Stability Prediction in High-Speed Milling Process Considering the Milling Force Coefficients Dependent on the Spindle Speed

2014 ◽  
Vol 13 (04) ◽  
pp. 247-255 ◽  
Author(s):  
Kunlong Wen ◽  
Houjun Qi ◽  
Gang Jin
Keyword(s):  
High Speed ◽  
Milling Process ◽  
Spindle Speed ◽  
Chatter Vibration ◽  
Milling Force ◽  
High Speed Milling ◽  
Force Coefficients ◽  
Stability Lobe ◽  
Vibration Model ◽  
The Stability

In order to further research the chatter vibration in high-speed milling, in this paper, a new regenerative chatter vibration model, considering the effect of milling force coefficients dependent on the spindle speed (MFCDSS) on the stability of high-speed milling process is proposed, and then milling stability lobe diagram is obtained, based on full-discretization method (FDM). The variable tendency of the stability of milling system is analyzed by comparisons in case of different radial immersion ratios in low-speed and high-speed milling regions, respectively. It is found that great stability predicting differences occur, especially in high-speed region when the MFCDSS is considered. This model can further supplement the theory of stability of high-speed milling process, it has certain engineering guidance significance in the selection of high-speed milling parameters.

scholarly journals Effect of High Speed Milling Process Parameters on the Milling Force and Surface Topography of AM50A Magnesium Alloy

2018 ◽  
Vol 36 (1) ◽  
pp. 124-131
Author(s):  
Hongji Zhang ◽  
Yuanyuan Ge ◽  
Hong Tang ◽  
Yaoyao Shi ◽  
Zengsheng Li
Keyword(s):  
Magnesium Alloy ◽  
Surface Quality ◽  
High Speed ◽  
Milling Process ◽  
Spindle Speed ◽  
Feed Speed ◽  
Milling Force ◽  
High Speed Milling ◽  
Milling Parameters

Within the scope of high speed milling process parameters, analyzed and discussed the effects of spindle speed, feed rate, milling depth and milling width on milling forces in the process of high speed milling of AM50A magnesium alloy. At the same time, the influence of milling parameters on the surface roughness of AM50A magnesium alloy has been revealed by means of the measurement of surface roughness and surface micro topography. High speed milling experiments of AM50A magnesium alloy were carried out by factorial design. Form the analysis of experimental results, The milling parameters, which have significant influence on milling force in high speed milling of AM50A magnesium alloy, are milling depth, milling width and feed speed, and the nonlinear characteristics of milling force and milling parameters. The milling force decreases with the increase of spindle in the given mill parameters. For the effects of milling parameters on surface quality of the performance, in the milling depth and feeding speed under certain conditions with the spindle speed increases the surface quality of AM50A magnesium alloy becomes better with the feed speed increases the surface quality becomes poor. When the spindle speed is greater than 12000r/min, the milling depth is less than 0.2mm, and the feed speed is less than 400mm/min, the milling surface quality can be obtained easily.

Dynamics and Stability of Milling Process Considering the Gyroscopic Effects

2009 ◽  
Vol 76-78 ◽  
pp. 624-629 ◽  
Author(s):  
Shan Shan Sun ◽  
W.X. Tang ◽  
H.F. Huang ◽  
Xi Qing Xu
Keyword(s):  
High Speed ◽  
Milling Process ◽  
Depth Of Cut ◽  
Stability Lobe Diagram ◽  
High Speed Milling ◽  
Stability Lobe ◽  
Ultra High Speed ◽  
Resonance Response ◽  
Critical Depth Of Cut ◽  
Gyroscopic Effects

A dynamics model is established considering gyroscopic effects due to high speed rotating spindle-tool system in ultra-high speed milling (USM). The proposed method for predicting stability enables a new 3D stability lobe diagram to be developed in the presence of gyroscopic effects, to cover all the intermediate stages of spindle speed. The influences of the gyroscopic effects on dynamics and stability in USM are analyzed. It is shown that the gyroscopic effects lower the resonance response frequencies of the spindle-tool system and the stable critical depth of cut in ultra-high speed milling.

