Are Households Willing to Finance the Cost of Individual Water Supply? Case Study in Central Tunisia

2021 ◽  
Author(s):  
Marine Favre
Keyword(s):  
Water Supply ◽  
Central Tunisia ◽  
The Cost

scholarly journals Borehole Rehabilitation: A Case Study in the Dunkwa Mining Town

2020 ◽  
Vol 20 (2) ◽  
pp. 11-17
Author(s):  
A. Ewusi ◽  
J. Seidu
Keyword(s):  
Water Supply ◽  
Central Region ◽  
Pumping Test ◽  
Implementation Cost ◽  
Mining Town ◽  
Long Time ◽  
Borehole Camera ◽  
The Cost ◽  
Very High

Rehabilitation works were carried out on boreholes in the Dunkwa Mining town in the Central Region of Ghana. These works were carried out because the boreholes had lost their original yields due to clogging, corrosion and encrustation and had been abandoned for a long time. The cost of drilling a new well and assessing the productivity of the well is $4,500 which is more expensive that carrying out rehabilitation works which is cheaper, about $800. Also, the initial yields of the boreholes were very high according to the feasibility report which is not a common characteristic of the rocks in the area. Camera inspection followed by rehabilitation, pre and post pumping tests were carried out to assess whether there has been an improvement in their yield after the exercise and that the yield obtained will be adequate for a water supply design. Results show that all the boreholes had an improvement in their yields (57.19 - 259.80 %) after the rehabilitation. It can therefore be concluded that rehabilitation is effective in restoring boreholes to their original yields. Organisations drilling boreholes to communities can take advantage of rehabilitation of the existing boreholes located in the communities which are high yielding, thereby reducing project implementation cost. Keywords: Borehole Rehabilitation, Borehole Yields, Borehole Camera Inspection, Pumping Test

The Development of Rural Water Supply in the Province of Fayoum, Egypt

1993 ◽  
Vol 27 (9) ◽  
pp. 37-46 ◽  
Author(s):  
Abdel Rahman Abu Hamed ◽  
A. M. H. Sannen
Keyword(s):  
Water Supply ◽  
Production Capacity ◽  
Cost Recovery ◽  
Rural Water Supply ◽  
Rural Water ◽  
To Come ◽  
State Of Affairs ◽  
The Cost ◽  
Year 2000

The paper provides a case study of rural water supply in Fayoum. First, the present state-of-affairs is described and analyzed with respect to production, consumption and coverage. A water balance is drawn up and the projected trends up to the year 2000 are indicated. Nearly full coverage has been achieved already but still more than 50% of the population is served by public standposts. Considerable demand for house connections is apparent. Based on the present trend it is expected that by the year 2000, 75% of the population could be served by private connections, provided sufficient production capacity becomes available. Secondly, the focus is on organization and finance with special attention to cost recovery. Estimates for present billing efficiency and the Unaccounted For Water (UFW) percentages are provided. With the perceived trend in the growth of house connections and decline of public taps there is ample potential to reduce UFW, provided an efficient billing and fee collection system is introduced and leakage is controlled. With the reduction of UFW by “technical” measures half of the cost recovery target can be achieved. The other half has to come from tariff increases. Experience is drawn from the Netherlands-supported Fayoum Drinking Water and Sanitation Project (FADWS) which started in 1990.

scholarly journals Double-objective optimization-based firefly algorithm of a stand-alone photovoltaic/water pumping system for water supply in rural and remote areas: a case study

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Ruben Zieba Falama ◽  
Hamadou Bakari ◽  
Virgil Dumbrava
Keyword(s):  
Water Supply ◽  
Firefly Algorithm ◽  
Pumping System ◽  
Reservoir Volume ◽  
Water Pumping ◽  
Dynamic Head ◽  
Rural And Remote Areas ◽  
Total Investment ◽  
The Cost

