scholarly journals Investigations on Performance and Emission Characteristics of Diesel Engine with Biodiesel (Jatropha Oil) and Its Blends

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Amar Pandhare ◽  
Atul Padalkar
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Exhaust Gas Temperature ◽  
Load Conditions

This paper presents the performance of biodiesel blends in a single-cylinder water-cooled diesel engine. All experiments were carried out at constant speed 1500 rpm and the biodiesel blends were varied from B10 to B100. The engine was equipped with variable compressions ratio (VCR) mechanism. For 100% Jatropha biodiesel, the maximum fuel consumption was 15% higher than that of diesel fuel. The brake thermal efficiency for biodiesel and its blends was found to be slightly higher than that of diesel at various load conditions. The increase in specific fuel consumption ranged from 2.75% to 15% for B10 to B100 fuels. The exhaust gas temperature increased with increased biodiesel blend. The highest exhaust gas temperature observed was 430°C with biodiesel for load conditions 1.5 kW, 2.5 kW, and 3.5 kW, where as for diesel the maximum exhaust gas temperature was 440°C. The CO2emission from the biodiesel fuelled engine was higher by 25% than diesel fuel at full load. The CO emissions were lower with Jatropha by 15%, 13%, and 13% at 1.5 kW, 2.5 kW, and 3.5 kW load conditions, respectively. TheNOxemissions were higher by 16%, 19%, and 20% at 1.5 kW, 2.5 kW, and 3.5 kW than that of the diesel, respectively.

scholarly journals Experimental Investigation of Performance and Emission Characteristics of Mahua Biodiesel in Diesel Engine

2011 ◽  
Vol 2011 ◽  
pp. 1-6 ◽  
Author(s):  
S. Savariraj ◽  
T. Ganapathy ◽  
C. G. Saravanan
Keyword(s):  
Diesel Engine ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Performance And Emission ◽  
Performance And Emissions ◽  
Hc Emissions ◽  
Exhaust Gas Temperature ◽  
Mahua Biodiesel ◽  
No Emissions

Biodiesel derived from nonedible feed stocks such as Mahua, Jatropha, Pongamia are reported to be feasible choices for developing countries including India. This paper presents the results of investigation of performance and emissions characteristics of diesel engine using Mahua biodiesel. In this investigation, the blends of varying proportions of Mahua biodiesel and diesel were prepared, analyzed compared with the performance of diesel fuel, and studied using a single cylinder diesel engine. The brake thermal efficiency, brake-specific fuel consumption, exhaust gas temperatures, Co, Hc, No, and smoke emissions were analyzed. The tests showed decrease in the brake thermal efficiencies of the engine as the amount of Mahua biodiesel in the blend increased. The maximum percentage of reduction in BTE (14.3%) was observed for B-100 at full load. The exhaust gas temperature with the blends decreased as the proportion of Mahua increases in the blend. The smoke, Co, and No emissions of the engine were increased with the blends at all loads. However, Hc emissions of Mahua biodiesels were less than that of diesel.

scholarly journals An Experimental Study on the Performance Characteristics of a Diesel Engine Fueled with ULSD-Biodiesel Blends

2020 ◽  
Vol 10 (2) ◽  
pp. 183-190
Author(s):  
Viet Dung Tran ◽  
Anh Tuan Le ◽  
Anh Tuan Hoang
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Cooling System ◽  
Specific Fuel Consumption ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Exhaust Gas Temperature ◽  
Low Sulfur

As a rule, the highest permissible sulfur content in the marine fuel must drop below 0.5% from 1 January 2020 for global fleets. As such, ships operating in emission control areas must use low sulfur or non-sulfur fuel to limit sulfur emissions as a source of acid rain. However, that fact has revealed two challenges for the operating fleet: the very high cost of ultra-low sulfur diesel (ULSD) and the installation of the fuel conversion system and the ULSD cooling system. Therefore, a solution that blends ULSD and biodiesel (BO) into a homogeneous fuel with properties equivalent to that of mineral fuels is considered to be significantly effective. In the current work, an advanced ultrasonic energy blending technology has been applied to assist in the production of homogeneous ULSD-BO blends (ULSD, B10, B20, B30, and B50 with blends of coconut oil methyl ester with ULSD of 10%, 20%, 30% and 50% by volume) which is supplied to a small marine diesel engine on a dynamo test bench to evaluate the power and torque characteristics, also to consider the effect of BO fuel on specific fuel consumption exhaust gas temperature and brake thermal efficiency. The use of the ultrasonic mixing system has yielded impressive results for the homogeneous blend of ULSD and BO, which has contributed to improved combustion quality and thermal efficiency. The results have shown that the power, torque, and the exhaust gas temperature, decrease by approximately 9%, 2%, and 4% respectively with regarding the increase of the blended biodiesel rate while the specific fuel consumption and brake thermal efficiency tends to increase of around 6% and 11% with those blending ratios.

