scholarly journals Investigation of the Mechanical Properties of Hybrid Carbon-Hemp Laminated Composites Used as Thermal Insulation for Different Industrial Applications

2014 ◽  
Vol 6 ◽  
pp. 829426 ◽  
Author(s):  
M. L. Scutaru ◽  
M. Baba
Keyword(s):  
Mechanical Properties ◽  
Hybrid Composite ◽  
Composite Laminate ◽  
Industrial Applications ◽  
Impact Testing ◽  
Impact Behavior ◽  
Low Velocity ◽  
Hemp Fabric ◽  
The Impact

Carbon-hemp composite laminate provides good thermal properties. For this reason this type of material is presently being used for various applications like insulator for airplanes, spaceships, nuclear reactors, and so forth. Unfortunately their mechanical properties are less studied. These characteristics are very important since they should be guaranteed also for important mechanical stress in addition to the thermal one. The present paper presents a study regarding the impact testing of some hybrid composite laminate panels based on polyester resin reinforced with both carbon and hemp fabric. The effects of different impact speeds on the mechanical behavior of these panels have been analyzed. The paper lays stress on the characterization of this hybrid composite laminate regarding the impact behavior of these panels by dropping a weight with low velocity.

Low-Velocity Impact Response Characterization of a Hybrid Titanium Composite Laminate

Materials ◽  
2005 ◽  
Author(s):  
S. Bernhardt ◽  
M. Ramulu ◽  
A. S. Kobayashi
Keyword(s):  
Composite Laminate ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Heating Process ◽  
Low Velocity ◽  
Velocity Impact ◽  
Modes Of Failure ◽  
Graphite Fibers ◽  
The Impact

The low-velocity impact response of a hybrid titanium composite laminate (HTCL), known as TiGr, was compared to that of graphite/epoxy composite. The TiGr material comprised of two outer plies of titanium foil surrounding a composite core. The composite core was PIXA-M (a high temperature thermoplastic) reinforced by IM-6 graphite fibers and consolidated by an induction heating process. The impact response of TiGr was characterized by two modes of failure which differed by failure or non-failure in tension of the bottom titanium ply. The ductility of titanium caused buckling by yielding whereas the brittle adjacent composite ply lead to fracture. The maximum failure force of the material correlated well with the previously reported static flexural data, and the material outperformed the commonly used graphite/epoxy.

scholarly journals Fabrication of woven honeycomb structures for advanced composites

2018 ◽  
Vol 1 (3-4) ◽  
pp. 114-119 ◽  
Author(s):  
Guldemet Basal Bayraktar ◽  
◽  
Ata Kianoosh ◽  
Derya Bilen ◽  
◽  
...  
Keyword(s):  
Testing Machine ◽  
Honeycomb Structure ◽  
Impact Testing ◽  
Woven Fabric ◽  
Low Velocity Impact ◽  
Impact Behavior ◽  
Low Velocity ◽  
Detection Range ◽  
Force Contact ◽  
The Impact

A honeycomb woven fabric was designed and produced on a sampling loom. After weaving cells in the fabric were opened by polytetrafluoroethylene (PTFE) sticks and an epoxy resin was applied to fabric. For comparison half of the fabric sample was impregnated with resin without opening the cells. Resulting fabric samples were subjected to low-velocity impact test by using drop weight impact testing machine, CEAST Fractovis Plus – 7526.000. To evaluate the impact behavior of the samples the contact force, contact time, deflection, and absorbed energy values were recorded by data acquisition system (DAS). The energy absorbed by honeycomb structure was around 7 Joule. The energy absorbed by flat sample, on the other hand, was too low and out of the detection range of the testing equipment.

Energy-Absorbing Capacity of Polyurethane/SiC/Glass-Epoxy Laminates Under Impact Loading

2017 ◽  
Vol 139 (2) ◽  
Author(s):  
G. Balaganesan ◽  
V. Akshaj Kumar ◽  
V. C. Khan ◽  
S. M. Srinivasan
Keyword(s):  
Energy Absorption ◽  
Impact Loading ◽  
Composite Laminate ◽  
Failure Modes ◽  
Impact Testing ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Fiber Failure ◽  
The Impact ◽  
Layered Target

This paper presents the energy absorption of target materials with combinations of polyurethane (PU) foam, PU sheet, SiC inserts, and SiC plate bonded to glass fiber reinforced composite laminate backing during impact loading. SiC inserts and SiC plates are bonded as front layer to enhance energy absorption and to protect composite laminate. The composite laminates are prepared by hand lay-up process and other layers are bonded by using epoxy. Low-velocity impact is conducted by using drop mass setup, and mild steel spherical nosed impactor is used for impact testing of target in fixed boundary conditions. Energy absorption and damage are compared to the target plates when subjected to impact at different energy levels. The energy absorbed in various failure modes is analyzed for various layers of target. Failure in the case of SiC inserts is local, and the insert under the impact point is damaged. However, in the other cases, the SiC plate is damaged along with fiber failure and delamination on the composite backing laminate. It is observed that the energy absorbed by SiC plate layered target is higher than SiC inserts layered target.