AbstractA techno-economic study of a stand-alone PV water pumping system for water supply is done in this paper. An optimal design of the system is realized thanks to a double-objective optimization based on a proposed operational strategy of the system and on firefly algorithm (FA). The two objective functions simulated simultaneously using FA are: the function defining the cost of water (COW) and the function which defines the loss of water supply probability (LWSP). The system is designed to supply water to around 328 households in Cameroon, each composed by an average of six (06) persons. For different LWSP, the double-objective simulation determines the optimal configurations of the system with their related cost. The optimal and reliable (LWSP of 0%) system configuration obtained is composed by a number of 7 PV modules, a reservoir volume of 98.4 m3 with 2 days autonomy, a total dynamic head of 40 m, and a pump power of around 1 kW. The related COW corresponding to this configuration is 0.1185 $/m3, and the total investment cost is 27,506 $. The sensitivity analysis of the system revealed that the PV size, the volume of reservoir storage, and the efficiency of the pump influence the system both technically and economically, whereas the total dynamic head only influences the system economically. The validation of the optimized system has been done by comparison with manufacturer datasheets. It is demonstrated in this paper that the techno-economic analysis of energy systems based on multi-objective optimization using firefly algorithm is a powerful tool for decision-making.

Developing Schedule With Linear Programming (Case Study: STTF II Project Komplek Sukamukti Banjaran)

2020 ◽  
Vol 4 (02) ◽  
pp. 34-45
Author(s):  
Naufal Dzikri Afifi ◽  
Ika Arum Puspita ◽  
Mohammad Deni Akbar
Keyword(s):  
Linear Programming ◽  
Objective Function ◽  
Project Scheduling ◽  
Time Limit ◽  
Minimum Time ◽  
Service Cost ◽  
Trade Off ◽  
Overtime Work ◽  
The Cost

Shift to The Front II Komplek Sukamukti Banjaran Project is one of the projects implemented by one of the companies engaged in telecommunications. In its implementation, each project including Shift to The Front II Komplek Sukamukti Banjaran has a time limit specified in the contract. Project scheduling is an important role in predicting both the cost and time in a project. Every project should be able to complete the project before or just in the time specified in the contract. Delay in a project can be anticipated by accelerating the duration of completion by using the crashing method with the application of linear programming. Linear programming will help iteration in the calculation of crashing because if linear programming not used, iteration will be repeated. The objective function in this scheduling is to minimize the cost. This study aims to find a trade-off between the costs and the minimum time expected to complete this project. The acceleration of the duration of this study was carried out using the addition of 4 hours of overtime work, 3 hours of overtime work, 2 hours of overtime work, and 1 hour of overtime work. The normal time for this project is 35 days with a service fee of Rp. 52,335,690. From the results of the crashing analysis, the alternative chosen is to add 1 hour of overtime to 34 days with a total service cost of Rp. 52,375,492. This acceleration will affect the entire project because there are 33 different locations worked on Shift to The Front II and if all these locations can be accelerated then the duration of completion of the entire project will be effective

Perancangan dan Pembuatan Alat Bantu Meja Putar untuk Mesin Cnc 4 Axis

2016 ◽  
Vol 10 (2) ◽  
pp. 162-171
Author(s):  
Hafid Hafid ◽  
Tatang Sutisna
Keyword(s):  
Processing Time ◽  
Rotary Table ◽  
Engineering Process ◽  
Cnc Machine ◽  
Economical Analysis ◽  
Machining Center ◽  
Design And Manufacturing ◽  
The Cost ◽  
Productivity And Competitiveness