Performance and Emissions of Jatropha-Palm Blended Biodiesel

2013 ◽  
Vol 393 ◽  
pp. 344-349 ◽  
Author(s):  
Syarifah Yunus ◽  
Amirul Abd Rashid ◽  
Syazuan Abdul Latip ◽  
Nik Rosli Abdullah ◽  
Rizalman Mamat ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Vertical Cylinder ◽  
Biodiesel Fuel ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Fuel Sample ◽  
Performance And Emissions ◽  
Exhaust Gas Temperature ◽  
Load Conditions

This paper deals with performances and emissions of Jatropha-Palm blended biodiesel as fuel for 4-stroke single vertical cylinder diesel engine. Five fuel samples were tested; i) Diesel fuel supplied by Petronas (PDF); ii) 5% of blended Jatropha-Palm biodiesel and 95% Diesel fuel (B5JPB); iii) 10% of blended Jatropha-Palm biodiesel and 90% Diesel fuel (B10JPB); iv) 15% of blended Jatropha-Palm biodiesel and 85% Diesel fuel (B15JPB); and v) 20% of blended Jatropha-Palm biodiesel and 80% Diesel fuel (B20JPB). Engine performances (specific fuel consumption, brake thermal efficiency) and emissions (exhaust gas temperature and Nox emission) were analyzed and have been discussed in this study. All tests were carried out at varied load conditions which were 0.13, 0.15, 0.17, 0.19 and 0.21 kW. The results revealed that B10JPB blended showed better engine performances compared to its other blends and comparable performances compared to PDF. Comparable Nox emitted of all Jatropha-Palm fuel blended biodiesel fuel sample has been demonstrated to those PDF.

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

Design and Development of Surge Tank for NOx Emission Reduction in B20 Biofueled Diesel Engine

2020 ◽  
Vol 12 (5) ◽  
Author(s):  
Jaspreet Hira ◽  
Basant Singh Sikarwar ◽  
Rohit Sharma ◽  
Vikas Kumar ◽  
Prakhar Sharma
Keyword(s):  
Diesel Engine ◽  
Research Work ◽  
Engine Performance ◽  
Nox Emission ◽  
Intake Manifold ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Surge Tank ◽  
Brake Thermal Efficiency ◽  
Exhaust Gas Temperature

In this research work, a surge tank is developed and utilised in the diesel engine for controlling the NOX emission. This surge tank acts as a damper for fluctuations caused by exhaust gases and also an intercooler in reducing the exhaust gas temperature into the diesel engine intake manifold. With the utilisation of the surge tank, the NOX emission level has been reduced to approximately 50%. The developed surge tank is proved to be effective in maintaining the circulation of water at appropriate temperatures. A trade-off has been established between the engine performance parameters including the brake thermal efficiency, brake specific fuel consumption, exhaust gas temperature and all emission parameters including HC and CO.

The Comparative Trail Research on the Performance of a Diesel Engine Fuelled with Diesel Fuel and Biodiesel/Diesel Blended Fuel

2011 ◽  
Vol 142 ◽  
pp. 103-106
Author(s):  
Wen Ming Cheng ◽  
Hui Xie ◽  
Gang Li
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Series Of Experiments ◽  
Blended Fuel ◽  
Load Conditions

This paper discusses the brake specific fuel consumption and brake thermal efficiency of a diesel engine using cottonseed biodiesel blended with diesel fuel. A series of experiments were conducted for the various blends under varying load conditions at a speed of 1500 rpm and 2500 rpm and the results were compared with the neat diesel. From the results, it is found that the brake specific fuel consumption of cottonseed biodiesel is slightly higher than that of diesel fuel at different engine loads and speeds, with this increase being higher the higher the percentage of the biodiesel in the blend. And the brake thermal efficiency of cottonseed biodiesel is nearly similar to that of diesel fuel at different engine loads and speeds. From the investigation, it is concluded that cottonseed biodiesl can be directly used in diesel engines without any modifications, at least in small blending ratios.

scholarly journals Computational model of the fuel consumption and exhaust temperature of a heavy duty diesel engine using MATLAB/SIMULINK

2020 ◽  
Vol 45 (4) ◽  
pp. 51-70
Author(s):  
Ifeanyi Dilibe
Keyword(s):  
Control System ◽  
Diesel Engine ◽  
Fuel Consumption ◽  
Exhaust Gas ◽  
Electronic Control ◽  
Gas Temperature ◽  
Brake Torque ◽  
Exhaust Temperature ◽  
Electronic Control System ◽  
Exhaust Gas Temperature

A model of a diesel engine and its electronic control system was developed to investigate the engine behaviour in a vehicle simulation environment. The modelled quantities were brake torque, fuel consumption and exhaust gas temperature and were based on engine speed and pedal position. In order to describe these outputs the inlet air flow and boost pressure were also modelled and used as inner variables. The model was intended to be implemented on board a vehicle in a control unit which had limited computational performance. To keep the model as computationally efficient as possible the model basically consists of look-up tables and polynomials. First order systems were used to describe the dynamics of air flow and exhaust temperature. The outputs enable gear shift optimization over three variables, torque for vehicle acceleration, fuel consumption for efficiency and exhaust temperature to maintain high efficiency in the exhaust after treatment system. The engine model captures the low frequent dynamics of the modelled quantities in the closed loop of the engine and its electronic control system. The model only consists of three states, one for the pressure build up in the intake manifold and two states for modelling the exhaust temperature. The model was compared to measured data from an engine test cell (as got in INNOSON NIG. LTD.) and the mean absolute relative error were lower than 6.8%, 7.8% and 5.8% for brake torque, fuel consumption and exhaust gas temperature respectively. These results were considered good given the simplicity of the model.

