scholarly journals Homogeneous Wave Load Effects on the Connections of Main Parts of Side-Anchored Straight Floating Bridge

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Meysam Rajabi ◽  
Hassan Ghassemi ◽  
Hamidreza Ghafari
Keyword(s):  
Hydrodynamic Interaction ◽  
Numerical Study ◽  
Wave Force ◽  
Wave Forces ◽  
Mooring System ◽  
Wave Direction ◽  
Wave Load ◽  
Mooring Lines ◽  
Homogeneous Wave ◽  
Floating Bridge

In this paper, a numerical study is presented to investigate wave force on the connections of main parts of a side-anchored straight floating bridge concept for the Bjørnafjorden fjord crossing. The floating bridge is supported by 18 pontoons, and three groups of mooring lines are employed to restrain the bridge against horizontal loads and increase its transverse stiffness. The created wave forces at the connections of pontoon-column and column-girder of the floating bridge considering the effects of short-crested and long-crested waves, varying wave direction, hydrodynamic interaction between pontoons, and mooring system are analyzed. It is found that short-crested and long-crested waves depending on their direction decrease or increase the wave forces on the joints. Considering that the effect of hydrodynamic interaction between pontoons can increase or reduce the wave forces and moments created in the joints, which means the neglect of the hydrodynamic interaction effects between the pontoons to simplify the modeling of this type of floating bridge, may be unacceptable. Moreover, the results showed that the bridge mooring system does not merely reduce the wave forces and moments at joints along the bridge.

The Concept of the Optimum Alignment of Discharge Pipelines Due to the Minimization of the Wave Forces

1992 ◽  
Vol 25 (9) ◽  
pp. 211-216
Author(s):  
A. Akyarli ◽  
Y. Arisoy
Keyword(s):  
Wave Height ◽  
Wave Force ◽  
Wave Forces ◽  
Wave Direction ◽  
Incoming Wave ◽  
Pipeline Route ◽  
Optimum Alignment ◽  
The Cost ◽  
Resultant Wave

As the wave forces are the function of the wave height, period and the angle between the incoming wave direction and the axis of the discharge pipeline, the resultant wave force is directly related to the alignment of the pipeline. In this paper, a method is explained to determine an optimum pipeline route for which the resultant wave force becomes minimum and hence, the cost of the constructive measures may decrease. Also, the application of this method is submitted through a case study.

scholarly journals Effects of Mooring Compliancy on the Mooring Forces, Power Production, and Dynamics of a Floating Wave Activated Body Energy Converter

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3535 ◽  
Author(s):  
Luca Martinelli ◽  
Barbara Zanuttigh
Keyword(s):  
Power Production ◽  
Mooring System ◽  
Wave Direction ◽  
Energy Converter ◽  
Energy Device ◽  
Mooring Lines ◽  
Point Absorber ◽  
Deep Waters ◽  
Mooring Forces ◽  
Body Energy

The paper aims at investigating the interactions between a floating wave energy device (WEC) and its mooring system under a variety of wave conditions (regular and irregular, perpendicular and oblique, ordinary and extreme). The analyzed WEC is the DEXA, a wave activated body point absorber, of the type that performs better when aligned to the incident wave direction. Two typologies of mooring systems were studied: for limited depths, the spread system, with a disposition of the lines that do not constrain the yaw movements; for large depths, the catenary anchor leg mooring (CALM) system. The spread system was experimentally investigated, including a realistic power take-off system, to capture non-linear behaviors and assess device motions, power production, and forces on mooring lines. The CALM system was numerically simulated, as mooring modelling is more reliable in deep waters and allows testing of a number of different configurations, by changing the number of the mooring lines and the mooring layout. The experiments showed that a reduction of the mooring compliancy increases the power production. The numerical simulations showed that a redundancy on the number of chains allows a better distribution of the loads, with advantages on reliability and costs.

