Similarity simulation study on displacement and stress changes response to coal mining in Longdong coal mine, China

2020 ◽  
pp. qjegh2020-111
Author(s):  
Kai Huang ◽  
Long Xu ◽  
Fusheng Zha ◽  
Zhitang Lu ◽  
Jiwen Wu ◽  
...  
Keyword(s):  
Coal Seam ◽  
Coal Mine ◽  
Water Inrush ◽  
Coal Pillar ◽  
Working Face ◽  
Field Investigations ◽  
Geological Conditions ◽  
Stress Changes ◽  
Continuous Mining ◽  
The Stability

The complicated geological conditions, including the Fault Sun, in East No. 2 mining sub-area of the Longdong coal mine will influence the stability of strata during mining, leading to serious geological hazards. To circumvent this issue, a similarity simulation experiment was designed and performed in this study, in which the failure characteristics and evolution of displacement and stress within the strata were investigated, and the optimum width of a waterproof coal pillar was determined. The results showed that, as the working face progressed, the coal seam roof gradually deformed, from initial caving of the immediate roof to complete movement and curved subsidence of the entire roof. Significant changes in displacement and stress within the coal seam roof were recorded, and these increased during continuous mining activity. Displacement and stress difference on either side of the fault gradually increased and reached remarkable values with increase in mining distance. On the basis of the experiment results, water inrush is believed to be caused by the interaction between mining and the fault, and, as calculated from parameters collected in field investigations, a waterproof coal pillar of 50 m width should be established to prevent Fault Sun activation, thereby reducing the risk of water inrush from neighbouring aquifers.

scholarly journals Determination of cyclic filling length in gob-side entry retained with roadside filling and its application

2020 ◽  
Author(s):  
Zizheng Zhang ◽  
Jianbiao Bai ◽  
Xianyang Yu ◽  
Weijian Yu ◽  
Min Deng ◽  
...  
Keyword(s):  
Coal Seam ◽  
Coal Mine ◽  
Difference Method ◽  
Suggested Method ◽  
Stress Difference ◽  
Thick Coal Seam ◽  
Mechanics Model ◽  
Working Face ◽  
Geological Conditions ◽  
The Relationship

Abstract Gob-side entry retained with roadside filling (GER-RF) plays a key role in achieving coal mining without pillar and improving the coal resource recovery rate. Since there are few reports on the cyclic filling length of GER-RF, a method based on the stress difference method is proposed to determine the cyclic filling length of GER-RF. Firstly, a stability analysis mechanics model of the immediate roof above roadside filling area in GER was established, then the relationship between the roof stress distribution and the unsupported roof length was obtained by the stress difference method. According to the roof stability above roadside filling area based on the relationship between the roof stress and its tensile strength, the maximum unsupported roof length and rational cyclic filling length of GER-RF. Combined with the geological conditions of the 1103 thin coal seam working face of Heilong Coal Mine and the geological conditions of the 1301 thick coal seam working face of Licun Coal Mine, this suggested method was applied to determine that the rational cyclic filling lengths of GER-RF were 2.4 m and 3.2 m, respectively. Field trial tests show that the suggested method can effectively control the surrounding rock deformation along with rational road-in support and roadside support, and improve the filling and construction speed.

scholarly journals Modeling Rock Fracture Propagation and Water Inrush Mechanisms in Underground Coal Mine

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Shichuan Zhang ◽  
Baotang Shen ◽  
Yangyang Li ◽  
Shengfan Zhou
Keyword(s):  
Coal Seam ◽  
Coal Mine ◽  
Rock Fracture ◽  
Water Inrush ◽  
Water Channel ◽  
Karst Collapse ◽  
Mining Equipment ◽  
Geological Conditions ◽  
Fracturing Process ◽  
Collapse Column

