER) fluids is analyzed by means of molecular dynamic simulations. We found that the velocity profile of particles can be divided into two zones. One zone near electrodes where particles' velocity profiles change periodically like "breathing type" is called transition zone. The other in the middle of two electrodes where particles move smoothly like a plug is called "plug zone". In addition, the relationship between volume flow rate and relative pressure gradient is simulated out. Factors such as volume flow rate, critical electric field, critical pressure gradient and response time of shutting up were also analyzed respectively.

Effects of heat transfer and the endoscope on Jeffrey fluid peristaltic flow in tubes

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
A.M. Abd-Alla ◽  
S.M. Abo-Dahab ◽  
M.A. Abdelhafez ◽  
Esraa N. Thabet
Keyword(s):  
Heat Transfer ◽  
Pressure Gradient ◽  
Flow Rate ◽  
Analytical Solutions ◽  
Volume Flow Rate ◽  
Peristaltic Flow ◽  
Volume Flow ◽  
Jeffrey Fluid ◽  
Temperature Profiles ◽  
Content Type

PurposeThis article aims to describe the effect of an endoscope and heat transfer on the peristaltic flow of a Jeffrey fluid through the gap between concentric uniform tubes.Design/methodology/approachThe mathematical model of the present problem is carried out under long wavelength and low Reynolds number approximations. Analytical solutions for the velocity, temperature profiles, pressure gradient and volume flow rate are obtained.FindingsThe results indicate that the effect of the wave amplitude, radius ratio, Grashof number, the ratio of relaxation to retardation times and the radius are very pronounced in the phenomena. Also, a comparison of obtaining an analytical solution against previous literatures shows satisfactory agreement.Originality/valueAnalytical solutions for the velocity, temperature profiles, pressure gradient and volume flow rate are obtained. Numerical integration is performed to analyze the pressure rise and frictional forces on the inner and outer tubes.

In Vitro Performance Assessment of Distal Protection Devices for Carotid Artery Stenting: Effect of Physiological Anatomy on Vascular Resistance

2007 ◽  
Vol 14 (5) ◽  
pp. 712-724 ◽  
Author(s):  
Gail M. Siewiorek ◽  
Mark H. Wholey ◽  
Ender A. Finol
Keyword(s):  
Carotid Artery ◽  
Pressure Gradient ◽  
Vascular Resistance ◽  
Flow Rate ◽  
Volume Flow Rate ◽  
Volume Flow ◽  
Physiological Anatomy ◽  
Protection Devices ◽  
Distal Protection

Purpose: To assess in vitro the performance of 5 distal protection devices (DPDs) by evaluating the capture efficiency, pressure gradient, volume flow rate, and vascular resistance in the internal carotid artery (ICA). Methods: The time-averaged mean peak velocity in the common carotid artery and a blood-mimicking solution were used to simulate physiological conditions in a silicone carotid phantom representing average human carotid artery geometry with a 70% symmetrical ICA stenosis. Five milligrams of dyed 200-μm nominal diameter polymer microspheres (larger than the pore size of the devices, except Spider RX, which was tested with 300-μm-diameter particles) were injected into the ICA. The percentages of particles missed after injection and lost during device retrieval were measured for the 5 devices (Spider RX, FilterWire EZ, RX Accunet, Angioguard XP, and Emboshield). The normalized pressure gradient, fraction of the volume flow rate, and vascular resistance in the ICA were calculated. Results: Spider RX captured the most particles (missing 0.06%, p<0.05) and yielded the smallest normalized pressure gradient increase (4.2%), the largest volume flow rate fraction (0.40), and the smallest vascular resistance in the ICA (272 mmHg/L·min−1, a 5.4% increase with respect to initial conditions). Angioguard XP captured the fewest particles (missing 36.3%, p<0.05 except Emboshield) and resulted in the largest normalized pressure gradient increase (37%) in the ICA. RX Accunet produced the smallest volume flow rate fraction in the ICA (0.30) and the largest vascular resistance in the ICA (470 mmHg/L·min−1, an 82.2% increase). Emboshield migrated ∼6 cm distal to the original position after particle injection. FilterWire EZ lost the fewest particles during retrieval (0.45%, p<0.05 except Accunet RX and Spider RX) and had the best overall performance with 200-μm emboli (p<0.05 except Accunet RX). Conclusion: None of the devices tested completely prevented embolization. Overall, Spider RX had the best performance and is conjectured to have the best wall apposition of the devices tested. Vascular resistance should be considered a key filter design parameter for performance testing since it represents a quantitative estimation of the “slow-flow phenomenon.” Our findings should be extrapolated cautiously to help interventionists choose the best device.

