scholarly journals The Flow and Heat Transfer of a Nanofluid Past a Stretching/Shrinking Sheet with a Convective Boundary Condition

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Syahira Mansur ◽  
Anuar Ishak
Keyword(s):  
Nusselt Number ◽  
Brownian Motion ◽  
Local Nusselt Number ◽  
Convective Boundary Condition ◽  
Motion Parameter ◽  
Shrinking Sheet ◽  
Convective Boundary ◽  
Convective Parameter ◽  
Local Sherwood Number ◽  
Brownian Motion Parameter

The boundary layer flow of a nanofluid past a stretching/shrinking sheet with a convective boundary condition is studied. Numerical solutions to the governing equations are obtained using a shooting method. The results are found for the local Nusselt number and the local Sherwood number as well as the temperature and concentration profiles for some values of the convective parameter, stretching/shrinking parameter, Brownian motion parameter, and thermophoresis parameter. The results indicate that the local Nusselt number is consistently higher for higher values of the convective parameter. However, the local Nusselt number decreases with increasing values of the Brownian motion parameter as well as the thermophoresis parameter. In addition, the local Sherwood number increases with increasing Brownian motion parameter and decreases with increasing convective parameter and thermophoresis parameter.

MHD Stagnation-Point Flow of a Nanofluid Past a Stretching Sheet with a Convective Boundary Condition and Radiation Effects

2019 ◽  
Vol 892 ◽  
pp. 168-176 ◽  
Author(s):  
Nor Ain Azeany Mohd Nasir ◽  
Anuar Mohd Ishak ◽  
Ioan Pop
Keyword(s):  
Boundary Condition ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Stagnation Point ◽  
Local Nusselt Number ◽  
Radiation Effects ◽  
Stretching Sheet ◽  
Convective Boundary Condition ◽  
Skin Friction Coefficient ◽  
Convective Boundary

In this paper, the investigation of magnetohydrodynamic (MHD) stagnation point flow of a nanofluid past a stretching sheet with a convective boundary condition and radiation effects is carried out numerically. Similarity transformation is used to reduce the governing partial differential equations into third and second order non-linear ordinary differential equations. These equations are then being solved numerically using a problem solver built in the MATLAB software. The numerical solutions for the skin friction coefficient, local Nusselt number, velocity and temperature profiles for different values of the physical parameters are presented graphically and discussed further. The results indicate that the velocity and the temperature are influenced by the magnetic parameter M, Brownian motion parameter Nb and radiation parameter Nr. The local Nusselt number and the skin friction coefficient are affected significantly in the presence of suction at the boundary.

scholarly journals Sensitivity Analysis on Thermal Conductivity Characteristics of a Water-Based Bionanofluid Flow Past a Wedge Surface

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Sze Qi Chan ◽  
Fazlina Aman ◽  
Syahira Mansur
Keyword(s):  
Brownian Motion ◽  
Differential Equations ◽  
Lewis Number ◽  
Motion Parameter ◽  
Nonlinear Ordinary Differential Equations ◽  
Shooting Technique ◽  
Wedge Surface ◽  
Water Based ◽  
Local Sherwood Number ◽  
Brownian Motion Parameter

Thermobioconvection boundary layer flow in a suspension of water-based bionanofluid holding both nanoparticles and motile microorganisms past a wedge surface was studied. The governing nonlinear partial differential equations on reference of the Buongiorno model were transformed into a set of coupled nonlinear ordinary differential equations. Shooting technique was then used to solve the transformed nonlinear ordinary differential equations numerically. The solutions were found to be contingent on several values of the governing parameters. As highlighted, the velocity profile as well as the skin friction coefficient was affected by the pressure gradient parameter, the function of the wedge angle parameter. On the other hand, the temperature, nanoparticle concentration, and density of motile microorganism’s distributions together with its corresponding local Nusselt number, local Sherwood number, and local density of the motile microorganisms change with the thermophoresis and Brownian motion parameter and so Lewis number, Schmidt number, and bioconvection Péclet number. An experimental scheme together with sensitivity analysis on the basis of Response Surface Methodology (RSM) was applied to examine the dependency of the response parameters of interest to the input parameters’ change. Obviously, local Nusselt number was more sensitive towards the Brownian motion parameter when the Brownian motion parameter was at 0.2 and 0.3. However local Sherwood number was more sensitive towards the Lewis number for all values of Brownian motion parameter. Compatibility found by comparing results between RSM and shooting technique gave confidence for the model’s accuracy. The findings would provide initial guidelines for future device fabrication. Finally, the numerical results obtained were thoroughly inspected and verified with the existing values reported by some researchers.

scholarly journals The Magnetohydrodynamic Boundary Layer Flow of a Nanofluid past a Stretching/Shrinking Sheet with Slip Boundary Conditions