The design and manufacturing of the rotary table with the specification Ø 170 mm (6 inches) for CNC machine 4 axis has been done. The objective of manufacturing a rotary table is to increase the efficiency of CNC machine Hardford 4 axis to be above 80% in line machining center CV. IM’s workshop. The engineering methods was taken, consist of: working preparation, manufacturing of working drawing, engineering process, the manufacturing and testing. The prototype has been tested and operated, the resulting of increasing productivity of which were as follows: the process of assembling was increased to be 3 time ( before 1 time) and processing time for a specific case reduced from 5 hours to 3 hours, number of operators for the case of assembling the rotary reduced to 1 person (before 4 persons), safety and security become to be better. The results show increased efficiency of CNC machine Hardford, from under 50% to be above 80%. Based on the economical analysis obtained by the cost of good sold (C.G.S) of the rotary table is IDR 34.060.000. The results presented in this paper is expected to be case study for developing a business of the metal and engineering SMEs domestic to the effort of improving efficiency, quality, productivity and competitiveness in global market.ABSTRAKPerancangan dan pembuatan alat bantu meja putar (rotary table) dengan spesifikasi teknis Ø 170 mm (6 inci) untuk mesin CNC 4 axis telah dilakukan. Tujuan pembuatan rotary table adalah untuk meningkatkan efisiensi mesin CNC Hardford 4 axis di atas 80% pada line machining center Bengkel CV. IM. Metode rancang bangun yang dilakukan, meliputi: persiapan kerja, pembuatan gambar kerja, proses engineering, pembuatan dan uji coba. Prototip tersebut telah diuji coba dan dioperasikan dengan hasil peningkatan produktivitas sebagai berikut: proses pengerjaan bongkar pasang meningkat menjadi 3 kali (sebelumnya 1 kali) dan waktu pengerjaan untuk kasus tertentu berkurang dari 5 jam menjadi 3 jam, jumlah operator untuk kasus bongkar pasang rotary berkurang menjadi 1 orang (sebelumnya 4 orang), keselamatan kerja dan keamanan menjadi lebih baik. Hasil peningkatan berupa efisiensi mesin CNC Hardford 4 axis dari sebelumnya di bawah 50% menjadi di atas 80%. Berdasarkan hasil perhitungan analisis ekonomi diperoleh harga pokok produksi (HPP) alat bantu meja putar adalah sebesar Rp. 34.060.000. Bahasan ini diharapkan menjadi contoh kasus bagi pengembangan usaha IKM logam dan mesin dalam negeri untuk meningkatkan efisiensi, mutu, produktivitas dan keunggulan daya saing di pasar global.Kata kunci: alat bantu meja putar, mesin CNC, harga pokok produksi

PERSIAN GARDENS IN COLD AND DRY CLIMATE: A CASE STUDY OF TABRIZ’S HISTORICAL GARDENS

2016 ◽  
Vol 10 (3) ◽  
pp. 193
Author(s):  
Ahad Nejad Ebrahimi ◽  
Farnaz Nazarzadeh ◽  
Elnaz Nazarzadeh
Keyword(s):  
Comparative Study ◽  
Water Supply ◽  
Field Study ◽  
Cold Climate ◽  
Natural Substrate ◽  
Garden Design ◽  
Climate Conditions ◽  
North West ◽  
Special Expertise

Throughout history, gardens and garden designing has been in the attention of Persian architects who had special expertise in the construction of gardens. The appearance of Islam and allegories of paradise taken from that in Koran and Saints’ sayings gave spirituality to garden construction. Climate conditions have also had an important role in this respect but little research has been done about it and most of the investigations have referred to spiritual aspects and forms of garden. The cold and dry climate that has enveloped parts of West and North West of Iran has many gardens with different forms and functions, which have not been paid much attention to by studies done so far. The aim of this paper is to identify the features and specifications of cold and dry climate gardens with an emphasis on Tabriz’s Gardens.  Due to its natural and strategic situation, Tabriz has always been in the attention of governments throughout history; travellers and tourists have mentioned Tabriz as a city that has beautiful gardens. But, the earthquakes and wars have left no remains of those beautiful gardens. This investigation, by a comparative study of the climates in Iran and the effect of those climates on the formation of gardens and garden design, tries to identify the features and characteristics of gardens in cold and dry climate. The method of study is interpretive-historical on the basis of written documents and historic features and field study of existing gardens in this climate. The results show that, with respect to natural substrate, vegetation, the form of water supply, and the general form of the garden; gardens in dry and cold climate are different from gardens in other climates.

Case Study—Failure Analysis of a Multiplexer

2016 ◽  
Author(s):  
Michael Woo ◽  
Marcos Campos ◽  
Luigi Aranda
Keyword(s):  
Failure Analysis ◽  
High Reliability ◽  
Component Failure ◽  
Root Cause ◽  
Knowing That ◽  
Cause Of Failure ◽  
The Cost

Abstract A component failure has the potential to significantly impact the cost, manufacturing schedule, and/or the perceived reliability of a system, especially if the root cause of the failure is not known. A failure analysis is often key to mitigating the effects of a componentlevel failure to a customer or a system; minimizing schedule slips, minimizing related accrued costs to the customer, and allowing for the completion of the system with confidence that the reliability of the product had not been compromised. This case study will show how a detailed and systemic failure analysis was able to determine the exact cause of failure of a multiplexer in a high-reliability system, which allowed the manufacturer to confidently proceed with production knowing that the failure was not a systemic issue, but rather that it was a random “one time” event.

Sign in / Sign up

Export Citation Format

Share Document