The structures, phase transition and elastic and thermodynamic properties of ZnS from first-principles calculations

2021 ◽  
pp. 2150143
Author(s):  
Bo Li ◽  
Weiyi Ren
Keyword(s):  
Phase Transition ◽  
Thermodynamic Properties ◽  
Bulk Modulus ◽  
First Principles ◽  
Density Functional ◽  
Mechanical Stability ◽  
Theoretical Data ◽  
Debye Model ◽  
Volume Curve ◽  
Temperature And Pressure

The phase transition of zinc sulfide (ZnS) from Zinc-blende (ZB) to a rocksalt (RS) structure and the elastic, thermodynamic properties of the two structures under high temperature and pressure are investigated by first-principles study based on the pseudo-potential plane-wave density functional theory (DFT) combined with the quasi-harmonic Debye model. The lattice constant [Formula: see text], bulk modulus [Formula: see text] and the pressure derivative of bulk modulus [Formula: see text]’ of the two structures are calculated. The results are in good agreement with experimental results and the other theoretical data. From the energy–volume curve, enthalpy equal principle and mechanical stability criterion, the transition pressures from the ZB to the RS structure are 16.83, 16.96 and 16.61 GPa, respectively. The three results and the experimental values 14.7–18.1, 16 GPa are very close to each other. Then the elastic properties are also calculated under the pressure ranging from 0 to 30 GPa. Finally, through the quasi-harmonic Debye model, the thermodynamic properties dependence of temperature and pressure in the ranges between 0–1600 K and 0–30 GPa are obtained successfully.

The structure, elastic and thermodynamic properties of Ti2GaC from first-principles calculation

2019 ◽  
Vol 33 (06) ◽  
pp. 1950030 ◽  
Author(s):  
Xiao-Xia Pu ◽  
Xiao-Jiang Long ◽  
Lin Zhang ◽  
Jun Zhu
Keyword(s):  
Thermodynamic Properties ◽  
Elastic Constant ◽  
Bulk Modulus ◽  
Elastic Constants ◽  
First Principles ◽  
Density Functional ◽  
Mechanical Stability ◽  
Theoretical Data ◽  
Debye Model ◽  
First Principles Calculation

In this work, the structure, elastic and thermodynamic properties of Ti2GaC at high pressure (P) and high-temperature (T) are studied based on the density functional first-principles. The lattice parameters and elastic constants are well consistent with some theoretical data and experimental results. The elastic constant of Ti2GaC increase monotonously with the increase of pressure (P), which demonstrates the mechanical stability of Ti2GaC at the pressure (P) from 0 to 200 GPa. Mechanical properties including Poisson’s ratio ([Formula: see text]), Young’s modulus (E), shear modulus (G) and bulk modulus (B), which are obtained from elastic constants C[Formula: see text]. The ratio B/G value shows that Ti2GaC is a brittle material, but its enhancing ductility significantly with the elevate of pressure (P). The Grüneisen parameters ([Formula: see text]), thermal expansion coefficient ([Formula: see text]), heat capacity (C[Formula: see text]), elastic constant (C[Formula: see text]), bulk modulus (B), energy (E) and volume (V) with the change of temperature (T) or pressure (P) are calculated within the quasi-harmonic Debye model for pressure (P) and temperatures (T) range in 1600 K and 100 GPa. Besides, densities of states and energy band are also obtained and analyzed in comparison with available theoretical data.

First-Principles Calculations of Elastic and Thermodynamic Properties of Cubic CdTe

2011 ◽  
Vol 268-270 ◽  
pp. 886-891
Author(s):  
Ben Hai Yu ◽  
Dong Chen
Keyword(s):  
Experimental Data ◽  
Heat Capacity ◽  
Thermodynamic Properties ◽  
Bulk Modulus ◽  
First Principles ◽  
Debye Model ◽  
First Principles Calculations ◽  
Lattice Constants ◽  
Temperature And Pressure ◽  
The Relationship

the equilibrium lattice constants, elastic and thermodynamic properties of cubic CdTe are systemically investigated at high temperature using the plane-wave pseudopotential method as well as the quasi-harmonic Debye model. The bulk modulus of CdTe are calculated as a function of temperature up to 1000K, the relationship between bulk modulusBand pressure is also obtained. The results gained from this model will provide overall predictions accurately for the temperature and pressure dependence of various quantities such as the bulk modulus, the heat capacity and the thermal expansion coefficient. More over, the dependences between Debye temperature and temperature are also successfully obtained. Our results are compared with the experimental data and discussed in light of previous works.