Performance and Emission Characteristics of a Mixed Biodiesel Fueled CI Engine

2015 ◽  
Vol 766-767 ◽  
pp. 557-561
Author(s):  
S. Arunprasad ◽  
Thangavel Balusamy ◽  
S. Sivalakshmi
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Emission Characteristics ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Ci Engine ◽  
Smoke Opacity

In this present paper, an attempt has been made to examine the performance and emission characteristics of a single cylinder diesel engine fueled with blends of mixed biodiesel (Thevetia peruviana, Neem, Jatropha, Pongamia). Experiments were conducted with various blends of mixed biodiesel in CI engine for different loads. The results show that lower brake thermal efficiency and higher brake specific fuel consumption were obtained with mixed biodiesel blends when compared with diesel. Lower the value of CO and HC and higher the value of CO2 emissions were determined for mixed biodiesel blends compared to that of diesel. Also, higher in NOx and lower smoke opacity were found compared to diesel.

An Experimental Study on the Performance and Emission Characteristics of Jatropha Biodiesel Fuelled CI Engine

2009 ◽  
Author(s):  
Samiddha Palit ◽  
Bijan Kumar Mandal ◽  
Sudip Ghosh ◽  
Arup Jyoti Bhowal
Keyword(s):  
Diesel Fuel ◽  
Combustion Process ◽  
Maximum Efficiency ◽  
Emission Characteristics ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Biodiesel Blends ◽  
Full Load ◽  
Fuel Blends ◽  
Exhaust Gas Temperature

A twin cylinder, constant speed, direct injection CI (diesel) engine was run on jatropha biodiesel and diesel fuel blends. The engine was directly coupled to a hydraulic dynamometer whose load was varied by adjusting load wheel on the top of the engine. The test results were recorded for pure diesel, pure biodiesel (B100) and different diesel/biodiesel blends. The performance characteristics shows that brake specific fuel consumption (BSFC) decreases rapidly with increase of load up to 4.0 to 4.5 kW (55% to 62% of full load) and then decreases slowly. This result also indicates that BSFC increases when the percentage of biodiesel in the blends is increased. Brake thermal efficiency also increases from high biodiesel blends to pure diesel fuel. Each fuel curve shows maximum efficiency reaches at the load range of 5.0 to 5.5 kW (68% to 75% of full load). Pure diesel has maximum efficiency 29.6%, where as pure biodiesel has maximum efficiency of 21.2%. The exhaust gas temperature increases with the load for all fuel blends. Pure biodiesel gives higher exhaust temperature (320°C) than pure diesel (260°C). The exhaust gas temperature increases with the higher percentage of biodiesel blends in different fuel blends. The probable reason for that is biodiesel contains oxygen atoms which make the combustion process complete and hence more energy is released. In respect of emission characteristics, carbon mono-oxide (CO) and hydrocarbon emissions are improved with the addition of biodiesel to diesel. But these emissions increase with the increase of load for all fuel blends. NOx emission increases with load as well as percentage of blending of biodiesel in the diesel fuel.

scholarly journals THE EFFECT OF ISO‐BUTANOL‐DIESEL BLENDS ON ENGINE PERFORMANCE

Transport ◽  
2008 ◽  
Vol 23 (4) ◽  
pp. 306-310 ◽  
Author(s):  
Mohammad Ibrahim Al-Hasan ◽  
Muntaser Al-Momany
Keyword(s):  
Diesel Fuel ◽  
Engine Performance ◽  
Exhaust Gas ◽  
Performance Parameters ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Fuel Blends ◽  
Ci Engine ◽  
Exhaust Gas Temperature ◽  
Better Than

The effect of iso‐butanol addition to diesel fuel on engine performance parameters has been experimentally investigated. The used engine was a single cylinder four stroke CI engine Type Lister 1–8. The tests were performed at engine speed that ranges from 375 to 625 with an increment of 42 rpm at different loads and with 10, 20, 30 and 40% v/v iso‐butanol‐diesel fuel blends. The overall engine performance parameters measured included air‐fuel ratio (AFR), exhaust gas temperature, brake power (Bp ), brake specific fuel consumption (bsfc) and brake thermal efficiency (η th ). The experimental results show that AFR, exhaust gas temperature, (Bp ) and (ηbth ) decreased and bsfc increased with iso‐butanol addition compared to net diesel fuel. Also, the obtained results indicate that the engine performance parameters when using up to 30% iso‐butanol in fuel blends are better than that of 40%.

Sign in / Sign up

Export Citation Format

Share Document