scholarly journals Investigating the Influence of Process Parameters of ZNC EDM on Machinability of A6061/10% SiC Composite

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Balbir Singh ◽  
Jatinder Kumar ◽  
Sudhir Kumar
Keyword(s):  
Thermal Analysis ◽  
Optical Microscopy ◽  
Process Parameters ◽  
Al Alloy ◽  
Machining Parameters ◽  
Machining Performance ◽  
X Ray ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

A6061/10% SiC composite has been fabricated by mechanical stir casting process. Fabricated composite has also been characterized through optical microscopy, X-ray diffraction analysis (XRD), scanning electron microscopy analysis (SEM) with energy dispersive X-ray techniques (EDX), and thermogravimetric/differential thermal analysis (TG/DTA). The composite has been experimentally investigated for its machinability usingZ-axis numerically controlled (ZNC) electrodischarge machining (EDM) process. The effects of the four process parameters, namely, current, gap voltage, pulse-on time, and pulse-off time are investigated on material removal rate (MRR), tool wear rate (TWR), and surface roughness (SR) by varying one parameter at a time approach. Optical microscopy and SEM analysis revealed the uniform distribution of SiC particles in aluminum matrix phase. XRD investigation corroborated the elemental composition of 6061 Al alloy and reinforcement particles. Thermal analysis shows stability of composite upto 650°C. The machinability characteristics, namely, MRR, TWR, and SR have been interpreted using graphical representations. The study indicates that all the machining parameters affect the machining performance of A6061/10% SiC composite. Optimum machining performance has been realized at the lower setting of current and pulse-on time and the optimum setting of pulse-off time and gap voltage.

Experimental Investigation of Process Parameters in Wire Electrical Discharge Machining by Response Surface Methodology on IS2062 Steel

2014 ◽  
Vol 550 ◽  
pp. 53-61
Author(s):  
R.Arun Bharathi ◽  
P.Ashoka Varthanan ◽  
K. Manoj Mathew
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Process Parameters ◽  
Machining Parameters ◽  
Peak Current ◽  
Custom Design ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

The objective of the present work is to predict the optimal set of process parameters such as peak current (IP), pulse on/off time (TON/TOFF) and spark gap voltage (SV) to achieve minimum Surface roughness (Ra), wire consumption rate (WCR) and maximum material removal rate (MRR). In this work, experiments were carried out by pulse arc discharges generated between ZnO coated brass wire and specimen (IS2062 steel) suspended in deionized water dielectric. The experiments were designed based on the above mentioned four factors, each having three levels. Custom design based Response Surface Methodology (RSM) is used in this research. 21 runs of experiments were constructed based on custom design procedure and results of the experimentation were analyzed analytically as well as graphically. Moreover the surface roughness after machining was measured by Taylor Hobson Surtronic device. Second order regression model has been developed for predicting Ra, WCR and MRR in terms of interactive and higher order machining parameters through RSM, utilizing relevant experimental data as obtained through experimentation. The research outcome identifies significant parametersand their effect on process performance on IS2062 steel. The results revealed that peak current, pulse on-time and their interactions have significant effects on Ra, whereas pulse off time and peak current have significant effects on MRR and it is also observed that peak current and interaction between peak current and pulse off time have significant effects on WCR. The adequacy of the above proposed models has been tested through the analysis of variance (ANOVA).

scholarly journals Effects of Side Flushing and Multi-Aperture Inner Flushing on Characteristics of Electrical Discharge Machining Macro Deep Holes

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 148
Author(s):  
Suppawat Chuvaree ◽  
Kannachai Kanlayasiri
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Machining Performance ◽  
Electrode Rotation ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