Water inrush in underground mines is a major safety threat for mining personnel, and it can also cause major damage to mining equipment and result in severe production losses. Water inrush can be attributed to the coalescence of rock fractures and the formation of water channel in rock mass due to the interaction of fractures, hydraulic flow, and stress field. Hence, predicting the fracturing process is the key for investigating the water inrush mechanisms for safe mining. A new coupling method is designed in FRACOD to investigate the mechanisms of water inrush disaster (known as “Luotuoshan accident”) which occurred in China in 2010 in which 32 people died. In order to investigate the evolution processes and mechanisms of water inrush accident in Luotuoshan coal mine, this study applies the recently developed fracture-hydraulic (F-H) flow coupling function to FRACOD and focuses on the rock fracturing processes in a karst collapse column which is a geologically altered zone linking several rock strata vertically formed by the long-term dissolution of the flowing groundwater. The numerical simulation of water inrush is conducted based on the actual geological conditions of Luotuoshan mining area, and various materials with actual geological characteristics were used to simulate the rocks surrounding the coal seam. The influences of several key factors, such as in situ stresses, fractures on the formation, and development of water inrush channels, are investigated. The results indicate that the water inrush source is the Ordovician limestone aquifer, which is connected by the karst collapse column to No. 16 coal seam; the fracturing zone that led to a water inrush occurs in front of the roadway excavation face where new fractures coalesced with the main fractured zone in the karst collapse column.

Numerical Analysis for the Influence of Mining Deep Coal Seam on Oversize Normal Fault

2014 ◽  
Vol 1073-1076 ◽  
pp. 2112-2116
Author(s):  
Xin Xian Zhai ◽  
Shi Wei Zhang ◽  
She Jun Ma ◽  
Guang Sen Li
Keyword(s):  
Coal Seam ◽  
Abutment Pressure ◽  
Water Inrush ◽  
Coal Pillar ◽  
Normal Fault ◽  
Mine Safety ◽  
Coal Face ◽  
Safety Production ◽  
Floor Water Inrush ◽  
The Stability

The F2 fault Guo in Tianyu Coal Mine belongs to the oversize normal fault, and mining deep coal seam has an influence on the floor water-inrush. Therefore, study the reasonable width of the fault protected coal pillar is a great significance for the mine safety production. With different advance distances of coal face into the fault hangingwall, the authors, by FLAC numerical calculation, studied the characteristics of plastic zone and stress field in front of the coal face. The results show that influence zone scope of moving abutment pressure is about 70~ 80m. The fault is still in the pressure-relief area when it is in the moving abutment pressure zone. The conclusion is conducive to the stability of F2 fault Guo, to prevent the floor from water-inrush, when the reasonable coal pillar width of the fault is wider than 80m.

scholarly journals Research and Application of Directional Roof Cutting and Pressure Releasing Technology for Retracement Channel of 3314 Working Face in Hexi Coal Mine

2021 ◽  
Author(s):  
Jindong Cao ◽  
Xiaojie Yang ◽  
Ruifeng Huang ◽  
Qiang Fu ◽  
Yubing Gao
Keyword(s):  
Coal Mine ◽  
High Stress ◽  
Surrounding Rock ◽  
Engineering Practice ◽  
Mine Pressure ◽  
Working Face ◽  
Geological Conditions ◽  
Cutting Effect ◽  
The Stability ◽  
Two Sides

Abstract The high stress of the surrounding rock of Hexi Coal Mine easily leads to severe deformation of the retracement channel and the appearance of the mine pressure during the retreat severely affects the stability of the roadway. In order to solve the above problems, a roadway surrounding rock control technology is proposed and tested. The bidirectional energy-concentrated tensile blasting technology is used to perform directional cutting to cut off the stress propagation path. Firstly, the deformation mechanism of the roof is analyzed by establishing the deformation mechanical model of the roof of the retracement channel. Then, according to the geological conditions of working face 3314 and theoretical calculation, the key parameters of roof cutting and pressure releasing of retracement channel are determined, and through the numerical analysis of its cutting effect, the length of cutting seam is 11.5m, and the cutting angle is 10°. Finally, a field test is carried out on the retracement channel of 3314 working face to verify the effect of roof cutting. The results show that the deformation of the retracement channel and the main roadway is very small. In the process of connecting the working face and the retracement channel, the maximum roof to floor convergence is 141mm, and the two sides convergence is 79mm. After the hydraulic support was retracted, the maximum roof to floor convergence of the surrounding rock is 37 mm, and the two sides convergence is 33mm. The roof cutting and pressure releasing of the retracement channel ensures the safe evacuation of the equipment and the stability of the main roadway. The cutting effect is obvious for the release of pressure, which is of great significance to engineering practice.

scholarly journals Research on Characteristic Recognition and Dangerous Prevention While Mining through Collapse Column of Pansan Minefield,China

2021 ◽  
Author(s):  
Haitao Xu ◽  
hui yang ◽  
Wenbin Sun ◽  
Lingjun Kong ◽  
Peng Zhang
Keyword(s):  
Coal Seam ◽  
Water Inrush ◽  
Coal Pillar ◽  
Simulation Software ◽  
Coal Seams ◽  
Transient Electromagnetic ◽  
Working Face ◽  
Electromagnetic Detection ◽  
Floor Failure ◽  
Collapse Column