scholarly journals The effects of ambient conditions on the calibration of air flow plate standards

2013 ◽  
Vol 17 (5) ◽  
pp. 1517-1520
Author(s):  
Qian Miao ◽  
Rong-Chao Yang ◽  
Qing Zhang ◽  
Jing Cheng ◽  
Jia-Cun Shao ◽  
...  
Keyword(s):  
Relative Humidity ◽  
Flow Rate ◽  
Atmospheric Pressure ◽  
Volume Flow Rate ◽  
Air Flow ◽  
Volume Flow ◽  
Calibration Data ◽  
Ambient Conditions ◽  
Numerical Examples ◽  
The Relationship

The volume flow rate measured by air flow plate is influenced by the ambient conditions during the calibration. A series of numerical examples are conducted for the relationship and the outcomes demonstrated that the calibration is quite sensitive to the atmospheric pressure and the ambient temperature, but insensitive to relative humidity. The experiment model has been applied to calibration results with wide ranging ambient conditions. In conclusion, the results of this study demonstrate the benefits to calibration data of minimizing the effects of ambient conditions.

Novel epoxy/anhydride alternatives for biological electron microscopy: Physical and performance characteristis of embed 812 and LX 112 in combination with NSA/NMA/DMAE

1989 ◽  
Vol 47 ◽  
pp. 1000-1001
Author(s):  
Joe A. Mascorro ◽  
Gerald S. Kirby
Keyword(s):  
Electron Microscopy ◽  
Flow Rate ◽  
Succinic Anhydride ◽  
Volume Flow Rate ◽  
Mass Density ◽  
Uranyl Acetate ◽  
Volume Flow ◽  
Base Resin ◽  
And Performance ◽  
Acid Anhydrides

Embedding media based upon an epoxy resin of choice and the acid anhydrides dodecenyl succinic anhydride (DDSA), nadic methyl anhydride (NMA), and catalyzed by the tertiary amine 2,4,6-Tri(dimethylaminomethyl) phenol (DMP-30) are widely used in biological electron microscopy. These media possess a viscosity character that can impair tissue infiltration, particularly if original Epon 812 is utilized as the base resin. Other resins that are considerably less viscous than Epon 812 now are available as replacements. Likewise, nonenyl succinic anhydride (NSA) and dimethylaminoethanol (DMAE) are more fluid than their counterparts DDSA and DMP- 30 commonly used in earlier formulations. This work utilizes novel epoxy and anhydride combinations in order to produce embedding media with desirable flow rate and viscosity parameters that, in turn, would allow the medium to optimally infiltrate tissues. Specifically, embeding media based on EmBed 812 or LX 112 with NSA (in place of DDSA) and DMAE (replacing DMP-30), with NMA remaining constant, are formulated and offered as alternatives for routine biological work.Individual epoxy resins (Table I) or complete embedding media (Tables II-III) were tested for flow rate and viscosity. The novel media were further examined for their ability to infilftrate tissues, polymerize, sectioning and staining character, as well as strength and stability to the electron beam and column vacuum. For physical comparisons, a volume (9 ml) of either resin or media was aspirated into a capillary viscocimeter oriented vertically. The material was then allowed to flow out freely under the influence of gravity and the flow time necessary for the volume to exit was recored (Col B,C; Tables). In addition, the volume flow rate (ml flowing/second; Col D, Tables) was measured. Viscosity (n) could then be determined by using the Hagen-Poiseville relation for laminar flow, n = c.p/Q, where c = a geometric constant from an instrument calibration with water, p = mass density, and Q = volume flow rate. Mass weight and density of the materials were determined as well (Col F,G; Tables). Infiltration schedules utilized were short (1/2 hr 1:1, 3 hrs full resin), intermediate (1/2 hr 1:1, 6 hrs full resin) , or long (1/2 hr 1:1, 6 hrs full resin) in total time. Polymerization schedules ranging from 15 hrs (overnight) through 24, 36, or 48 hrs were tested. Sections demonstrating gold interference colors were collected on unsupported 200- 300 mesh grids and stained sequentially with uranyl acetate and lead citrate.