This research investigates the effect of machining parameters on material removal rate, electrode wear ratio, and gap clearance of macro deep holes with a depth-to-diameter ratio over four. The experiments were carried out using electrical discharge machining with side flushing and multi-aperture flushing to improve the machining performance and surface integrity. The machining parameters were pulse on-time, pulse off-time, current, and electrode rotation. Response surface methodology and the desirability function were used to optimize the electrical discharge machining parameters. The results showed that pulse on-time, current, and electrode rotation were positively correlated with the material removal rate. The electrode wear ratio was inversely correlated with pulse on-time and electrode rotation but positively correlated with current. Gap clearance was positively correlated with pulse on-time but inversely correlated with pulse off-time, current, and electrode rotation. The optimal machining condition of electrical discharge machining with side flushing was 100 µs pulse on-time, 20 µs pulse off-time, 15 A current, and 70 rpm electrode rotation; and that of electrical discharge machining with multi-aperture flushing was 130 µs, 2 µs, 15 A, and 70 rpm. The novelty of this research lies in the use of multi-aperture flushing to improve the machining performance, enable a more uniform GC profile, and minimize the incidence of recast layer.

scholarly journals Analysis of Machining Parameters in WEDM of Al/SiCp20 MMC Using Taguchi-Based Grey-Fuzzy Approach

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Mangesh R. Phate ◽  
Shraddha B. Toney ◽  
Vikas R. Phate
Keyword(s):  
Process Parameters ◽  
Feed Rate ◽  
Machining Parameters ◽  
Peak Current ◽  
Experimental Findings ◽  
Grey Relational ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Wire Feed

Aluminium silicate metal matrix composite (AlSiC MMC) is satisfying the requirement of material with good mechanical, thermal properties, and good wear resistance. But the difficulties during the machining are the main hurdles to its replacement for other materials. Wire electric discharge machining (WEDM) is a very effective process used for this type of difficult-to-cut material. So an effort has been taken to find out the most favourable level of input parameters for WEDM of AlSiC (20%) composite using a Taguchi-based hybrid grey-fuzzy grade (GFG) approach. The plan for experimentation is designed using Taguchi’s L9 (23) array. The various process parameters considered for the investigation are pulse on time (TON), pulse off time (TOFF), wire feed rate (WFR), and peak current (IP). Surface integrity such as surface roughness measured during the different types of cutting (along straight, inclined, and curvature directions) is considered in the present work. Grey relational analysis (GRA) pooled with the fuzzy logic is effectively used to find out the grey-fuzzy reasoning grade (GFRG). The Taguchi approach is coupled with the GFRG to obtain the optimum set of process parameters. From the experimental findings, it has been observed that the most economical process parameters for WEDM of AlSiCp20 were the pulse on time is 108 microsec, pulse off time is 56 microsec, wire feed rate (WFR) is 4 m/min, and peak current (IP) is 11 amp. From the analysis of variance (ANOVA), it is observed that the pulse on time is the foremost influencing parameters that contribute towards GFRG by 52.61%, followed by the wire feed rate (WFR) 38.32% and the current by 5.45%.

Investigations of the Effect of Parameters on the CR and SR during Al6063/SiC/Ti at WEDM

2019 ◽  
Vol 895 ◽  
pp. 181-186
Author(s):  
Rajesh Khanna ◽  
Neeraj Sharma ◽  
Rahul Dev Gupta
Keyword(s):  
Machine Tool ◽  
Process Parameters ◽  
Limited Range ◽  
Machining Process ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Wire Feed ◽  
Time Pulse

Wire electric discharge machine (WEDM) is a non-conventional machining process used to machine the hard to cut materials. WEDM has wide applications in die and punch industries, automobile, aerospace and medical industries. In this process the material is processed with the help of a wire electrode. In present work, Al6063/SiC/Ti composite was processed with the help of WEDM. As this spark-erosion machine tool have number of input process parameters, so to process any material it became mandatory to investigate the range of the machining parameters in which machine tool operate successfully. Every material represents its unique material characteristics due to which it can be machined successfully in a limited range of the parameters. Above and below this range the wire will break abruptly. So, in this present work an attempt has been made to investigate the range of the process parameters in which WEDM can process Al6063/SiC/Ti composite efficiently. The input parameters considered for the present work are pulse on-time, pulse off-time, servo voltage, peak current, wire feed and wire tension. After the experiments it was found that the pulse on-time, pulse off-time, servo voltage and wire-feed were the significant process parameters in the investigations of cutting rate and surface roughness.