scholarly journals Impact and Post Impact Behavior of Hybrid Composites

2018 ◽  
Vol 11 (4) ◽  
pp. 46-52
Author(s):  
Aidel Kadum Jassim Al-shamary
Keyword(s):  
Impact Energy ◽  
Hybrid Composites ◽  
Energy Levels ◽  
Testing Machine ◽  
Impact Testing ◽  
Low Velocity Impact ◽  
Impact Behavior ◽  
Low Velocity ◽  
Velocity Impact ◽  
The Impact

In this study, the effect of low velocity impact  response of Kevlar/carbon hybrid composite has been investigated. Then the impacted specimens were subjected to compression and buckling tests at room temperature experimentally. The height, width and thickness of the specimens are 150, 100 and 2.1 mm, respectively. Impact tests have been performed under different impact energy levels by using low velocity impact testing machine. Compression and buckling tests were conducted by Shimadzu testing machine. According to obtained results, the damage increases by increasing the impact energy level in the subjected specimens to impact test.  Compression strength value is higher about 3  times than buckling strength value.

Low-Velocity Impact Response Characterization of a Hybrid Titanium Composite Laminate

2006 ◽  
Vol 129 (2) ◽  
pp. 220-226 ◽  
Author(s):  
S. Bernhardt ◽  
M. Ramulu ◽  
A. S. Kobayashi
Keyword(s):  
Composite Laminate ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Heating Process ◽  
Low Velocity ◽  
Velocity Impact ◽  
Modes Of Failure ◽  
Graphite Fibers ◽  
The Impact

The low-velocity impact response of a hybrid titanium composite laminate, known as TiGr, was compared to that of graphite/epoxy composite. The TiGr material comprised of two outer plies of titanium foil surrounding a composite core. The composite core was PIXA-M (a high temperature thermoplastic) reinforced by IM-6 graphite fibers and consolidated by an induction heating process. The impact response of TiGr was characterized by two modes of failure which differed by failure or nonfailure in tension of the bottom titanium ply. The ductility of titanium caused buckling by yielding whereas the brittle adjacent composite ply lead to fracture. The maximum failure force of the material correlated well with the previously reported static flexural data, and the material outperformed the commonly used graphite/epoxy.

Low Velocity Impact Behavior of SiC/PU/GFRP Laminates

2016 ◽  
Vol 725 ◽  
pp. 122-126 ◽  
Author(s):  
Kumar V. Akshaj ◽  
Chandra Khan Vishwas ◽  
G. Balaganesan ◽  
M.S. Sivakumar
Keyword(s):  
Energy Absorption ◽  
Impact Testing ◽  
Low Velocity Impact ◽  
Impact Behavior ◽  
Low Velocity ◽  
Fiber Failure ◽  
Velocity Impact ◽  
Drop Mass ◽  
Set Up ◽  
The Impact

This paper discusses the energy absorption during low velocity impact on target with combinations of PU foam, SiC inserts/plate bonded to GFRP composite backing. SiC inserts and SiC plates are bonded as front layer to enhance energy absorption. Low velocity impact is conducted by using drop mass set-up and mild steel spherical nosed impactor is used for impact testing of target in fixed boundary conditions. Failure in the case of SiC inserts is local as only the insert under the impact is damaged and nearby areas are intact. However, in the other cases, the SiC plate is damaged along with fiber failure and delamination on the composite backing layer. It is observed that the energy absorbed by SiC plate is higher than that absorbed by SiC inserts layered target.

scholarly journals Effects of temperature and impactor nose diameter on the impact behavior of PA6 and PP thermoplastic composites

2018 ◽  
Vol 51 (1) ◽  
pp. 64-74 ◽  
Author(s):  
Akar Dogan ◽  
Yusuf Arman
Keyword(s):  
Load Capacity ◽  
Testing Machine ◽  
Polyamide 6 ◽  
Impact Testing ◽  
Impact Behavior ◽  
Thermoplastic Composites ◽  
Test Machine ◽  
Effects Of Temperature ◽  
Impact Energies ◽  
The Impact

In this study, the effects of temperature and impactor nose diameter on the impact behavior of woven glass-reinforced polyamide 6 (PA6) and polypropylene (PP) thermoplastic composites were investigated experimentally. Impact energies are chosen as 10, 30, 50, 70, 90, 110, 130, and 170 J. The thickness of composite materials is 4 mm. Impact tests were performed using a drop weight impact testing machine, CEAST-Fractovis Plus, and the load capacity of test machine is 22 kN. Hemispherical impactor nose diameter of 12, 7, and 20 mm were used as an impactor. The tests are conducted at room temperature (20°C and 75°C). As a result, the PP composites of the same thickness absorbed more energy than PA6 composites. The amount of absorbed energy of PP and PA6 composites decreased with temperature.

