scholarly journals Computational model of the fuel consumption and exhaust temperature of a heavy duty diesel engine using MATLAB/SIMULINK

2020 ◽  
Vol 45 (4) ◽  
pp. 51-70
Author(s):  
Ifeanyi Dilibe
Keyword(s):  
Control System ◽  
Diesel Engine ◽  
Fuel Consumption ◽  
Exhaust Gas ◽  
Electronic Control ◽  
Gas Temperature ◽  
Brake Torque ◽  
Exhaust Temperature ◽  
Electronic Control System ◽  
Exhaust Gas Temperature

A model of a diesel engine and its electronic control system was developed to investigate the engine behaviour in a vehicle simulation environment. The modelled quantities were brake torque, fuel consumption and exhaust gas temperature and were based on engine speed and pedal position. In order to describe these outputs the inlet air flow and boost pressure were also modelled and used as inner variables. The model was intended to be implemented on board a vehicle in a control unit which had limited computational performance. To keep the model as computationally efficient as possible the model basically consists of look-up tables and polynomials. First order systems were used to describe the dynamics of air flow and exhaust temperature. The outputs enable gear shift optimization over three variables, torque for vehicle acceleration, fuel consumption for efficiency and exhaust temperature to maintain high efficiency in the exhaust after treatment system. The engine model captures the low frequent dynamics of the modelled quantities in the closed loop of the engine and its electronic control system. The model only consists of three states, one for the pressure build up in the intake manifold and two states for modelling the exhaust temperature. The model was compared to measured data from an engine test cell (as got in INNOSON NIG. LTD.) and the mean absolute relative error were lower than 6.8%, 7.8% and 5.8% for brake torque, fuel consumption and exhaust gas temperature respectively. These results were considered good given the simplicity of the model.

scholarly journals An Experimental Study on the Performance Characteristics of a Diesel Engine Fueled with ULSD-Biodiesel Blends

2020 ◽  
Vol 10 (2) ◽  
pp. 183-190
Author(s):  
Viet Dung Tran ◽  
Anh Tuan Le ◽  
Anh Tuan Hoang
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Cooling System ◽  
Specific Fuel Consumption ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Exhaust Gas Temperature ◽  
Low Sulfur

As a rule, the highest permissible sulfur content in the marine fuel must drop below 0.5% from 1 January 2020 for global fleets. As such, ships operating in emission control areas must use low sulfur or non-sulfur fuel to limit sulfur emissions as a source of acid rain. However, that fact has revealed two challenges for the operating fleet: the very high cost of ultra-low sulfur diesel (ULSD) and the installation of the fuel conversion system and the ULSD cooling system. Therefore, a solution that blends ULSD and biodiesel (BO) into a homogeneous fuel with properties equivalent to that of mineral fuels is considered to be significantly effective. In the current work, an advanced ultrasonic energy blending technology has been applied to assist in the production of homogeneous ULSD-BO blends (ULSD, B10, B20, B30, and B50 with blends of coconut oil methyl ester with ULSD of 10%, 20%, 30% and 50% by volume) which is supplied to a small marine diesel engine on a dynamo test bench to evaluate the power and torque characteristics, also to consider the effect of BO fuel on specific fuel consumption exhaust gas temperature and brake thermal efficiency. The use of the ultrasonic mixing system has yielded impressive results for the homogeneous blend of ULSD and BO, which has contributed to improved combustion quality and thermal efficiency. The results have shown that the power, torque, and the exhaust gas temperature, decrease by approximately 9%, 2%, and 4% respectively with regarding the increase of the blended biodiesel rate while the specific fuel consumption and brake thermal efficiency tends to increase of around 6% and 11% with those blending ratios.

scholarly journals Investigations on Performance and Emission Characteristics of Diesel Engine with Biodiesel (Jatropha Oil) and Its Blends

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Amar Pandhare ◽  
Atul Padalkar
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Exhaust Gas Temperature ◽  
Load Conditions

This paper presents the performance of biodiesel blends in a single-cylinder water-cooled diesel engine. All experiments were carried out at constant speed 1500 rpm and the biodiesel blends were varied from B10 to B100. The engine was equipped with variable compressions ratio (VCR) mechanism. For 100% Jatropha biodiesel, the maximum fuel consumption was 15% higher than that of diesel fuel. The brake thermal efficiency for biodiesel and its blends was found to be slightly higher than that of diesel at various load conditions. The increase in specific fuel consumption ranged from 2.75% to 15% for B10 to B100 fuels. The exhaust gas temperature increased with increased biodiesel blend. The highest exhaust gas temperature observed was 430°C with biodiesel for load conditions 1.5 kW, 2.5 kW, and 3.5 kW, where as for diesel the maximum exhaust gas temperature was 440°C. The CO2emission from the biodiesel fuelled engine was higher by 25% than diesel fuel at full load. The CO emissions were lower with Jatropha by 15%, 13%, and 13% at 1.5 kW, 2.5 kW, and 3.5 kW load conditions, respectively. TheNOxemissions were higher by 16%, 19%, and 20% at 1.5 kW, 2.5 kW, and 3.5 kW than that of the diesel, respectively.