Mathematical Modeling of Machining Parameters in Electrical Discharge Machining with Cu-B4C Composite Electrode

2012 ◽  
Vol 488-489 ◽  
pp. 871-875
Author(s):  
V. Anandakrishnan ◽  
V. Senthilkumar
Keyword(s):  
Mathematical Models ◽  
Current Pulse ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Selection Of

Copper based metal matrix composite reinforced with Boron Carbide is a newly developed Electrical Discharge Machining (EDM) electrode showing better performance than the conventional copper based electrode. Right selection of machining parameters such as current, pulse on time and pulse off time is one of the most important aspects in EDM. In this paper an attempt has been made to develop mathematical models for relating the Material Removal Rate (MRR), Tool Removal Rate (TRR) and Surface roughness (Ra) to machining parameters (current, pulse-on time and pulse-off time). Furthermore, a study was carried out to analyze thSubscript texte effects of machining parameters on various performance parameters such as, MRR, TRR and Ra. The results of Analysis of Variance (ANOVA) indicate that the proposed mathematical models, can adequately describe the performance within the limits of the factors being studied. Response surface modeling is used to develop surface and contour graphs to analyze the effects of EDM input parameters on outer parameters.

scholarly journals Study of wire-electrical discharge machining parameters of titanium alloy by using taguchi method

2018 ◽  
Vol 7 (2.8) ◽  
pp. 10
Author(s):  
A VS Ram Prasad ◽  
Koona Ramji ◽  
B Raghu Kumar
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Process Parameters ◽  
Optimization Technique ◽  
Machining Process ◽  
Machining Parameters ◽  
Wire Edm ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Edm Process

Machining of Titanium alloys is difficult due to their chemical and physical properties namely excellent strength, chemical reactivity and low thermal conductivity. Traditional machining of such materials leads to formation of continuous chips and tool bits are subjected to chatter which leads to formation of poor surface on machined surface. In this study, Wire-EDM one of the most popular unconventional machining process which was used to machine such difficult-to-cut materials. Effect of Wire-EDM process parameters namely peak current, pulse-on- time, pulse-off-time, servo voltage on MRRand SR was investigated by Taguchi method. 0.25 mm brass wire was used in this process as electrode material. A surface roughness tester (Surftest 301) was used to measure surface roughness value of the machined work surface. A multi-response optimization technique was then utilized to optimize Wire-EDM process parameters for achieving maximum MRR and minimum SR simultaneously.

scholarly journals Findings of performance evaluation of EDM for different materials of electrodes and work pieces- a review

2018 ◽  
Vol 7 (4.5) ◽  
pp. 542
Author(s):  
Harshalkumar R. Mundane ◽  
Dr. A. V. Kale ◽  
Dr. J. P. Giri
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Performance Measure ◽  
Machining Process ◽  
Machining Parameters ◽  
Spark Erosion ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Time Pulse

EDM (Spark erosion) is non-conventional machining process which uses as removing unwanted material by electrical spark erosion. EDM Machining parameters affecting to the performance and the industries goal is to produce high quality of product with less time consuming and cost. To achieve these goals, optimizing the machining parameters such as pulse on time, pulse off time, cutting speed, depth of cut, duty cycle, arc gap, voltage etc. The performance measure of EDM is calculated on the basis of Material Remove Rate(MRR), Tool Wear Rate(TWR), and Surface Roughness(SR).The main objective of present work is to investigate of the influence of input EDM (Electro Discharge Machining) parameters on machining characteristics like surface roughness and the effects of various EDM process parameters such as pulse on time, pulse off time, servo voltage, peak current, dielectric flow rate, on different process response parameters such as material removal rate (MRR), surface roughness (Ra), Kerf (width of Cut), tool wear ratio(TWR)and surface integrity factors. In this paper few selected research paper related to Die-sinker EDM with effect of MRR, TWR, surface roughness (SR) and work piece material have been discussed.   