Abstract In order to find out the characteristics of geological isomer exposed in the mining process of 12318 working face in Pansan Mine and grasp its influence law on subsequent coal seams mining, the isomer was firstly determined as the collapse column by means of 3D seismic, transient electromagnetic detection, SYT detection and other methods, and its development characteristics, conductivity and water enrichment were identified.Then FLAC3D numerical simulation software was used to analyze the characteristics of vertical stress and plastic failure zone in different coal seams during mining.Finally, by comparing the ultimate failure depth of floor and the thickness of waterproof layer in the process of each coal seam directly pushing through the collapse column, the risk of water inrush and the prevention are analyzed.The results show that the exposed geological isomer is characterized by weak water-rich collapse column.Under the influence of the mining of the previous coal seam and the activation of the collapse column, the subsequent coal seam is in the low stress area before mining, which increases the floor failure and causes the activation of the collapse column more easily during mining.Coal 5# and 4# can be directly pushed through the collapse column, and coal pillar of sufficient width should be left for coal 1# to prevent the collapse column from activating water inrush.

scholarly journals Force-Fracture Characteristics of the Roof above Goaf in a Steep Coal Seam: A Case Study of Xintie Coal Mine

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Hong-sheng Tu ◽  
Shi-hao Tu ◽  
De-fu Zhu ◽  
Ding-yi Hao ◽  
Kai-jun Miao
Keyword(s):  
Theoretical Analysis ◽  
Coal Seam ◽  
Coal Mine ◽  
Thin Plates ◽  
Support Pressure ◽  
Similar Distribution ◽  
Operational Parameters ◽  
Working Face ◽  
Geological Conditions ◽  
Roof Deformation

After coal is extracted from a working face in a steep coal seam (SCS), the immediate roof tends to cave in and refill the lower part of the goaf. Based on the geological conditions of a work area in a SCS and the characteristics of roof caving, this study proposed a formula for the width of the backfill in the goaf and analyzed the main factors influencing it. Based on the small-deflection theory for elastic thin plates, a working face model was created for the mechanical analysis of the main roof above a SCS before the roof fractures for the first time. Then, a roof deflection equation was derived for the estimation roof deformation under the action of both the load from overlying strata and the support provided by the backfill in the goaf. The theoretical analysis combined with the actual operational parameters at the Zuoqipian working face in #49 seam of Xintie Coal Mine shows that the maximum roof deflection is around 0.8 m and occurs at a location 39 m from the upper end of the working face. Fractures will first develop in the upper sections of the frontal and rear walls of the face and the middle of the upper suspended roof due to tension or shearing and ultimately form an E-shaped pattern. The measured support pressure and the roof deformation obtained by theoretical analysis show a similar distribution pattern, indirectly confirming the accuracy of the theoretical results.

Research on Stability of Overburden Structure around Longwall Mining Face in Steeply Dipping Seam Group

2015 ◽  
Vol 724 ◽  
pp. 100-110
Author(s):  
Shi Guang Ren ◽  
Yong Ping Wu ◽  
Jian Hui Yin
Keyword(s):  
Coal Seam ◽  
Longwall Mining ◽  
Coal Pillar ◽  
Beam Theory ◽  
Coal Seams ◽  
Working Face ◽  
Rock Structure ◽  
Longitudinal Bending ◽  
Mining Face ◽  
The Stability

The steeply dipping seam group is defined by the two or more coal seams ,a pitch between 35°~55°. Using masonry beam theory, longitudinal bending theory and “R-S-F” dynamics control theory built a lower area overburden structure mode. Analysed the stability of low position coal seam. The balance requirement and the strength of the structure which is affected by the caving rock and lower coal roof were given. It easily generates two lower position steps rock structure in inclination along working face. Regular breaking of the second structure is the main reason leads to the imbalance of the structure between upper coal pillar and upper coal mining face.The interaction among multiple coal seam panels and overburden structures is the main reason that causes the rock disaster, the unbalance of the lower area may lead to pushing accident, the imbalance of the upper area can generate shock pressure.

scholarly journals Determination of Cyclic Filling Length in Gob-Side Entry Retained with Roadside Filling and Its Application