Slip And Hall Effects On The Flow Of A Hyperbolic Tangent Fluid Through Porous Medium In A Planar Channel With Peristalsis

GIS Business ◽  
2020 ◽  
Vol 15 (1) ◽  
pp. 383-394
Author(s):  
K. Shalini ◽  
K.Rajasekhar
Keyword(s):  
Porous Medium ◽  
Pressure Gradient ◽  
Volume Flow Rate ◽  
Perturbation Technique ◽  
Volume Flow ◽  
Planar Channel ◽  
Hyperbolic Tangent ◽  
Closed Form Solutions ◽  
Long Wavelength ◽  
Hall Effects

In this paper, the effect of Slip and Hall effects on the flow of Hyperbolic tangent fluid through a porous medium in a planar channel with peristalsis under the assumption of long wavelength is investigated. A Closed form solutions are obtained for axial velocity and pressure gradient by employing perturbation technique. The effects of various emerging parameters on the pressure gradient, time averaged volume flow rate and frictional force are discussed with the aid of graphs.

Multi-objective optimization of squirrel cage fan for range hood based on Kriging model

2021 ◽  
pp. 095440622199586
Author(s):  
Qianhao Xiao ◽  
Jun Wang ◽  
Boyan Jiang ◽  
Weigang Yang ◽  
Xiaopei Yang
Keyword(s):  
Flow Rate ◽  
Optimization Design ◽  
Volume Flow Rate ◽  
Kriging Model ◽  
Volume Flow ◽  
Design Parameters ◽  
Multi Objective Optimization ◽  
Nsga Ii ◽  
Multi Objective ◽  
Squirrel Cage

In view of the multi-objective optimization design of the squirrel cage fan for the range hood, a blade parameterization method based on the quadratic non-uniform B-spline (NUBS) determined by four control points was proposed to control the outlet angle, chord length and maximum camber of the blade. Morris-Mitchell criteria were used to obtain the optimal Latin hypercube sample based on the evolutionary operation, and different subsets of sample numbers were created to study the influence of sample numbers on the multi-objective optimization results. The Kriging model, which can accurately reflect the response relationship between design variables and optimization objectives, was established. The second-generation Non-dominated Sorting Genetic algorithm (NSGA-II) was used to optimize the volume flow rate at the best efficiency point (BEP) and the maximum volume flow rate point (MVP). The results show that the design parameters corresponding to the optimization results under different sample numbers are not the same, and the fluctuation range of the optimal design parameters is related to the influence of the design parameters on the optimization objectives. Compared with the prototype, the optimized impeller increases the radial velocity of the impeller outlet, reduces the flow loss in the volute, and increases the diffusion capacity, which improves the volume flow rate, and efficiency of the range hood system under multiple working conditions.

scholarly journals Influence of Magnetic Field on the Peristaltic Flow of a Viscous Fluid through a Finite-Length Cylindrical Tube

2010 ◽  
Vol 7 (3) ◽  
pp. 169-176 ◽  
Author(s):  
S. K. Pandey ◽  
Dharmendra Tripathi
Keyword(s):  
Magnetic Field ◽  
Viscous Fluid ◽  
Transverse Magnetic Field ◽  
Finite Length ◽  
Flow Rate ◽  
Hartmann Number ◽  
Volume Flow Rate ◽  
Critical Value ◽  
Transverse Magnetic ◽  
Volume Flow

The paper presents an analytical investigation of the peristaltic transport of a viscous fluid under the influence of a magnetic field through a tube of finite length in a dimensionless form. The expressions of pressure gradient, volume flow rate, average volume flow rate and local wall shear stress have been obtained. The effects of the transverse magnetic field and electrical conductivity (i.e. the Hartmann number) on the mechanical efficiency of a peristaltic pump have also been studied. The reflux phenomenon is also investigated. It is concluded, on the basis of the pressure distribution along the tubular length and pumping efficiency, that if the transverse magnetic field and the electric conductivity increase, the pumping machinery exerts more pressure for pushing the fluid forward. There is a linear relation between the averaged flow rate and the pressure applied across one wavelength that can restrain the flow due to peristalsis. It is found that there is a particular value of the averaged flow rate corresponding to a particular pressure that does not depend on the Hartmann number. Naming these values ‘critical values’, it is concluded that the pressure required for checking the flow increases with the Hartmann number above the critical value and decreases with it below the critical value. It is also inferred that magneto-hydrodynamic parameters make the fluid more prone to flow reversal. The conclusion applied to oesophageal swallowing reveals that normal water is easier to swallow than saline water. The latter is more prone to flow reversal. A significant difference between the propagation of the integral and non-integral number of waves along the tube is that pressure peaks are identical in the former and different in the latter cases.

Sign in / Sign up

Export Citation Format

Share Document