Effect of Fuel Injection Strategy on DPF Regeneration in Single Cylinder Diesel Engine

2015 ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Experimental Results ◽  
Exhaust Gas ◽  
Post Injection ◽  
Gas Temperature ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) force automotive manufacturers to equip DPF (diesel particulate filter) on diesel cars. Generally, post injection is used as a method to regenerate DPF. However, it is known that post injection deteriorates specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration becomes one of key technologies for diesel powertrain equipped with a DPF. This paper presents correlations between fuel injection strategy and exhaust gas temperature for DPF regeneration. Experimental apparatus consists of a single cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, post injection timing covers from 40 deg aTDC to 110 deg aTDC and double post injection was considered. In addition, effects of injection pressures were investigated. The engine load was varied from low-load to mid-load and fuel amount of post injection was increased up to 10mg/stk. Oil dilution during fuel injection and combustion processes were estimated by diesel loss measured by comparing two global equivalences ratios; one is measured from Lambda sensor installed at exhaust port, the other one is estimated from intake air mass and injected fuel mass. In the present study, the differences in global equivalence ratios were mainly caused from oil dilution during post injection. The experimental results of the present study suggest an optimal engine operating conditions including fuel injection strategy to get appropriate exhaust gas temperature for DPF regeneration. Experimental results of exhaust gas temperature distributions for various engine operating conditions were summarized. In addition, it was revealed that amounts of oil dilution were reduced by splitting post injection (i.e., double post injection). Effects of injection pressure on exhaust gas temperature were dependent on combustion phasing and injection strategies.

scholarly journals Late Fuel Post-Injection Influence on the Dynamics and Efficiency of Wall-Flow Particulate Filters Regeneration

2019 ◽  
Vol 9 (24) ◽  
pp. 5384 ◽  
Author(s):  
José Ramón Serrano ◽  
Pedro Piqueras ◽  
Joaquín de la Morena ◽  
Enrique José Sanchis
Keyword(s):  
Fuel Consumption ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Post Injection ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Particulate Filters ◽  
Exhaust Temperature ◽  
Injection Parameters ◽  
Wall Flow

Late fuel post-injections are the most usual strategy to reach high exhaust temperature for the active regeneration of diesel particulate filters. However, it is important to optimise these strategies in order to mitigate their negative effect on the engine fuel consumption. This work aims at understanding the influence of the post-injection parameters, such as its start of injection and its fuel quantity, on the duration of the regeneration event and the fuel consumption along it. For this purpose, a set of computational models are employed to figure out in a holistic way the involved phenomena in the interaction between the engine and the exhaust gas aftertreatment system. Firstly, an engine model is implemented to evaluate the effect of the late fuel post-injection pattern on the gas properties at the exhaust aftertreatment system inlet in different steady-state operating conditions. These are selected to provide representative boundary conditions of the exhaust gas flow concerning dwell time, exhaust temperature and O 2 concentration. In this way, the results are later applied to the analysis of the diesel oxidation catalyst and wall-flow particulate filter responses. The dependence of the diesel particulate filter (DPF) inlet temperature is discussed based on the efficiency of each post-injection strategy to increase the exhaust gas temperature. Next, the influence on the dynamics of the regeneration of the post-injection parameters through the change in gas temperature and O 2 concentration is finally studied distinguishing the pre-heating, maximum reactivity and late soot oxidation stages as well as the required fuel consumption to complete the regeneration process.

scholarly journals A model-based and experimental approach for the determination of suitable variable valve timings for cold start in partial load operation of a passenger car single-cylinder diesel engine

2018 ◽  
Vol 20 (1) ◽  
pp. 141-154 ◽  
Author(s):  
P Maniatis ◽  
U Wagner ◽  
T Koch
Keyword(s):  
Diesel Engine ◽  
Experimental Investigations ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Warm Up ◽  
One Dimensional ◽  
Engine Efficiency ◽  
Residual Gas ◽  
Dimensional Simulation ◽  
Exhaust Gas Temperature

A manipulation of the charge exchange allows controlling the amount of residual gas during engine warm-up. The residual gas during the warm-up phase leads to an increase of the exhaust gas temperature and supports to reach the exhaust after-treatment system operating temperature faster. In addition, the warm residual gas increases the combustion chamber temperature, which reduces the HC and CO emissions. However, fuel consumption increases. For that reason, such heating measures should be the best compromise of both, exhaust gas temperature increase and engine efficiency, in order to provide efficient heating strategies for passenger car diesel engines. Therefore, simulative and experimental investigations are carried out at the Institute of Internal Combustion Engines of the Karlsruhe Institute of Technology to establish a reliable cam design methodology. For the experimental investigations, a modern research single-cylinder diesel engine was set up on a test bench. In addition, a one-dimensional simulation model of the experimental setup was created in order to simulate characteristics of valve lift curves and to investigate their effects on the exhaust gas temperature and the exhaust gas enthalpy flow. These simulations were based on design of experiments (DoE), so that all characteristics can be used sustainably for modeling and explaining their influences on the engine operation. This methodology allows numerically investigating promising configurations and deriving cam contours which are manufactured for testing. To assess the potential of these individual configurations, the results obtained were compared with each other as well as with the series configuration. Results show that the combination of DoE and one-dimensional simulation for the design of camshaft contours is well suited which was also validated with experimental results. Furthermore, the potential of residual gas retention by favorable configurations with a second event already revealed in various publications could be confirmed with respect to exhaust gas temperature increase and engine efficiency.

