INVESTIGATION ON HIGH-TEMPERATURE CORROSION BEHAVIOR OF INCONEL 600 UNDER SO2-BEARING GAS AT 650°C

2019 ◽  
Vol 27 (06) ◽  
pp. 1950155
Author(s):  
KWANG-HU JUNG ◽  
SEONG-JONG KIM
Keyword(s):  
Electron Microscope ◽  
Weight Gain ◽  
High Temperature ◽  
Scanning Electron Microscope ◽  
High Temperature Corrosion ◽  
X Ray Diffraction ◽  
Oxide Structure ◽  
X Ray ◽  
Inconel 600 ◽  
Scanning Electron

The corrosion characteristics of Inconel 600 were investigated at 650∘C in air and 76%[Formula: see text]%[Formula: see text]%[Formula: see text]%SO2 gas environment up to 500[Formula: see text]h. Specimens exposed to each condition were characterized by weight gain, scanning electron microscope, energy dispersive X-ray spectroscopy and X-ray diffraction. The oxide structure consisting of the thin Cr2O3 layer and Cr2O3 nodules was observed, which increased the weight gain of specimens. In the SO2-bearing gas, it showed a bigger weight gain due to the coarsening of Cr2O3 nodules. Therefore, it was suggested that the sulfur-accelerated coarsening of Cr2O3 nodules at the high temperature.

Self-Propagating High-Temperature Synthesis of Fe-W(B, C) Based Composite

2013 ◽  
Vol 748 ◽  
pp. 46-50 ◽  
Author(s):  
Saowanee Singsarothai ◽  
Sutham Niyomwas
Keyword(s):  
Electron Microscope ◽  
High Temperature ◽  
Scanning Electron Microscope ◽  
The Self ◽  
X Ray Diffraction ◽  
Temperature Synthesis ◽  
X Ray ◽  
High Temperature Synthesis ◽  
Flame Ignition ◽  
Scanning Electron

Fe-W based composite have successfully been prepared using natural resource. The ferberite (Fe (Mn, Sn)WO4) tailings mixed with aluminum, carbon and boron oxide powder were used as reactants. The reactants were pressed and followed by oxy-acetylene flame ignition. The products from the self-propagating high-temperature synthesis (SHS) reaction were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM) couple with dispersive X-ray (EDS).

The Influence of the Hydrothermal Conditions on the Morphologies of β-Ni(OH)2

2012 ◽  
Vol 562-564 ◽  
pp. 494-497
Author(s):  
Xiao Ming Fu
Keyword(s):  
Electron Microscope ◽  
High Temperature ◽  
Reaction Time ◽  
Scanning Electron Microscope ◽  
Reaction Temperature ◽  
X Ray Diffraction ◽  
Hydrothermal Conditions ◽  
X Ray ◽  
Low Reaction Temperature ◽  
Scanning Electron

Flower-like β-Ni(OH)2 and nanoflakes have been successfully synthesized with nickel nitrate as nickel source and stronger ammonia water as precipitant via the hydrothermal method. The phase and the morphologies of the samples have been characterized and analyzed by XRD (X-ray diffraction) and SEM (Scanning electron microscope), respectively. XRD shows that the phase of the samples is β-Ni(OH)2. SEM confirms that The low reaction temperature is propitious to the synthesis of flower-like β-Ni(OH)2, and with the increase of the reaction time the nanoflakes of flower-like β-Ni(OH)2 become much thinner. However, The high temperature is in favor of the synthesis of β-Ni(OH)2 nanosflakes, and with the further increase of the reaction temperature.

Influence of SiC on the Properties of PcBN Cutting Tools Fabricated by High Pressure and High Temperature Sintering

2016 ◽  
Vol 697 ◽  
pp. 526-529 ◽  
Author(s):  
Shi Xun Zhang ◽  
Jian Li ◽  
Yao Ma ◽  
Hai Long Wang ◽  
Rui Zhang
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
Electron Microscope ◽  
High Temperature ◽  
Scanning Electron Microscope ◽  
Cutting Tools ◽  
X Ray Diffraction ◽  
Micro Structure ◽  
X Ray ◽  
Scanning Electron

SiC-Al3BC3-cBN composites with different contents of cBN were fabricated by high pressure and high temperature sintering (HPHT) at 1450 °C for 3 min under a pressure of 5.0 GPa using SiC, Al, B4C and C as additives. The effect of SiC content on the density and mechanical properties of SiC-Al3BC3-cBN composites was investigated. X-ray diffraction (XRD) and Scanning electron microscope (SEM) were used to analyze phases and micro-structure of the sintered samples. The hardness of SiC-Al3BC3-cBN composites decreased with the increasing of SiC content, However, the fracture strength of SiC-Al3BC3-cBN composites increased with the increasing of SiC content.