First-principles study of the phonon, mechanical and thermodynamic properties of B2-phase AlY under high pressures

2017 ◽  
Vol 31 (32) ◽  
pp. 1750254
Author(s):  
Leini Wang ◽  
Zhang Jian ◽  
Wei Ning
Keyword(s):  
High Pressure ◽  
Thermodynamic Properties ◽  
Elastic Constants ◽  
First Principles ◽  
Density Functional ◽  
High Pressures ◽  
Mechanical Stability ◽  
Debye Model ◽  
Functional Theory ◽  
B2 Phase

We have investigated the phonon, mechanical and thermodynamic properties of B2-phase AlY under high pressure by performing density functional theory (DFT). The result of phonon band structure shows B2-phase AlY exhibits dynamical stability. Then, the elastic properties of AlY under high pressure have been discussed. The elastic constants of AlY increase monotonically with the increase of the pressure and all the elastic constants meet the mechanical stability standard under high pressure. By analyzing the Poisson’s ratio [Formula: see text] and the value of B/G of AlY, we first predicted that AlY undergoes transformation from brittleness to ductility at 30 GPa and high pressure can improve the ductility. To obtain the thermodynamic properties of B2-phase AlY, the quasi-harmonic Debye model has been employed. Debye temperature [Formula: see text], thermal expansion coefficient [Formula: see text], heat capacity C[Formula: see text] and Grüneisen parameter [Formula: see text] of B2-phase AlY are systematically explored at pressure of 0–75 GPa and temperature of 0–700 K.

scholarly journals First-principles study of mechanical, vibrational and thermodynamic properties of magnetic XC compounds (X = Rb, Sr)

2017 ◽  
Vol 35 (3) ◽  
pp. 463-469
Author(s):  
A. Lakdja ◽  
I. Benzaidi ◽  
A. Sayede ◽  
A. Chahed
Keyword(s):  
Thermodynamic Properties ◽  
First Principles ◽  
Lattice Dynamics ◽  
Density Functional ◽  
Mechanical Stability ◽  
Ferromagnetic State ◽  
Debye Model ◽  
Lattice Dynamic ◽  
Density Functional Perturbation Theory ◽  
Response Scheme

AbstractLattice dynamic and mechanical properties of hypothetical RbC and SrC compounds were investigated using the ab-initio pseudopotential method and a linear response scheme. The lattice dynamics was studied in the framework of the density functional perturbation theory (DFPT). The dynamical and mechanical stability of the hypothetical RbC and SrC compounds was proved in their equilibrium B1 structure. In addition, the same stability was confirmed in the B3 phase. The thermodynamic properties were also investigated. They exhibited the same trend in both phases, and followed the Debye model. These results were confirmed in the ferromagnetic state, which makes the investigated compounds promising candidates in the spintronic field.

scholarly journals Pressure effect of the mechanical, electronics and thermodynamic properties of Mg–B compounds A first-principles investigations

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
GuoWei Zhang ◽  
Chao Xu ◽  
MingJie Wang ◽  
Ying Dong ◽  
FengEr Sun ◽  
...  
Keyword(s):  
Thermodynamic Properties ◽  
First Principles ◽  
Boron Content ◽  
Structural Parameters ◽  
Debye Model ◽  
Total Density ◽  
First Principle ◽  
Volume Deformation ◽  
Temperature And Pressure ◽  
Total Density Of States