Assessment of a Syngas-Diesel Dual Fuelled Compression Ignition Engine

2010 ◽  
Author(s):  
Bibhuti B. Sahoo ◽  
Niranjan Sahoo ◽  
Ujjwal K. Saha
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Gas Flow ◽  
Direct Injection ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Exhaust Gas Temperature

Synthesis gas (Syngas), a mixture of hydrogen and carbon monoxide, can be manufactured from natural gas, coal, petroleum, biomass, and even from organic wastes. It can substitute fossil diesel as an alternative gaseous fuel in compression ignition engines under dual fuel operation route. Experiments were conducted in a single cylinder, constant speed and direct injection diesel engine fuelled with syngas-diesel in dual fuel mode. The engine is designed to develop a power output of 5.2 kW at its rated speed of 1500 rpm under variable loads with inducted syngas fuel having H2 to CO ratio of 1:1 by volume. Diesel fuel as a pilot was injected into the engine in the conventional manner. The diesel engine was run at varying loads of 20, 40, 60, 80 and 100%. The performance of dual fuel engine is assessed by parameters such as thermal efficiency, exhaust gas temperature, diesel replacement rate, gas flow rate, peak cylinder pressure, exhaust O2 and emissions like NOx, CO and HC. Dual fuel operation showed a decrease in brake thermal efficiency from 16.1% to a maximum of 20.92% at 80% load. The maximum diesel substitution by syngas was found 58.77% at minimum exhaust O2 availability condition of 80% engine load. The NOx level was reduced from 144 ppm to 103 ppm for syngas-diesel mode at the best efficiency point. Due to poor combustion efficiency of dual fuel operation, there were increases in CO and HC emissions throughout the range of engine test loads. The decrease in peak pressure causes the exhaust gas temperature to rise at all loads of dual fuel operation. The present investigation provides some useful indications of using syngas fuel in a diesel engine under dual fuel operation.

Performance Characteristics of a Diesel Engine Fueled With Avio-Kerosene

2003 ◽  
Author(s):  
Giancarlo Chiatti ◽  
Ornella Chiavola
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Power Output ◽  
Pressure Rise ◽  
Experimental Tests ◽  
Diesel Oil ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Exhaust Gas Temperature

A comparative series of experimental tests has been performed on a 4-stroke multi cylinder indirect injection diesel engine fueled with diesel oil, pure gas-turbine fuel and gas-turbine fuel with additives. The engine has been equipped aimed at monitoring both the overall performances and the variation with time of the pressure in the pre-combustion chamber. Some key parameters have been investigated at different engine speeds and loads (ignition delay, pressure rise in the pre-combustion chamber, power output, specific fuel consumption, exhaust gas temperature) and discussed results are presented.

scholarly journals Effects of Specific Fuel Consumption and Exhaust Emissions of Four Stroke Diesel Engine with CuO/Water Nanofluid as Coolant

2017 ◽  
Vol 64 (1) ◽  
pp. 111-121 ◽  
Author(s):  
S. Senthilraja ◽  
KCK. Vijayakumar ◽  
R. Gangadevi
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Load Condition ◽  
Exhaust Emissions ◽  
Cuo Nanoparticles ◽  
Specific Fuel Consumption ◽  
Gas Temperature ◽  
Step Method ◽  
Series Of Experiments ◽  
Exhaust Gas Temperature

Abstract This article reports the effects of CuO/water based coolant on specific fuel consumption and exhaust emissions of four stroke single cylinder diesel engine. The CuO nanoparticles of 27 nm were used to prepare the nanofluid-based engine coolant. Three different volume concentrations (i.e 0.05%, 0.1%, and 0.2%) of CuO/water nanofluids were prepared by using two-step method. The purpose of this study is to investigate the exhaust emissions (NOx), exhaust gas temperature and specific fuel consumption under different load conditions with CuO/water nanofluid. After a series of experiments, it was observed that the CuO/water nanofluids, even at low volume concentrations, have a significant influence on exhaust emissions. The experimental results revealed that, at full load condition, the specific fuel consumption was reduced by 8.6%, 15.1% and 21.1% for the addition of 0.05%, 0.1% and 0.2% CuO nanoparticles with water, respectively. Also, the emission tests were concluded that 881 ppm, 853 ppm and 833 ppm of NOx emissions were observed at high load with 0.05%, 0.1% and 0.2% volume concentrations of CuO/water nanofluids, respectively.

Sign in / Sign up

Export Citation Format

Share Document