scholarly journals Primary Investigation on Equivalent Anchoring Method of Jointed Rock Mass Tunnel and Its Engineering Application

2020 ◽  
Vol 2020 ◽  
pp. 1-16
Author(s):  
Min Gao ◽  
Shanpo Jia
Keyword(s):  
Rock Mass ◽  
Three Dimensional ◽  
Engineering Application ◽  
Friction Angle ◽  
Jointed Rock ◽  
Jointed Rock Mass ◽  
Surrounding Rock ◽  
Rock Masses ◽  
Reinforcement Effect ◽  
Rock Bolts

Rock bolts, one of the main support structures of the tunnel, can improve the stress state and mechanical properties of the surrounding rocks. The rock bolts are simulated by bar or beam elements in present numerical calculations for most 2D tunnel models. However, the methods of simulating rock bolt in three-dimensional models are rarely studied. Moreover, there are too many rock bolts in the long-span tunnel, which are hardly applied in the 3D numerical model. Therefore, an equivalent anchoring method for bolted rock masses needs to be further investigated. First, the jointed material model is modified to simulate the anisotropic properties of surrounding rock masses. Then, based on the theoretical analysis of rock bolts in reinforcing mechanical properties of the surrounding rock masses, the equivalent anchoring method of the jointed rock mass tunnel is numerically studied. The equivalent anchoring method is applied to the stability analysis of a diversion tunnel in Western China. From the calculation results, it could be found that the reinforcement effect of rock bolts could be equivalently simulated by increasing the mechanical parameter value of surrounding rocks. For the jointed rock mass tunnel, the cohesion and internal friction angle of the surrounding rocks are improved as 1.7 times and 1.2 times of the initial value, which can simulate the reinforcement effect of rock bolts. Comparing with analytical results, the improved internal friction angle is nearly consistent with analytical result. The reinforcement effect of rock bolts is simulated obviously when the mechanical parameters of surrounding rocks are increased simultaneously. The engineering application shows that the equivalent anchoring method can reasonably simulate the effect of rock bolts, which can provide reference for stability analysis of three-dimensional tunnel simulations.

Precise grading of surrounding rock based on the numerical calculation of the jointed rock mass

2022 ◽  
pp. 1-32
Author(s):  
Dan Huang ◽  
Xiao-Qing Li ◽  
Wen-Chao Song
Keyword(s):  
Rock Mass ◽  
Numerical Calculation ◽  
Calculation Method ◽  
Jointed Rock ◽  
Jointed Rock Mass ◽  
Surrounding Rock ◽  
Geological Survey ◽  
Survey Method ◽  
Synthetic Rock ◽  
Numerical Calculation Method

In this study, grading of surrounding rock was based on rock mass basic quality (BQ) values according to the specifications in China. Numerical approach was to construct synthetic rock mass (SRM) model to represent the jointed rock mass, and obtain the strength of the rock mass. It represented intact rock by the bonded particle model (BPM), and represent joint behaviour by the smooth joint model (SJM) to construct the discrete fracture network (DFN). In the Hongtuzhang Tunnel, the micro properties of granite cores with different weathered degrees were determined by the validation process, and the calculation representative elementary volume (REV) of surrounding rock was 15 m×15 m. Five slightly weathered, three slightly to moderately weathered, and two moderately weathered granite surrounding rock mass models were established based on the probability distribution of joint sets in each borehole, the conversion BQ value was acquired according by the calculated strength of rock mass model. It was discussed the differences of surrounding rock grades between the geological survey method and the numerical calculation method, and then found that the geological survey report is higher than the numerical calculation method predicted. And the numerical calculation is consistent with the actual excavation of rock mass at borehole A1388.

scholarly journals The Method of Determining Excavation Damaged Zone by Acoustic Test and the Application in Engineering Cases

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Qian-Cheng Sun ◽  
Hao-Sen Guo ◽  
Zhi-Hua Xu ◽  
Yue Liu ◽  
Xiao Xu
Keyword(s):  
Rock Mass ◽  
Damage Evolution ◽  
Hard Rock ◽  
Damage Zone ◽  
Jointed Rock ◽  
Jointed Rock Mass ◽  
Surrounding Rock ◽  
Excavation Damaged Zone ◽  
Damaged Zone ◽  
Columnar Jointed Rock Mass