The Research of AlN-Mo Nano Composite Ceram

2013 ◽  
Vol 853 ◽  
pp. 57-61
Author(s):  
Chun Yu Xin
Keyword(s):  
High Pressure ◽  
Electron Microscope ◽  
High Temperature ◽  
Scanning Electron Microscope ◽  
X Ray Diffraction ◽  
Powder Synthesis ◽  
Nano Composite ◽  
X Ray ◽  
Structure Morphology ◽  
Scanning Electron

In this paper six sides top technology of high temperature and high pressure, in AlN nanopowder mixed with Mo powder, synthesis of AlN - Mo. Nanocomposite ceramics Using X-ray diffraction (XRD), scanning electron microscope (SEM) and vickers hardness instrument of AlN - Mo in the nanocomposite ceramics phase structure, morphology, size and hardness of the characterization, compared with AlN nanoceramic, discusses the AlN - Mo of nanocomposite ceramics new features.

The Influence of the Hydrothermal Temperature on the Morphologies of β-Ni(OH)2 Nanospheres and Nanoflakes

2012 ◽  
Vol 159 ◽  
pp. 376-379 ◽  
Author(s):  
Xiao Ming Fu
Keyword(s):  
Electron Microscope ◽  
High Temperature ◽  
Scanning Electron Microscope ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
Hydrothermal Temperature ◽  
X Ray ◽  
Low Reaction Temperature ◽  
Scanning Electron

β-Ni(OH)2 nanospheres and nanoflakes have been successfully synthesized with nickel nitrate as nickel source and stronger ammonia water as precipitant via the hydrothermal method. The phase and the morphologies of the samples have been characterized and analyzed by XRD (X-ray diffraction) and SEM (Scanning electron microscope), respectively. XRD analysis shows that the phase of the samples is β-Ni(OH)2. SEM analysis confirms that the low reaction temperature is propitious to the synthesis of β-Ni(OH)2 nanospheres. However, The high temperature is in favor of the synthesis of β-Ni(OH)2 nanosflakes.

Influence of Brazing Time on Microstructure of High Temperature Brazing Diamond with Ni-Cr Alloy

2012 ◽  
Vol 452-453 ◽  
pp. 628-632 ◽  
Author(s):  
Bin Sun ◽  
Pu Meng ◽  
Jin Bin Lu ◽  
Bin Zhao ◽  
Jian Jun Liu
Keyword(s):  
Electron Microscope ◽  
High Temperature ◽  
Scanning Electron Microscope ◽  
Growth Direction ◽  
Protective Atmosphere ◽  
Primary Reason ◽  
X Ray Diffraction ◽  
Strong Bond ◽  
X Ray ◽  
Scanning Electron

Samples of high temperature brazing diamond with Ni-Cr alloy are prepared in protective atmosphere furnace for brazing time is 1 minute, 2 minutes, and 5 minutes. The microstructures were analyzed with Scanning electron microscope, energy dispersive spectroscopy and X-ray diffraction. The results show that there are two layers of carbides on the surface of diamond, lamellar carbide Cr3C2 and columnar carbide Cr7C3, the growth direction of Cr3C2 has a certain orientation relationship with the crystallographic plane of diamond, and Cr7C3 nucleates on the surface of Cr3C2. With the increase of brazing time, the morphology of carbide Cr3C2 turns from linear to lamellar and carbide Cr7C3 turns from granule to columnar. After brazing, chemical metallurgical combination is achieved between diamonds and brazing alloy and carbides are the primary reason for the strong bond strength.

PENGGUNAAN TiO2 PARTIKEL NANO HASIL SINTESIS BERBASIS AIR MENGGUNAKAN METODA SOL-GEL PADA BAHAN KAPAS SEBAGAI APLIKASI UNTUK TEKSTIL ANTI UV

Arena Tekstil ◽  
2013 ◽  
Vol 28 (1) ◽  
Author(s):  
Maya Komalasari ◽  
Bambang Sunendar
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sol Gel ◽  
Crosslinking Agent ◽  
X Ray Diffraction ◽  
Nano Tio2 ◽  
X Ray ◽  
Infra Red ◽  
Scanning Electron