Multiple Performance Optimization in WEDM Parameters Using Grey Relational Analysis

2015 ◽  
Vol 813-814 ◽  
pp. 357-361
Author(s):  
T. Rajmohan ◽  
Gopi Krishna ◽  
Ankit Kumar Singh ◽  
A.P.V. Swamy Naidu
Keyword(s):  
Grey Relational Analysis ◽  
Performance Characteristics ◽  
304L Stainless Steel ◽  
Machining Parameters ◽  
Relational Analysis ◽  
Grey Relational ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process ◽  
Off Time

In this investigation, a new approach is based on Grey Relational Analysis and Taguchi method to optimize the machining parameters with multi performance characteristics in WEDM of 304L SS. Experiments are conducted using Taguchi Quality Concept, L9,3-level orthogonal array was chosen for experiments .The WEDM parameters namely pulse-on time (TON), pulse-off time (TOFF), and wire feed (WF) on material removal rate (MRR) .The Grey Relational Analysis with multiple performance characteristics indicates that the pulse-on time (TON), pulse-off time (TOFF) are the most significant factors . The optimum machining parameters have been identified by Grey relational analysis and significant contribution of parameters can be determined by analysis of variance (ANOVA). The confirmation test is also conducted to validate the test result. The results from this study will be useful for manufacturing engineers to select appropriate WEDM process parameters to machine 304L Stainless Steel.

A Comparison of the Effects of Wire Electrical Discharge Machining Parameters on the Processing of Traditionally Manufactured and Additively Manufactured 316L Stainless Steel Specimens

2018 ◽  
Author(s):  
Gregory Bicknell ◽  
Guha Manogharan
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
316L Stainless Steel ◽  
Machining Parameters ◽  
Wire Edm ◽  
Machining Time ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Time Pulse

Wire electric discharge machining (EDM) is a non-traditional machining method that has the ability to machine hard, conductive materials, with no force and high precision. This technology is used in industries, like the aerospace industry, to create precision parts used in high stress applications. Wire EDM is also commonly used in additive manufacturing (AM) applications to remove printed parts from the base-plates onto which they are printed. Numerous studies show the effects of EDM parameters, like pulse-on time, pulse-off time, and cutting voltage, on the processing of traditionally fabricated metal parts. However, very few studies identify how the parameters of wire EDM affect the processing of AM parts. This paper studies the effect of wire EDM pulse-on time, pulse-off time, and cutting voltage on the machining time, surface roughness, and hardness of additively manufactured 316L stainless steel cylinders. The effects of these wire EDM parameters are then tested on the machining time, surface roughness, and hardness of wrought 316L stainless steel cylinders. It was found that machining time of AM samples was statistically significantly lower than wrought samples and also had better surface finish and lower surface hardness.

scholarly journals Multi-Objective Optimization of Wire Electro Discharge Machining (WEDM) Process Parameters Using Grey-Fuzzy Approach

2018 ◽  
Vol 63 (1) ◽  
pp. 16-25 ◽  
Author(s):  
Partha Protim Das ◽  
Sunny Diyaley ◽  
Shankar Chakraborty ◽  
Ranjan Kumar Ghadai
Keyword(s):  
Process Parameters ◽  
Removal Rate ◽  
Machining Process ◽  
Wire Tension ◽  
Electro Discharge Machining ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process ◽  
Fuzzy Logic Technique ◽  
Off Time

Wire electro discharge machining (WEDM) is a versatile non-traditional machining process that is extensively in use to machine the components having intricate profiles and shapes. In WEDM, it is very important to select the optimal process parameters so as to enhance the machine performance. This paper emphasizes the selection of optimal parametric combination of WEDM process while machining on EN31 steel, using grey-fuzzy logic technique. Process parameters such as servo voltage, wire tension, pulse-on-time and pulse-off-time were considered while taking into account several multi-responses such as material removal rate (MRR) and surface roughness (SR). It was found that pulse-on-time of 115 µs, pulse-off-time of 35 µs, servo voltage of 40 V and wire tension of 5 kgf results in a larger value of grey fuzzy reasoning grade (GFRG) which tends to maximize MRR and improve SR. Finally, analysis of variance (ANOVA) is applied to check the influence of each process parameters in the estimation of GFRG.

Sign in / Sign up

Export Citation Format

Share Document