Avoiding Instability on the Milling of Parts with Thin Features

2006 ◽  
Vol 526 ◽  
pp. 37-42 ◽  
Author(s):  
Francisco Javier Campa ◽  
Luis Norberto López de Lacalle ◽  
S. Herranz ◽  
Aitzol Lamikiz ◽  
A. Rivero
Keyword(s):  
Dynamic Model ◽  
High Speed ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Test Device ◽  
High Speed Milling ◽  
Thin Walls ◽  
Chatter Vibrations ◽  
The Stability ◽  
Selection Of

In this paper, a 3D dynamic model for the prediction of the stability lobes of high speed milling is presented, considering the combined flexibility of both tool and workpiece. The main aim is to avoid chatter vibrations on the finish milling of aeronautical parts, which include thin walls and thin floors. In this way the use of complex fixtures is eliminated. Hence, an accurate selection of both axial depth of cut and spindle speed can be accomplished. The model has been validated by means of a test device that simulates the behaviour of a thin floor.

scholarly journals Stability Analysis of Milling Process with Variable Spindle Speed and Pitch Angle considering Helix Angle and Process Phase Difference

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Gang Jin ◽  
Haotian Jiang ◽  
Jianxin Han ◽  
Zhanjie Li ◽  
Hua Li ◽  
...  
Keyword(s):  
Phase Difference ◽  
Pitch Angle ◽  
High Speed ◽  
Helix Angle ◽  
Stability Domain ◽  
Milling Process ◽  
Spindle Speed ◽  
The Stability ◽  
The Time Domain ◽  
Milling Chatter

Suppression of milling chatter by disrupting regenerative effect is a well-known method to obtain higher cutting stability domain. In this paper, a dynamic model of the milling process with variable spindle speed and pitch angle considering helix angle and process phase difference is presented. Then, an updated semidiscretization method is applied to obtain the stability chart. After the effectiveness of the proposed method is confirmed by comparisons with the previously published works and the time-domain simulations, lots of analyses are conducted to deeply evaluate the influence of the helix angle, the process phase difference, and feed per tooth on milling stability. Results show that the change of helix angle can result in significant stability discrepancies for both high-speed and low-speed regions. Though the process phase difference has the randomness and immeasurability in the practical application, it has an important influence on the stability and will result in a periodic evolution of the stability with a period π. Also, its recommended values are given for the practical milling process.

Structure Dynamic Modification and Optimization for High-Speed Face Milling Cutter

2004 ◽  
Vol 471-472 ◽  
pp. 663-667 ◽  
Author(s):  
Wei Xiao Tang ◽  
Xing Ai ◽  
H.Y. Wu ◽  
Song Zhang ◽  
H. Jiang
Keyword(s):  
High Speed ◽  
Milling Process ◽  
Face Milling ◽  
Relative Speed ◽  
Structural Dynamic ◽  
High Speed Milling ◽  
Structural Dynamic Modification ◽  
The Face ◽  
Dynamic Modification ◽  
The Stability

Due to the complexity of high-speed milling process by high relative speed and interrupted cutting, the face milling cutters possess the multi-order modes and the vibrating displacements of the cutting edges under each modes affect adversely both the surface roughness and the life of machine/tool system worse than other structures. In order to improve the stability of milling process, this work focuses on the influence of the variables such as structure geometries and constraint conditions on the eigenfrequencies and modeshapes of cutter. As an example, the dynamic characteristics of several face cutters are analyzed and optimized by structural dynamic modification (SDM) techniques.

STABILITY LOBES ANALYSIS OF NICKEL SUPERALLOYS MILLING

2011 ◽  
Vol 21 (10) ◽  
pp. 2943-2954 ◽  
Author(s):  
KRZYSZTOF KĘCIK ◽  
RAFAŁ RUSINEK ◽  
JERZY WARMIŃSKI
Keyword(s):  
High Speed ◽  
Milling Process ◽  
Recurrence Quantification Analysis ◽  
Nickel Superalloys ◽  
Stability Lobe ◽  
Stability Lobes ◽  
Recurrence Quantification ◽  
Quantification Analysis ◽  
The Stability ◽  
Inconel 713C

In this paper, we study the stability of a high speed milling process of nickel superalloys Inconel 713C by methods used in nonlinear dynamics. Stability Lobe Diagram was a result of modal analysis and next verified by recurrence plots, recurrence quantification analysis and classical nonlinear methods. A stability lobes diagram shows the indistinct boundary between chatter-free stable machining and unstable processes. Nevertheless, some recurrence quantification analysis measures give interesting results.