Partikel nano TiO2 berbasis air dengan pH basa telah berhasil disintesis dengan menggunakan metode sol-gel dan diimobilisasi pada kain kapas dengan menggunakan kitosan sebagai zat pengikat silang. Sintesis dilakukan  dengan prekursor TiCl4 pada konsentrasi 0,3 M, 0,5 M dan 1 M, dan menggunakan templat kanji dengan proses kalsinasi pada suhu 500˚C selama 2 jam. Partikel nano TiO2 diaplikasikan ke kain kapas dengan metoda pad-dry-cure dan menggunakan kitosan sebagai crosslinking agent. Berdasarkan hasil Scanning Electron Microscope (SEM),diketahui bahwa morfologi partikel TiO2 berbentuk spherical dengan ukuran nano (kurang dari 100 nm). Karakterisasi X-Ray Diffraction (XRD) menunjukkan adanya tiga tipe struktur kristal utama, yaitu (100), (101) dan (102) dengan fasa kristal yang terbentuk adalah anatase dan rutile. Pada karakterisasi menggunakan SEM terhadap serbuk dari TiO2 yang telah diaplikasikan ke permukaan kain kapas, terlihat adanya imobilisasi partikel nano TiO2 melalui ikatan hidrogen silang dengan kitosan pada kain kapas. Hasil analisa tersebut kemudian dikonfirmasi dengan FTIR (Fourier Transform Infra Red) yang hasilnya memperlihatkan puncak serapan pada bilangan gelombang 3495 cm-1, 2546 cm-1, dan 511 cm-1,  yang masing-masing diasumsikan sebagai adanya vibrasi gugus fungsi O-H, N-H dan Ti-O-Ti. Hasil SEM menunjukkan pula bahwa kristal nano yang terbentuk diantaranya adalah fasa rutile , yang berdasarkan literatur terbukti dapatberfungsi sebagai anti UV.

Effect of the Neodymium Content on Mechanical Properties of the Electro-Brush Plated Nano-Al2O3/Ni Composite Coating

2012 ◽  
Vol 525-526 ◽  
pp. 277-280
Author(s):  
Guo Jin ◽  
Xiu Fang Cui ◽  
Er Bao Liu ◽  
Qing Fen Li
Keyword(s):  
Mechanical Properties ◽  
Rare Earth ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Composite Coating ◽  
Nanoindentation Test ◽  
X Ray Diffraction ◽  
X Ray ◽  
Small Cracks ◽  
Scanning Electron

The effect of the neodymium content on mechanical properties of the electro-brush plated nanoAl2O3/Ni composite coating was investigated in this paper. The microstructure and phase structure were studied with scanning electron microscope (SEM) and X-ray diffraction (XRD). The hardness and abrasion properties of several coatings with different neodymium content were studied by nanoindentation test and friction / wear experiment. Results show that the coatings are much finer and more compact when the neodymium was added, and the hardness and abrasion property of the coatings with neodymium were improved obviously. Besides, the small cracks conduced by the upgrowth stress in the coatings were ameliorated when the rare earth neodymium was added. The improvement mechanism was further discussed.

Effect of Briquetting Pressure on the Performance of In Situ Formed Sialon in Al2O3-C Refractory Bricks

2014 ◽  
Vol 881-883 ◽  
pp. 1049-1052 ◽  
Author(s):  
Nai Peng ◽  
Cheng Ji Deng ◽  
Hong Xi Zhu
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
X Ray Diffraction ◽  
X Ray ◽  
Z Value ◽  
Refractory Bricks ◽  
Scanning Electron

In this paper, the effects of briquetting pressure on the performance of in-situ formed Sialon in Al2O3-C refractory bricks are investigated. The phase compositions and microstructure of the Al2O3-C refractory were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM).The results show the briquetting pressure hardly has effect on the phase of the sintered specimens, two new phases of Sialon with a Z value of 2 and SiC formed. The micrographs of Sialon crystals have the shape of both column and tabular column, but with a cone tip in the specimens sintered at 200MPa and 300MPa and smooth tip in specimens sintered at 400MPa and 500MPa.

Effect of Nickel on Titanium Carbide Synthesized via Tungsten Inert Gas (TIG) Method

2012 ◽  
Vol 620 ◽  
pp. 384-388
Author(s):  
Sharifah Aishah Syed Salim ◽  
Julie Juliewatty Mohamed ◽  
Zainal Arifin Ahmad ◽  
Zainal Arifin Ahmad
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Powder Mixture ◽  
Raw Material ◽  
Inert Gas ◽  
X Ray Diffraction ◽  
X Ray ◽  
Arc Melting ◽  
Elemental Powder Mixture ◽  
Scanning Electron

Numerous methods have been used to produce high purity TiC. There is no previous study has been reported on the formation using single elemental powders of Titanium (Ti) and Carbon (C) with addition Nickel (Ni) by tungsten inert gas (TIG) weld method. In this work, TiC was synthesized via TIG method by arc melting elemental powder mixture of Ti and C at ~5 second (s) and 80 ampere (A). The effect Ni contents on TiC formation was investigated. The mixed raw material was ball milled for 24 hours followed by synthesis via TIG method. The arced samples were characterized by X-ray diffraction (XRD) and Scanning electron microscope (SEM). It was revealed, that small amount of Ni additive to the metal powder allows the production of dense and tough TiC.

Sign in / Sign up

Export Citation Format

Share Document