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Syahira Mansur ◽  
Anuar Ishak
Keyword(s):  
Nusselt Number ◽  
Local Nusselt Number ◽  
Magnetic Parameter ◽  
Velocity Slip ◽  
Skin Friction Coefficient ◽  
Shrinking Sheet ◽  
Slip Parameter ◽  
Slip Boundary ◽  
Layer Flow ◽  
Local Sherwood Number

The magnetohydrodynamic (MHD) boundary layer flow of a nanofluid past a stretching/shrinking sheet with velocity, thermal, and solutal slip boundary conditions is studied. Numerical solutions to the governing equations were obtained using a shooting method. The skin friction coefficient and the local Sherwood number increase as the stretching/shrinking parameter increases. However, the local Nusselt number decreases with increasing the stretching/shrinking parameter. The range of the stretching/shrinking parameter for which the solution exists increases as the velocity slip parameter and the magnetic parameter increase. For the shrinking sheet, the skin friction coefficient increases as the velocity slip parameter and the magnetic parameter increase. For the stretching sheet, it decreases when the velocity slip parameter and the magnetic parameter increase. The local Nusselt number diminishes as the thermal slip parameter increases while the local Sherwood number decreases with increasing the solutal slip parameter. The local Nusselt number is lower for higher values of Lewis number, Brownian motion parameter, and thermophoresis parameter.

Stagnation-Point Flow Toward a Stretching/Shrinking Sheet in a Nanofluid Containing Both Nanoparticles and Gyrotactic Microorganisms

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
Khairy Zaimi ◽  
Anuar Ishak ◽  
Ioan Pop
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Stagnation Point ◽  
Sherwood Number ◽  
Local Nusselt Number ◽  
Local Density ◽  
Skin Friction Coefficient ◽  
Shrinking Sheet ◽  
Gyrotactic Microorganisms ◽  
Local Sherwood Number

The stagnation-point flow and heat transfer toward a stretching/shrinking sheet in a nanofluid containing gyrotactic microorganisms with suction are investigated. Using a similarity transformation, the nonlinear system of partial differential equations is converted into nonlinear ordinary differential equations. These resulting equations are solved numerically using a shooting method. The skin friction coefficient, local Nusselt number, local Sherwood number, and the local density of the motile microorganisms as well as the velocity, temperature, nanoparticle volume fraction and the density of motile microorganisms profiles are analyzed subject to several parameters of interest, namely suction parameter, thermophoresis parameter, Brownian motion parameter, Lewis number, Schmidt number, bioconvection Péclet number, and the stretching/shrinking parameter. It is found that dual solutions exist for a certain range of the stretching/shrinking parameter for both shrinking and stretching cases. The results indicate that the skin friction coefficient, local Nusselt number, local Sherwood number, and the local density of the motile microorganisms increase with suction effect. It is also observed that suction widens the range of the stretching/shrinking parameter for which the solution exists.

scholarly journals MHD stagnation point flow of micro nanofluid towards a shrinking sheet with convective and zero mass flux conditions

2017 ◽  
Vol 65 (2) ◽  
pp. 155-162 ◽  
Author(s):  
A. Rauf ◽  
S. A. Shehzad ◽  
T. Hayat ◽  
M. A. Meraj ◽  
A. Alsaedi
Keyword(s):  
Stagnation Point ◽  
Mass Flux ◽  
Numerical Technique ◽  
Convective Boundary Condition ◽  
Momentum Equation ◽  
Stagnation Point Flow ◽  
Shrinking Sheet ◽  
Convective Boundary ◽  
Electrically Conducting ◽  
Zero Mass

AbstractIn this article the stagnation point flow of electrically conducting micro nanofluid towards a shrinking sheet, considering a chemical reaction of first order is investigated. Involvement of magnetic field occurs in the momentum equation, whereas the energy and concentrations equations incorporated the influence of thermophoresis and Brownian motion. Convective boundary condition on temperature and zero mass flux condition on concentration are implemented. Partial differential equations are converted into the ordinary ones using suitable variables. The numerical technique is utilized to discuss the results for velocity, microrotation, temperature, and concentration fields.

Numerical study of Carreau nanofluid flow past vertical plate with the Cattaneo–Christov heat flux model

2019 ◽  
Vol 29 (2) ◽  
pp. 702-723 ◽  
Author(s):  
Vasu B. ◽  
Atul Kumar Ray
Keyword(s):  
Heat Flux ◽  
Brownian Motion ◽  
Weissenberg Number ◽  
Motion Parameter ◽  
Conduction Model ◽  
Content Type ◽  
Carreau Nanofluid ◽  
Flux Model ◽  
Heat Flux Model ◽  
Brownian Motion Parameter