IMPACT RESISTANCE PROPERTIES OF KEVLAR/GLASS FIBER HYBRID COMPOSITE LAMINATES

2015 ◽  
Vol 76 (3) ◽  
Author(s):  
Norazean Shaari ◽  
Aidah Jumahat ◽  
M. Khafiz M. Razif
Keyword(s):  
Glass Fiber ◽  
Hybrid Composite ◽  
Composite Laminates ◽  
Impact Damage ◽  
Impact Resistance ◽  
Impact Behavior ◽  
Slight Reduction ◽  
Depth Of Penetration ◽  
Damage Degree ◽  
The Impact

In this paper, the impact behavior of Kevlar/glass fiber hybrid composite laminates was investigated by performing the drop weight impact test (ASTM D7136). Composite laminates were fabricated using vacuum bagging process with an epoxy matrix reinforced with twill Kevlar woven fiber and plain glass woven fiber. Four different types of composite laminates with different ratios of Kevlar to glass fiber (0:100, 20:80, 50:50 and 100:0) were manufactured. The effect of Kevlar/glass fiber content on the impact damage behavior was studied at 43J nominal impact energy. Results indicated that hybridization of Kevlar fiber to glass fiber improved the load carrying capability, energy absorbed and damage degree of composite laminates with a slight reduction in deflection. These results were further supported through the damage pattern analysis, depth of penetration and X-ray evaluation tests. Based on literature work, studies that have been done to investigate the impact behaviour of woven Kevlar/glass fiber hybrid composite laminates are very limited. Therefore, this research concentrates on the effect of Kevlar on the impact resistance properties of woven glass fibre reinforced polymer composites.

Low Velocity Impact Resistance of CPVC Pipes Exposed to Natural Outdoor Weathering Conditions

2012 ◽  
Vol 445 ◽  
pp. 959-964
Author(s):  
Z. Khan ◽  
Necar Merah ◽  
A. Bazoune ◽  
S. Furquan
Keyword(s):  
Impact Resistance ◽  
Outdoor Exposure ◽  
Impact Testing ◽  
Low Velocity Impact ◽  
Pipe Material ◽  
Low Velocity ◽  
Impact Energies ◽  
The Impact ◽  
Impact Events ◽  
Outdoor Weathering

Low velocity drop weight impact testing of CPVC pipes was conducted on 160 mm long pipe sections obtained from 4-inch (100 mm) diameter schedule 80 pipes. Impact test were carried out for the base (as received) pipes and after their exposure to out door natural weathering conditions in Dhahran, Saudi Arabia. The results of the impact testing on the natural (outdoor exposure) broadly suggest that the natural outdoor exposures produce no change in the impact resistance of CPVC pipe material for the impact events carrying low incident energies of 10 and 20J. At the impact energies of 35 and 50J the natural outdoor exposures appear to cause appreciable degradation in the impact resistance of the CPVC pipe material. This degradation is noted only for the longer exposure periods of 12 and 18 months.

Low Velocity and Compression-After-Impact Response of Pin-Reinforced Sandwich Composites

1999 ◽  
Author(s):  
Uday K. Vaidya ◽  
Mohan V. Kamath ◽  
Mahesh V. Hosur ◽  
Anwarul Haque ◽  
Shaik Jeelani
Keyword(s):  
Impact Testing ◽  
Low Velocity Impact ◽  
Sandwich Composites ◽  
Low Velocity ◽  
Static Compression ◽  
Velocity Impact ◽  
Transverse Stiffness ◽  
Impact Studies ◽  
Compression After Impact ◽  
The Impact

Abstract In the current work, sandwich composite structures with innovative constructions referred to as Z-pins, or truss core pins are investigated, in conjunction with traditional honeycomb and foam core sandwich constructions, such that they exhibit enhanced transverse stiffness, high damage resistance and furthermore, damage tolerance to impact. While the investigations pertaining to low velocity impact have appeared recently in Vaidya et al. 1999, the current paper deals with compression-after-impact studies conducted to evaluate the residual properties of sandwich composites “with” and “without” reinforced foam cores. The resulting sandwich composites have been investigated for their low velocity (< 5 m/sec) impact loading response using instrumented impact testing at energy levels ranging from 5 J to 50 J impact energy. The transverse stiffness of the cores and their composites has also been evaluated through static compression studies. Compression-after-impact studies were then performed on the sandwich composites with traditional and pin-reinforcement cores. Supporting vibration studies have been conducted to assess the changes in stiffness of the samples as a result of the impact damage. The focus of this paper is on the compression-after-impact (CAI) response and vibration studies with accompanying discussion pertaining to the low velocity impact.

Sign in / Sign up

Export Citation Format

Share Document