It is very important to accurately determine the depth of excavation damaged zone for underground engineering excavation and surrounding rock stability evaluation, and it can be measured by acoustic test, but there is no quantitative method for analysis of the results, and it relies heavily on the experience of engineers, which leads to the low reliability of the results and also limits the application of the acoustic method. According to substantial field test data and the feedback of surrounding rock support parameters, the boundary method is proposed to determine the depth of excavation damaged zone in surrounding rock based on the relation between the ultrasonic velocity of measured point and the background wave velocity of rock mass. When the method is applied to the columnar jointed rock mass of Baihetan and the deep-buried hard rock of Jinping, the excavation damaged zone was well judged. The results in the Baihetan project show that the proposed method of determining excavation damage zone by the acoustic test can well demonstrate the anisotropy characteristics of the columnar jointed rock mass, and the damage evolution characteristics of jointed rock mass at the same position can also be obtained accurately. Moreover, the method also can accurately reveal the damage evolution process of the deep-buried hard rock under the condition of high ground stress, which proved the applicability of this method in jointed or nonjointed rock masses.

Stochastic Three-Dimensional Joint Geometry Model and the Properties of REV for a Jointed Rock Mass

2014 ◽  
Vol 1079-1080 ◽  
pp. 266-271
Author(s):  
Wen Hui Tan ◽  
Zhong Hua Sun ◽  
Ning Li ◽  
Xiao Hong Jiang
Keyword(s):  
Rock Mass ◽  
Probability Distributions ◽  
Three Dimensional ◽  
Jointed Rock ◽  
Jointed Rock Mass ◽  
Open Pit ◽  
Mechanical Parameters ◽  
Geometry Model ◽  
Joint Geometry ◽  
3D Network

The lithology of rock mass isnon-homogeneity，anisotropy, andexists size effect. The mechanical parameters of rock mass gotten by engineeringapproaches cannot reflect these properties. Therefore, a newmethod of determining the mechanical parameters of jointed rock mass isproposed: gneiss in Shuichang open-pit mine was selected as a case, thefracture system of the rock mass was measured and analyzed by non-contactmeasuring system of 3GSM and probabilisticmethod,the probability distributions of geometry parameters were analyzed and a 3Djoint geometry model was made by using the program of 3D network modeling.Cubes with different sizes were selected to be tested by tri-axial compressionof numerical simulation with 3DEC based on the 3D network model of joints,thus, the REV and its mechanical parameters were determined, which providedcredible parameters for slope stability analysis.

A New Method to Determining the Strength Parameters of Fractured Rock Mass

2014 ◽  
Vol 898 ◽  
pp. 378-382
Author(s):  
Yun Hua Guo ◽  
Wei Shen Zhu
Keyword(s):  
Rock Mass ◽  
Mechanical Response ◽  
Fractured Rock ◽  
Fracture Network ◽  
Jointed Rock ◽  
Jointed Rock Mass ◽  
Constitutive Relationship ◽  
Hydropower Station ◽  
Rock Masses ◽  
Fractured Rock Mass

A Hydropower Station is located in the middle reach of the Dadu River in southwest China. The natural slope angles are generally 40°~65° and the relative elevation drop is more than 600m. Complex different fractures such as faults, dykes and dense fracture zones due to unloading are developed. Many abutment slopes were formed during construction of the abutments. The stability of these steep and high slopes during construction and operation period plays an important role for the safe construction and operation of the hydropower station. According to the statistical distribution of joints and fractures at the construction site, the slope is divided into a number of engineering geological zones. For each zone, a stochastic fracture network and a numerical model which is close to the real state of the fractured rock mass are established by the Monte-Carlo method. The mechanical response of fractured rock masses with different sizes of numerical models is studied using FLAC3D. The REV characteristic scale is identified for rock masses in the slopes with stochastic fracture network. Numerical simulation is performed to obtain the stress-strain curve, the mechanical parameters and the strength of the jointed rock mass in the zone. A constitutive relationship reflecting the mechanical response of the jointed rock mass in the zone is established. The Comparison between the traditional method and the method in this paper has been made at the end.

scholarly journals Anisotropic Constitutive Model of Intermittent Columnar Jointed Rock Masses Based on the Cosserat Theory

Symmetry ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 823 ◽  
Author(s):  
Wenbin Lu ◽  
Zhende Zhu ◽  
Xiangcheng Que ◽  
Cong Zhang ◽  
Yanxin He
Keyword(s):  
Rock Mass ◽  
Constitutive Model ◽  
Jointed Rock ◽  
Jointed Rock Mass ◽  
Rock Masses ◽  
Cosserat Theory ◽  
Tunnel Excavation ◽  
Jointed Rock Masses ◽  
Columnar Jointed Rock Mass ◽  
Anisotropic Constitutive Model