PurposeTo achieve material-invariant formulation for heat transfer of Carreau nanofluid, the effect of Cattaneo–Christov heat flux is studied on a natural convective flow of Carreau nanofluid past a vertical plate with the periodic variations of surface temperature and the concentration of species. Buongiorno model is considered for nanofluid transport, which includes the relative slip mechanisms, Brownian motion and thermophoresis.Design/methodology/approachThe governing equations are non-dimensionalized using suitable transformations, further reduced to non-similar form using stream function formulation and solved by local non-similarity method with homotopy analysis method. The numerical computations are validated and verified by comparing with earlier published results and are found to be in good agreement.FindingsThe effects of varying the physical parameters such as Prandtl number, Schmidt number, Weissenberg number, thermophoresis parameter, Brownian motion parameter and buoyancy ratio parameter on velocity, temperature and species concentration are discussed and presented through graphs. The results explored that the velocity of shear thinning fluid is raised by increasing the Weissenberg number, while contrary response is seen for the shear thickening fluid. It is also found that heat transfer in Cattaneo–Christov heat conduction model is less than that in Fourier’s heat conduction model. Furthermore, the temperature and thermal boundary layer thickness expand with the increase in thermophoresis and Brownian motion parameter, whereas nanoparticle volume fraction increases with increase in thermophoresis parameter, but reverse trend is observed with increase in Brownian motion parameter.Originality/valueThe present investigation is relatively original as very little research has been reported on Carreau nanofluids under the effect of Cattaneo–Christov heat flux model.

scholarly journals MHD three dimensional flow of Oldroyd-B nanofluid over a bidirectional stretching sheet: DTM-Padé Solution

2019 ◽  
Vol 8 (1) ◽  
pp. 744-754 ◽  
Author(s):  
Sumit Gupta ◽  
Sandeep Gupta
Keyword(s):  
Brownian Motion ◽  
Differential Equations ◽  
Prandtl Number ◽  
Comparative Study ◽  
Stretching Sheet ◽  
Fluid Velocity ◽  
Deborah Number ◽  
Motion Parameter ◽  
Physical Parameters ◽  
Brownian Motion Parameter

Abstract Current article is devoted with the study of MHD 3D flow of Oldroyd B type nanofluid induced by bi-directional stretching sheet. Expertise similarity transformation is confined to reduce the governing partial differential equations into ordinary nonlinear differential equations. These dimensionless equations are then solved by the Differential Transform Method combined with the Padé approximation (DTM-Padé). Dealings of the arising physical parameters namely the Deborah numbers β1 and β2, Prandtl number Pr, Brownian motion parameter Nb and thermophoresis parameter Nt on the fluid velocity, temperature and concentration profile are depicted through graphs. Also a comparative study between DTM and numerical method are presented by graph and other semi-analytical techniques through tables. It is envisage that the velocity profile declines with rising magnetic factor, temperature profile increases with magnetic parameter, Deborah number of first kind and Brownian motion parameter while decreases with Deborah number of second kind and Prandtl number. A comparative study also visualizes comparative study in details.

scholarly journals Entropy Analysis in Double-Diffusive Convection in Nanofluids through Electro-osmotically Induced Peristaltic Microchannel

Entropy ◽  
2019 ◽  
Vol 21 (10) ◽  
pp. 986 ◽  
Author(s):  
Noreen ◽  
Waheed ◽  
Hussanan ◽  
Lu
Keyword(s):  
Brownian Motion ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Motion Parameter ◽  
Bejan Number ◽  
Double Diffusive Convection ◽  
Grashof Number ◽  
Diffusive Convection ◽  
Double Diffusive ◽  
Brownian Motion Parameter

A theoretical study is presented to examine entropy generation in double-diffusive convection in an Electro-osmotic flow (EOF) of nanofluids via a peristaltic microchannel. Buoyancy effects due to change in temperature, solute concentration and nanoparticle volume fraction are also considered. This study was performed under lubrication and Debye-Hückel linearization approximation. The governing equations are solved exactly. The effect of dominant hydrodynamic parameters (thermophoresis, Brownian motion, Soret and Dufour), Grashof numbers (thermal, concentration and nanoparticle) and electro-osmotic parameters on double-diffusive convective flow are discussed. Moreover, trapping, pumping, entropy generation number, Bejan number and heat transfer rate were also examined under the influence of pertinent parameters such as the thermophoresis parameter, the Brownian motion parameter, the Soret parameter, the Dufour parameter, the thermal Grashof number, the solutal Grashof number, the nanoparticle Grashof number, the electro-osmotic parameter and Helmholtz–Smoluchowski velocity. The electro-osmotic parameter powerfully affected the velocity profile. The magnitude of total entropy generation increased as the thermophoresis parameter and Brownian motion parameter increased. Soret and the Dufour parameter had a strong tendency to control the temperature profile and Bejan number. The findings of the present analysis can be used in clinical purposes such as cell therapy, drug delivery systems, pharmaco-dynamic pumps and particles filtration.

Sign in / Sign up

Export Citation Format

Share Document