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Zizheng Zhang ◽  
Jinlin Xin ◽  
Jianbiao Bai ◽  
Xianyang Yu ◽  
Weijian Yu ◽  
...  
Keyword(s):  
Coal Seam ◽  
Coal Mine ◽  
Difference Method ◽  
Suggested Method ◽  
Stress Difference ◽  
Thick Coal Seam ◽  
Mechanics Model ◽  
Working Face ◽  
Geological Conditions ◽  
The Relationship

Gob-side entry retained with roadside filling (GER-RF) plays a key role in achieving coal mining without pillar and improving the coal resource recovery rate. Since there are few reports on the cyclic filling length of GER-RF, a method based on the stress difference method is proposed to determine the cyclic filling length of GER-RF. Firstly, a stability analysis mechanics model of the immediate roof above the roadside filling area was established, and then, the relationship between the roof stress distribution and the unsupported roof length was obtained by the stress difference method. According to the roof stability above the roadside filling area based on the relationship between the roof stress and its tensile strength, the maximum unsupported roof length and rational cyclic filling length were determined. Combined with the geological conditions of the 1103 thin coal seam working face of Heilong Coal Mine and the 1301 thick coal seam working face of Licun Coal Mine, the suggested method was applied to determine that the rational cyclic filling lengths were 2.4 m and 3.2 m, respectively. Field trial tests show that the suggested method can effectively control the surrounding rock deformation along with rational road-in support and roadside support and improve the filling and construction speed.

scholarly journals Research on the Influence of Slurry Filling on the Stability of Floor Coal Pillars during Mining above the Room-and-Pillar Goaf: A Case Study

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-21
Author(s):  
Zhu Li ◽  
Guorui Feng ◽  
Jiaqing Cui
Keyword(s):  
Plastic Zone ◽  
Coal Mine ◽  
Body Height ◽  
Coal Pillar ◽  
Northwest China ◽  
Engineering Practice ◽  
Working Face ◽  
The Stability ◽  
Safe Mining ◽  
Upward Mining

Room-and-pillar mining is a commonly used mining method in previous practice in northwest China mining area. Due to priority selection of high-quality resources, coal mines in northwest China generally have to face upward mining above goaf. Thus, the stability of a floor coal pillar influenced by mining activities plays an essential role in upward mining above goaf. The results indicated that a floor coal pillar kept stable before coal excavation in the no. 6107 working face in the Yuanbaowan coal mine; however, the plastic zone in the floor coal pillar expanded sharply and the elastic core zone reduced suddenly on the influence of abutment pressure. Finally, the floor coal pillar supported failure. Accordingly, the paper proposed a floor coal pillar reinforcing technique through a grout injection filling goaf area. As physically limited by a different-height filling body on the double sides, the plastic zone scope and horizontal displacement and loading capacity of the floor coal pillar were studied, working out that the critical height of the filling body should be about 6 m which can ensure safe mining when upward mining above goaf. Case practice indicated that the fractures induced by mining in the floor coal pillar, filling body, and floor can be restrained effectively when the filling body height is 6 m, which can ensure floor coal pillar stability and safe mining of the no. 6107 working face in the Yuanbaowan coal mine. The research can provide theoretical and technical guidance for upward mining above goaf and have a critical engineering practice value.

scholarly journals Numerical simulation study of mining process of upper and lower walls of normal and reverse faults

2021 ◽  
Vol 2083 (3) ◽  
pp. 032071
Author(s):  
Bian Zhuang
Keyword(s):  
Coal Seam ◽  
Numerical Models ◽  
Hanging Wall ◽  
Coal Pillar ◽  
Normal Fault ◽  
Reverse Fault ◽  
Coal Seams ◽  
Working Face ◽  
Geological Conditions ◽  
Mining Coal

Abstract Mining coal seams near faults are prone to various mine disasters, and different mining sequences have different effects on coal seam disasters. Under this background, the numerical models of normal fault hanging wall, normal faultfoot wall, reverse fault hanging wall and reverse fault footwall under the same geological conditions are established. It is found that the stress concentration of coal pillar is the largest in the mining process of hanging wall of normal fault and footwall of reverse fault, and the possibility of inducing coal pillar rockburst is the largest. Affected by the fault, the coal pillar abutment stress between the working face and the fault shows an upward trend. When mining the coal seam near the fault, various methods such as hydraulic fracturing should be adopted to reduce the coal pillar abutment stress and reduce the risk of mine disasters.

Sign in / Sign up

Export Citation Format

Share Document