Numerical Study on Hydrodynamic Behavior of Deepwater Spar Platform with Different Mooring Configurations

2011 ◽  
Vol 137 ◽  
pp. 50-58
Author(s):  
Jin Wei Sun ◽  
Xiu Tao Fan ◽  
Xiao Zheng Wan ◽  
Shi Xuan Liu
Keyword(s):  
Static Analysis ◽  
Numerical Study ◽  
Coupled System ◽  
Element Model ◽  
System Structure ◽  
Mooring Line ◽  
Mooring System ◽  
Performance Study ◽  
Spar Platform ◽  
Mooring Lines

The motion performance of Spar platform and dynamic characteristics for the mooring lines under different mooring configurations have been studied both in static analysis and coupled dynamic analysis. First, 3D hydrodynamic finite element model is built and the effects of the mooring system are taken into account by giving the specified pre-tension, angle and stiffness of the mooring lines on the fairleads. And hydrodynamic analysis of Spar platform is performed by the way of utilizing potential flow theory in frequency domain in order to calculate the hydrodynamic coefficients. Then, static analysis is applied to obtain restoring stiffness curves for the mooring system, structure displacements and mooring line tensions etc.. At last, coupled time domain analysis of the motion response of Spar is conducted for the coupled system and the dynamic tensions of mooring lines are calculated. The research results can be served as a reference for the selection and the performance study for mooring systems during preliminary design.

Hydrodynamic Analysis of Oil Storage Vessels for National Strategic Petroleum Reserve

2011 ◽  
Vol 291-294 ◽  
pp. 2541-2551
Author(s):  
Gang Jun Zhai ◽  
Yong Cheng ◽  
Wen Hua Wang ◽  
Yi Huang
Keyword(s):  
Incident Wave ◽  
Vertical Direction ◽  
Time History ◽  
Wave Force ◽  
Mooring System ◽  
Wave Direction ◽  
Storage Vessel ◽  
Oil Storage ◽  
Motion Responses ◽  
Incident Wave Direction

This paper expatiates hydrodynamic time-domain analysis on strategic oil storage vessels in free floating condition or with dolphin-fender mooring system by means of AQWA numerical software. The results indicate that motion responses of the oil storage vessel with dolphin-fender mooring have improved significantly. The time-history of wave diffraction forces in incident wave direction are basically consistent between the free floating and moored condition. However, in vertical direction of incident wave, the diffraction wave force of the oil storage vessel in free floating condition is obviously different from that with mooring system, which is the result of the coupling interaction between dolphin and vessels. Mooring forces include fender reaction and cable tension, as for which dominate, it depend on evocable motion responses about incident wave direction.

Wind Induced Nonlinear Response of Coupled Spar Platform

2014 ◽  
Author(s):  
Mohammed Jameel ◽  
Suhail Ahmad ◽  
A. B. M. Saiful Islam ◽  
Mohd Zamin Jumaat
Keyword(s):  
Deep Water ◽  
Oil And Gas ◽  
Wave Force ◽  
Wind Loading ◽  
Coupled Analysis ◽  
Mooring Line ◽  
Wave Direction ◽  
Spar Platform ◽  
Mooring Lines ◽  
Spar Platforms

The oil and gas exploration has moved from shallow water to much deeper water far off the continental shelf. Spar platforms under deep water conditions are found to be the most economical and efficient type of offshore platform. Several Spar platforms installed in the Gulf of Mexico and North Sea proves its suitability for deep water exploration. Accurate prediction of motions of a Spar hull is very important for the integrity and associated costs of the riser/mooring line. The most common approach for solving the dynamics of Spar platform is to employ a decoupled quasi-static method, which ignores all or part of the interaction effects between the platform, mooring lines and risers. Coupled analysis, which includes the mooring lines, risers and platform in a single model, is the only way to capture the damping from mooring lines and risers in a consistent manner. The present coupling is capable in matching the forces, displacement, velocities and acceleration for mooring line with Spar hull at the fairlead position and riser with Spar hull at the riser keel connection. It can handle possible significant nonlinearities. The output from such analyses will be platform motions as well as a detailed mooring line and riser responses. In actual field problems hydrodynamic and aerodynamic loads act simultaneously on Spar platform, mooring lines and risers. In finite element model, the entire structure acts as a continuum. This model can handle all nonlinearities, loading and boundary conditions. The selected configuration of Spar platform is analysed under wave force together with wind loading and its structural response behaviour in steady state is studied. An automatic Newmark-β time incremental approach in ABAQUS/AQUA environment has been implemented to conduct the analysis in time domain. The wind force acting on the exposed part of the platform encompasses mean and fluctuating wind components. The frontal region includes the topside assembly and the spar hull portion above the sea level. High degree of nonlinearities makes the solutions convergence sensitive and it requires large number of iterations, at each time station. Spar responses in surge, heave and pitch along with top tension in moorings are computed. The coupled Spar experiences significant lateral shift along wave direction due to wind loading. Increase in standard deviation shows the participation of wind loading giving higher fluctuations. The CML tension increases for wind loading but the extent of the tension fluctuations under wind loading is not much due to high pretension of mooring line.