Experimental Study on High-Speed Milling of Aluminum Alloy 2A70

2011 ◽  
Vol 314-316 ◽  
pp. 1788-1791 ◽  
Author(s):  
Feng Yun Yu ◽  
Ming Jun Feng ◽  
Ming Jun Dai ◽  
Hong Jiang Sun
Keyword(s):  
Aluminum Alloy ◽  
Cutting Force ◽  
High Speed ◽  
Periodic Variation ◽  
Spindle Speed ◽  
Milling Force ◽  
Experimental Conditions ◽  
High Speed Milling ◽  
High Speed Cutting ◽  
Test Study

High-speed cutting technology is widely used in aviation, mold, automotive industries and other fields for its high machining efficiency, smaller cutting force, less cutting heat and high machining precision. However, the production site in China, high-speed machine tools do not really play its role in some enterprises, without real sense of the high-speed machining. Aluminum alloy 2A70 as the research object, using single-factor test, study the effect law of high-speed milling parameters on milling force here. The results show that: the cutting force is varying for high-speed milling, showing a periodic variation, with the transient characteristic, the milling force is large amplitude fluctuations in X and Y direction, the amount of change is respectively 55.544N and 56.306N. Milling force influenced by the spindle speed, with the increase of spindle speed, X contribute to the greatest change in the direction of milling, Y direction second, Z direction is almost unchanged. Under the experimental conditions, the stability high-speed cutting area of 2A70 is the spindle speed in the area of 21000rpm~27000rpm. The results of high-speed milling of aluminum alloy have certain significance.

Research on Stability of High Speed Milling System

2013 ◽  
Vol 670 ◽  
pp. 137-142
Author(s):  
Y.Y. Guo ◽  
H. Lei ◽  
C. Zhao ◽  
C.T. Sun
Keyword(s):  
High Speed ◽  
Metal Removal ◽  
Milling Process ◽  
Depth Of Cut ◽  
Engineering Practice ◽  
Model Parameters ◽  
High Speed Milling ◽  
Stability Lobes ◽  
The Stability ◽  
Axial Depth

Machining instability is often the limiting factor on metal removal rate. So the stability of cutting system is an important research in high-speed machining area. It is widely used in engineering practice. In this paper, the stability of high-speed milling was studied by the numbers aiming at the dynamic milling process model of ball-end mill. The dynamic model of high-speed milling process was established. On the basis of Altintas’s theory, the formula about the limit axial depth of cut was derived. Besides, the model parameters of the system were obtained and the accuracy of the stability lobes diagram was verified through the experiments. From this research, it was learned that structure parameters of machine tool-cutting tool system, cutting force coefficients, spindle speed and axial depth of cut were factors affecting the stability in high-speed cutting. And the obtained stability lobes diagram provided a reliable basis in selecting cutting parameters during tool path planning.

Experimental Study on Thermal and Force Characteristics in the Dry Slotting of Cortical Bone

2016 ◽  
Vol 1136 ◽  
pp. 233-238
Author(s):  
Liang Wen ◽  
Zi Han Zhao ◽  
Jin Bang Song ◽  
De Dong Yu ◽  
Ming Chen ◽  
...  
Keyword(s):  
Cutting Force ◽  
Cortical Bone ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
Growth Direction ◽  
Milling Process ◽  
Spindle Speed ◽  
Milling Force ◽  
Milling Temperature

Cutting force and temperature are the two chief factors affecting bone rehabilitation during bone cutting in many orthopedic surgeries. To reveal new knowledge of thermal and force when milling cortical bone, slotting experiments were carried on high-speed milling platform. Cutting force and temperature were measured during the milling process. The effects of cutting inputs on cutting thermal and force were researched in detail. The results showed that: feed rate and spindle speed had a great impact on the milling temperature, while the milling force was mainly influenced by spindle speed. A feed rate of 1.0-1.4 mm/s is recommended to obtain preferable milling force and temperature, and a larger feed rate of 1.2-1.4 mm/s is advised to use with a lower spindle speed (8000-20000 r/min), while a smaller feed rate of 1.0-1.2 mm/s should be chosen when spindle speed was between 20000-40000 r/min. Feeding parallel to the growth direction of the cortical bone can significantly reduce the milling temperature, but there was no obvious change in milling force. The lowest cutting temperature obtained during the experiment was around 50 °C without coolant, which was acceptable for orthopedic surgeries.

Sign in / Sign up

Export Citation Format

Share Document