AbstractFirst principle calculations were performed to investigate the structural, mechanical, electronic properties, and thermodynamic properties of three binary Mg–B compounds under pressure, by using the first principle method. The results implied that the structural parameters and the mechanical properties of the Mg–B compounds without pressure are well matched with the obtainable theoretically simulated values and experimental data. The obtained pressure–volume and energy–volume revealed that the three Mg–B compounds were mechanically stable, and the volume variation decreases with an increase in the boron content. The shear and volume deformation resistance indicated that the elastic constant Cij and bulk modulus B increased when the pressure increased up to 40 GPa, and that MgB7 had the strongest capacity to resist shear and volume deformation at zero pressure, which indicated the highest hardness. Meanwhile, MgB4 exhibited a ductility transformation behaviour at 30 GPa, and MgB2 and MgB7 displayed a brittle nature under all the considered pressure conditions. The anisotropy of the three Mg–B compounds under pressure were arranged as follows: MgB4 > MgB2 > MgB7. Moreover, the total density of states varied slightly and decreased with an increase in the pressure. The Debye temperature ΘD of the Mg–B compounds gradually increased with an increase in the pressure and the boron content. The temperature and pressure dependence of the heat capacity and the thermal expansion coefficient α were both obtained on the basis of Debye model under increased pressure from 0 to 40 GPa and increased temperatures. This paper brings a convenient understanding of the magnesium–boron alloys.

scholarly journals Novel structural phases and the properties of LaX (X = P, As) under high pressure: first-principles study

RSC Advances ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 3058-3070
Author(s):  
Yu Zhou ◽  
Lan-Ting Shi ◽  
A-Kun Liang ◽  
Zhao-Yi Zeng ◽  
Xiang-Rong Chen ◽  
...  
Keyword(s):  
Phase Transition ◽  
High Pressure ◽  
Thermodynamic Properties ◽  
First Principles ◽  
Electronic Structures ◽  
Pressure Range ◽  
Mechanical Stability ◽  
First Principles Study

The structures, phase transition, mechanical stability, electronic structures, and thermodynamic properties of lanthanide phosphates (LaP and LaAs) are studied in the pressure range of 0 to 100 GPa by first principles.

Structural, elastic and thermodynamic properties of A15-type compounds V3X (X = Ir, Pt and Au) from first-principles calculations

2016 ◽  
Vol 30 (35) ◽  
pp. 1650414 ◽  
Author(s):  
Mingliang Wang ◽  
Zhe Chen ◽  
Dong Chen ◽  
Cunjuan Xia ◽  
Yi Wu
Keyword(s):  
Thermodynamic Properties ◽  
Debye Temperature ◽  
First Principles ◽  
Density Functional ◽  
Coefficient Of Thermal Expansion ◽  
Local Density ◽  
Debye Model ◽  
First Principles Calculations ◽  
Generalized Gradient ◽  
Experimental Values

The structural, elastic and thermodynamic properties of the A15 structure V3Ir, V3Pt and V3Au were studied using first-principles calculations based on the density functional theory (DFT) within generalized gradient approximation (GGA) and local density approximation (LDA) methods. The results have shown that both GGA and LDA methods can process the structural optimization in good agreement with the available experimental parameters in the compounds. Furthermore, the elastic properties and Debye temperatures estimated by LDA method are typically larger than the GGA methods. However, the GGA methods can make better prediction with the experimental values of Debye temperature in V3Ir, V3Pt and V3Au, signifying the precision of the calculating work. Based on the E–V data derived from the GGA method, the variations of the Debye temperature, coefficient of thermal expansion and heat capacity under pressure ranging from 0 GPa to 50 GPa and at temperature ranging from 0 K to 1500 K were obtained and analyzed for all compounds using the quasi-harmonic Debye model.

scholarly journals Pressure Effect on Elastic Constants and Related Properties of Ti3Al Intermetallic Compound: A First-Principles Study

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2015 ◽  
Author(s):  
Xianshi Zeng ◽  
Rufang Peng ◽  
Yanlin Yu ◽  
Zuofu Hu ◽  
Yufeng Wen ◽  
...  
Keyword(s):  
Intermetallic Compound ◽  
Debye Temperature ◽  
Elastic Constants ◽  
First Principles ◽  
Density Functional ◽  
Mechanical Stability ◽  
Theoretical Data ◽  
Young’S Moduli ◽  
Anisotropic Factor ◽  
Isotropic Pressure