Experimental and Numerical Study on Large Truncation of Deepwater Mooring Line

2009 ◽  
Author(s):  
Yihua Su ◽  
Jianmin Yang ◽  
Longfei Xiao ◽  
Gang Chen
Keyword(s):  
Dynamic Response ◽  
Water Depth ◽  
Numerical Study ◽  
Unit Length ◽  
Low Frequency ◽  
Model Tests ◽  
Mooring Line ◽  
Mooring System ◽  
Mooring Lines ◽  
Wave Basin

Modeling the deepwater mooring system in present available basin using standard Froude scaling at an acceptable scale presents new challenges. A prospective method is to truncate the full-depth mooring lines and find an equivalent truncated mooring system that can reproduce both static and dynamic response of the full-depth mooring system, but large truncation arise if the water depth where the deepwater platform located is very deep or the available water depth of the basin is shallow. A Cell-Truss Spar operated in 1500m water depth is calibrated in a wave basin with 4m water depth. Large truncation arises even though a small model scale 1:100 is chosen. A series of truncated mooring lines are designed and investigated through numerical simulations, single line model tests and coupled wave basin model tests. It is found that dynamic response of the truncated mooring line can be enlarged by using larger diameter and mass per unit length in air. Although the truncated mooring line with clump presents a “taut” shape, its dynamic characteristics is dominated by the geometry stiffness and it underestimates dynamic response of the full-depth mooring line, even induces high-frequency dynamic response. There are still two obstacles in realizing dynamic similarity for the largely truncated mooring system: lower mean value of the top tension of upstream mooring lines, and smaller low-frequency mooring-induced damping.

scholarly journals Experiment on Pressure Characteristics of Submerged Floating Tunnel with Different Section Types Under Wave Condition

2018 ◽  
Vol 25 (s3) ◽  
pp. 54-60 ◽  
Author(s):  
Qinxi Li ◽  
Shuping Jiang ◽  
Xiang Chen
Keyword(s):  
Wave Height ◽  
Wave Force ◽  
Physical Model Test ◽  
Wave Forces ◽  
Wave Load ◽  
Wave Condition ◽  
Circular Section ◽  
Elliptical Section ◽  
Horizontal Wave ◽  
Submerged Floating Tunnel

Abstract Submerged floating tunnel (SFT for short) is a special underwater traffic structure, and wave load is one of the main environmental loads of SFT structure. In this paper, the 1:60 physical model test of three kinds of SFT in a two-dimensional wave flume is tested. The effects of random irregular waves on the SFT structure under different wave heights and periods are discussed. The study shows that: (1) Compared with circular and polygonal sections, there are multiple local peaks in the elliptical section during the period. with the increase of wave height, the number of local peaks also increases. It suggests that the rotational moment plays an important role in the elliptical section which has a relatively small depth-width ratio. (2) The position of the maximum and minimum pressure in the three kinds of SFT sections is consistent. Their vertical wave forces are all larger than their horizontal wave forces. The increase of vertical wave force relative to horizontal wave force in polygon section is larger than that in elliptical section, and the difference in the circular section is the smallest. (3) Under the same traffic condition, the wave force of the elliptical and polygon section is smaller, but they are more sensitive to the change of wave height, and the increase is obvious. The distribution of wave force in the circular section is more uniform.