In this work, an anisotropic constitutive model of hexagonal columnar jointed rock masses is established to describe the distribution law of deformation and the failure of columnar joint caverns under anisotropic conditions, and is implemented to study the columnar jointed rock mass at the dam site of the Baihetan Hydropower Station on the Jinsha River. The model is based on the Cosserat theory and considers the mesoscopic bending effect on the macroscopic mean. The influences of joint plane inclination on equivalent anisotropic elastic parameters are discussed via the introduction of an off-axis transformation matrix and the analysis of an example. It is also pointed out that the six-prism columnar jointed rock mass changes from transverse isotropy to anisotropy under the influence of the angle. A numerical calculation program of the Cosserat constitutive model is developed and is applied to the simulation calculation of a Baihetan diversion tunnel to compare and analyze the respective plastic zones and stress distributions after tunnel excavation under both isotropic and anisotropic conditions. The results reveal that, compared with the isotropic model, the proposed Cosserat anisotropic model better reflects the state of stress and asymmetric distribution of the plastic zone after tunnel excavation, and the actual deformation of the surrounding rock of the tunnel is greater than that calculated by the isotropic method. The results aid in a better understanding of the mechanical properties of rock masses.

scholarly journals Numerical Simulation of Stress Arching Effect in Horizontally Layered Jointed Rock Mass

Symmetry ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1138
Author(s):  
Xiao Huang ◽  
Huaining Ruan ◽  
Chong Shi ◽  
Yang Kong
Keyword(s):  
Rock Mass ◽  
Pressure Coefficient ◽  
Jointed Rock ◽  
Jointed Rock Mass ◽  
Surrounding Rock ◽  
Beam Structure ◽  
Underground Engineering ◽  
Joint Spacing ◽  
Arching Effect ◽  
The Stability

Stress arching effect during the excavation of broken surrounding rock in underground engineering has an important influence on the stability of surrounding rock after underground excavation. To determine the stress arching effect in horizontally layered jointed rock mass, the stress arching characteristics of surrounding rock mass after excavation is analyzed in this study by using a series of numerical tests. The formation mechanism of stress arch is revealed through a comparison of the stress characteristics of a voussoir beam structure and theoretical analysis of multi-block mechanical relationship of jointed rock mass. The method for determining the boundaries of a stress arching zone is proposed, and the influence of various factors on a stress arch is further discussed. Results show that after the excavation of horizontally layered jointed rock mass, the stress arch bunch (SAB) is formed in the lower strata above the cavern, and the global stress arch (GSA) is formed in the higher strata, both of which are symmetrical arch stress patterns. The SAB is the mechanical manifestation of the voussoir beam structure formed by several low-level sandstone layers, and the GSA is caused by the uneven displacement between blocks. Compared with the GSA, the SAB is more sensitive to various influencing factors. The extent of stress arching zone decreases with the increase of an internal friction angle of the joint, lateral pressure coefficient, and overburden depth. In addition, the joint spacing of rock strata is conducive to the development of a stress arch. Results can provide technical support for deformation control and the stability analysis of broken surrounding rock in underground engineering.

scholarly journals Model Test Study on the Anisotropic Characteristics of Columnar Jointed Rock Mass

Symmetry ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 1528
Author(s):  
Zhende Zhu ◽  
Xiangcheng Que ◽  
Zihao Niu ◽  
Wenbin Lu
Keyword(s):  
Rock Mass ◽  
Failure Modes ◽  
Engineering Application ◽  
Jointed Rock ◽  
Structural Features ◽  
Jointed Rock Mass ◽  
Hexagonal Prism ◽  
Compression Tests ◽  
Test Study ◽  
Columnar Jointed Rock Mass

Because of its special structure, the anisotropic properties of columnar jointed rock mass (CJRM) are complicated, which brings difficulty to engineering construction. To comprehensively study the anisotropic characteristics of CJRM, uniaxial compression tests were conducted on artificial CJRM specimens. Quadrangular, pentagonal and hexagonal prism CJRM models were introduced, and the dip direction of the columnar joints was considered. Based on the test results and the structural features of the three CJRM models, the deformation and strength characteristics of CJRM specimens were analyzed and compared. The failure modes and mechanisms of artificial specimens with different dip directions were summarized in accordance with the failure processes and final appearances. Subsequently, the anisotropic degrees of the three CJRM models in the horizontal plane were classified, and their anisotropic characteristics were described. Finally, a simple empirical expression was adopted to estimate the strength and deformation of the CJRM, and the derived equations were used in the Baihetan Hydropower Station project. The calculated values are in good agreement with the existing research results, which reflects the engineering application value of the derived empirical equations.

Sign in / Sign up

Export Citation Format

Share Document