Using first-principles calculations based on density functional theory, the elastic constants and some of the related physical quantities, such as the bulk, shear, and Young’s moduli, Poisson’s ratio, anisotropic factor, acoustic velocity, minimum thermal conductivity, and Debye temperature, are reported in this paper for the hexagonal intermetallic compound Ti 3 Al. The obtained results are well consistent with the available experimental and theoretical data. The effect of pressure on all studied parameters was investigated. By the mechanical stability criteria under isotropic pressure, it is predicted that the compound is mechanically unstable at pressures above 71.4 GPa. Its ductility, anisotropy, and Debye temperature are enhanced with pressure.

scholarly journals Strain Conditions for the Inverse Heusler Type Fully Compensated Spin-Gapless Semiconductor Ti2MnAl: A First-Principles Study

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2091 ◽  
Author(s):  
Tie Yang ◽  
Liyu Hao ◽  
Rabah Khenata ◽  
Xiaotian Wang
Keyword(s):  
Thermodynamic Properties ◽  
First Principles ◽  
Density Functional ◽  
Theoretical Study ◽  
Debye Model ◽  
Pressure Effects ◽  
First Principles Calculation ◽  
Strain Condition ◽  
Functional Theory ◽  
Future Work

In this work, we systematically studied the structural, electronic, magnetic, mechanical and thermodynamic properties of the fully compensated spin-gapless inverse Heusler Ti2MnAl compound under pressure strain condition by applying the first-principles calculation based on density functional theory and the quasi-harmonic Debye model. The obtained structural, electronic and magnetic behaviors without pressure are well consistent with previous studies. It is found that the spin-gapless characteristic is destroyed at 20 GPa and then restored with further increase in pressure. While, the fully compensated ferromagnetism shows a better resistance against the pressure up to 30 GPa and then becomes to non-magnetism at higher pressure. Tetragonal distortion has also been investigated and it is found the spin-gapless property is only destroyed when c/a is less than 1 at 95% volume. Three independent elastic constants and various moduli have been calculated and they all show increasing tendency with pressure increase. Additionally, the pressure effects on the thermodynamic properties under different temperature have been studied, including the normalized volume, thermal expansion coefficient, heat capacity at constant volume, Grüneisen constant and Debye temperature. Overall, this theoretical study presents a detailed analysis of the physical properties’ variation under strain condition from different aspects on Ti2MnAl and, thus, can provide a helpful reference for the future work and even inspire some new studies and lead to some insight on the application of this material.

Thermodynamic Properties of CaSiO3 Perovskite at High Pressure and High Temperature

2009 ◽  
Vol 64 (5-6) ◽  
pp. 399-404 ◽  
Author(s):  
Zi-Jiang Liu ◽  
Xiao-Ming Tan ◽  
Yuan Guo ◽  
Xiao-Ping Zheng ◽  
Wen-Zhao Wu
Keyword(s):  
Thermodynamic Properties ◽  
First Principles ◽  
Density Functional ◽  
High Pressures ◽  
Local Density ◽  
Harmonic Approximation ◽  
Debye Model ◽  
Functional Theory ◽  
Casio3 Perovskite ◽  
First Time

The thermodynamic properties of tetragonal CaSiO3 perovskite are predicted at high pressures and temperatures using the Debye model for the first time. This model combines the ab initio calculations within local density approximation using pseudopotentials and a plane wave basis in the framework of density functional theory, and it takes into account the phononic effects within the quasi-harmonic approximation. It is found that the calculated equation of state is in excellent agreement with the observed values at ambient condition. Based on the first-principles study and the Debye model, the thermal properties including the Debye temperature, the heat capacity, the thermal expansion and the entropy are obtained in the whole pressure range from 0 to 150 GPa and temperature range from 0 to 2000 K.

Sign in / Sign up

Export Citation Format

Share Document