Coupled Mooring Analysis and Large Scale Model Tests on a Deepwater Calm Buoy in Mild Wave Conditions

2002 ◽  
Author(s):  
T. H. J. Bunnik ◽  
G. de Boer ◽  
J. L. Cozijn ◽  
J. van der Cammen ◽  
E. van Haaften ◽  
...  
Keyword(s):  
Model Tests ◽  
Irregular Waves ◽  
Scale Model ◽  
Mooring Line ◽  
Wave Forces ◽  
Mooring System ◽  
Mooring Lines ◽  
Pitch Moment ◽  
Numerical Tool ◽  
Decay Tests

This paper describes a series of model tests aimed at gaining insight in the tension variations in the export risers and mooring lines of a CALM buoy. The test result were therefore not only analysed carefully, but were also used as input and to validate a numerical tool that computes the coupled motions of the buoy and its mooring system. The tests were carried out at a model scale of 1 to 20. Captive tests in regular and irregular waves were carried out to investigate non-linearities in the wave forces on the buoy for example from the presence of the skirt. Decay tests were carried out to determine the damping of the buoy’s motions and to obtain the natural periods. Finally, tests in irregular waves were carried out. The dynamics of the mooring system and the resulting damping have a significant effect on the buoy’s motions. A numerical tool has been developed that combines the wave-frequency buoy motions with the dynamical behaviour of the mooring system. The motions of the buoy are computed with a linearised equation of motion. The non-linear motions of the mooring system are computed simultaneously and interact with the buoy’s motions. In this paper, a comparison is shown between the measurements and the simulations. Firstly, the wave forces obtained with a linear diffraction computation with a simplified skirt are compared with the measured wave forces. Secondly, the numerical modelling of the mooring system is checked by comparing line tensions when the buoy moves with the motion as measured in an irregular wave test. Thirdly, the decay tests are simulated to investigate the correctness of the applied viscous damping values. Finally, simulations of a test in irregular waves are shown to validate the entire integrated concept. The results show that: 1. The wave-exciting surge and heave forces can be predicted well with linear diffraction theory. However, differences between the measured and computed pitch moment are found, caused by a simplified modelling of the skirt and the shortcomings of the diffraction model. 2. To predict the tension variations in the mooring lines and risers (and estimate fatigue) it is essential that mooring line dynamics are taken into account. 3. The heave motions of the buoy are predicted well. 4. The surge motions of the buoy are predicted reasonably well. 5. The pitch motions are wrongly predicted.

Numerical Study of Wave Diffraction with Four Cylinders

2014 ◽  
Vol 638-640 ◽  
pp. 1758-1762
Author(s):  
Bao Lei Geng ◽  
Ci Heng Zhang
Keyword(s):  
Mathematical Model ◽  
Incident Wave ◽  
Numerical Study ◽  
Wave Force ◽  
Wave Direction ◽  
Linear Waves ◽  
The Given ◽  
Four Cylinders ◽  
Incident Wave Direction ◽  
Origin Point

By taking the 3D Laplace equation as the basic governing equation, a mathematical model with respect to the interaction between linear waves and arbitrary 3D structures was founded. With an example of wave action with four cylinders, numerical results show that when incident wave direction is 22.5°, wave force Fx on 1# cylinder and 2# cylinder is the biggest and when incident wave direction is 0°, wave force Fx on 3# cylinder and 4# cylinder is the biggest; wave force Fy and the wave height on origin point increases with incident wave direction increasing for the given layout and incident wave conditions.

scholarly journals Mooring Drag Effects in Interaction Problems of Waves and Moored Underwater Floating Structures

2020 ◽  
Vol 8 (3) ◽  
pp. 146
Author(s):  
Cheng-Tsung Chen ◽  
Jaw-Fang Lee ◽  
Chun-Han Lo
Keyword(s):  
Water Waves ◽  
Degrees Of Freedom ◽  
Wave Force ◽  
Wave Forces ◽  
Linear Potential ◽  
Floating Structure ◽  
Mooring Lines ◽  
Wave Fields ◽  
Present Solution ◽  
Scattering And Radiation

In contrast to either considering structures with full degrees of freedom but with wave force on mooring lines neglected or with wave scattering and radiation neglected, in this paper, a new analytic solution is presented for wave interaction with moored structures of full degrees of freedom and with wave forces acting on mooring lines considered. The linear potential wave theory is applied to solve the wave problem. The wave fields are expressed as superposition of scattering and radiation waves. Wave forces acting on the mooring lines are calculated using the Morison equation with relative motions. A coupling formulation among water waves, underwater floating structure, and mooring lines are presented. The principle of energy conservation, as well as numerical results, are used to verify the present solution. With complete considerations of interactions among waves and moored structures, the characteristics of motions of the structure, the wave fields, and the wave forces acting on the mooring lines are investigated.

Sign in / Sign up

Export Citation Format

Share Document