scholarly journals Optimization of Surface Roughness in Drilling Medium-Density Fiberboard with a Parallel Robot

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Elmas Aşkar Ayyıldız ◽  
Mustafa Ayyıldız ◽  
Fuat Kara
Keyword(s):  
Surface Roughness ◽  
Medium Density Fiberboard ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Parallel Robot ◽  
Medium Density ◽  
Taguchi Technique ◽  
Quadratic Regression ◽  
Drilling Parameters ◽  
Optimal Surface

This study focuses on the examination of the effect of cutting parameters on surface roughness when drilling medium-density fiberboard (MDF) with a parallel robot. Taguchi technique was applied to find the optimum drilling parameters and, later, the drilling processing. Experimental layout was established using the Taguchi L18 orthogonal array, and experimental data were examined via a statistical analysis of variance (ANOVA). Experimental results were performed by multiple regression analysis (linear and quadratic). Correlation coefficient (R2) was found 99.46% for surface roughness with the quadratic regression model. By the Taguchi analysis, the optimum values for the surface roughness were found to be a point angle of 118°, a cutting speed of 47.1 m/min, and a feed rate of 0.01 mm/rev. The optimization outcomes presented that the Taguchi technique had been successfully performed to decide the optimal surface roughness of the MDF in the drilling.

Modeling for prediction of surface roughness in milling medium density fiberboard with a parallel robot

Sensor Review ◽  
2019 ◽  
Vol 39 (5) ◽  
pp. 716-723 ◽  
Author(s):  
Mustafa Ayyildiz
Keyword(s):  
Surface Roughness ◽  
Learning Algorithm ◽  
Medium Density Fiberboard ◽  
Back Propagation ◽  
Parallel Robot ◽  
Medium Density ◽  
Mean Square ◽  
Ann Model ◽  
Content Type ◽  
Milling Medium

Purpose This paper aims to discuss the utilization of artificial neural networks (ANNs) and multiple regression method for estimating surface roughness in milling medium density fiberboard (MDF) material with a parallel robot. Design/methodology/approach In ANN modeling, performance parameters such as root mean square error, mean error percentage, mean square error and correlation coefficients (R2) for the experimental data were determined based on conjugate gradient back propagation, Levenberg–Marquardt (LM), resilient back propagation, scaled conjugate gradient and quasi-Newton back propagation feed forward back propagation training algorithm with logistic transfer function. Findings In the ANN architecture established for the surface roughness (Ra), three neurons [cutting speed (V), feed rate (f) and depth of cut (a)] were contained in the input layer, five neurons were included in its hidden layer and one neuron was contained in the output layer (3-5-1).Trials showed that LM learning algorithm was the best learning algorithm for the surface roughness. The ANN model obtained with the LM learning algorithm yielded estimation training values R2 (97.5 per cent) and testing values R2 (99 per cent). The R2 for multiple regressions was obtained as 96.1 per cent. Originality/value The result of the surface roughness estimation model showed that the equation obtained from the multiple regressions with quadratic model had an acceptable estimation capacity. The ANN model showed a more dependable estimation when compared with the multiple regression models. Hereby, these models can be used to effectively control the milling process to reach a satisfactory surface quality.

Prediction and optimization of surface roughness in milling of medium density fiberboard (MDF) based on Taguchi orthogonal array experiments

Holzforschung ◽  
2008 ◽  
Vol 62 (2) ◽  
pp. 209-214 ◽  
Author(s):  
Vinayak N. Gaitonde ◽  
S. Ramesh Karnik ◽  
João Paulo Davim
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Orthogonal Array ◽  
Medium Density Fiberboard ◽  
Cutting Speed ◽  
Medium Density ◽  
Taguchi Optimization ◽  
Taguchi Orthogonal Array ◽  
Roughness Model ◽  
Order Surface

Abstract The main objective of this paper was to develop a mathematical model to predict the surface roughness and to determine the optimal cutting conditions during milling of medium density fiberboard. The milling experiments were carried out as per Taguchi orthogonal array with feed rate and cutting speed as the controlling parameters. A second-order surface roughness model has been developed using the methodology of response surface analysis. The paper presents the details of analysis of variance to validate the developed model. The Taguchi optimization results show that the surface roughness can be optimized with lower feed rate and higher cutting speed values.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

Effect of species and grinding disc distance on the surface roughness parameters of medium density fiberboard

2016 ◽  
Vol 75 (3) ◽  
pp. 335-346 ◽  
Author(s):  
Lidia Gurau ◽  
Nadir Ayrilmis ◽  
Jan Thore Benthien ◽  
Martin Ohlmeyer ◽  
Manja Kitek Kuzman ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Medium Density Fiberboard ◽  
Medium Density ◽  
Roughness Parameters ◽  
Surface Roughness Parameters

Experimental Investigation on Surface Roughness in Precision Cutting Ti6Al4V Alloy Using Diamond Tools

2014 ◽  
Vol 800-801 ◽  
pp. 576-579
Author(s):  
Lin Hua Hu ◽  
Ming Zhou ◽  
Yu Liang Zhang
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Polycrystalline Diamond ◽  
Cutting Parameters ◽  
Limited Range ◽  
Nose Radius ◽  
Machined Surface ◽  
Machined Surface Roughness ◽  
Titanium Alloy Ti6al4v ◽  
Pcd Tools

In this work, cutting experiments were carried out on titanium alloy Ti6Al4V by using polycrystalline diamond (PCD) tools to investigate the effects of the tool geometries and cutting parameters on machined surface roughness. Experimental results show machined surface roughness decreases with increases in the flank angle, tool nose radius and cutting speed within a limited range respectively, and begins to increase as the factors reaches to certain values respectively. And machined surface roughness decreases with increases in feed rate and cutting depth respectively.

Effect of Cutting Parameters on Surface Roughness in Turning of Bone

2013 ◽  
Vol 845 ◽  
pp. 708-712 ◽  
Author(s):  
P.Y.M. Wibowo Ndaruhadi ◽  
S. Sharif ◽  
M.Y. Noordin ◽  
Denni Kurniawan
Keyword(s):  
Surface Roughness ◽  
Bone Tissue ◽  
Influencing Factor ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Conditions ◽  
Machining Process ◽  
Turning Operation ◽  
Cutting Direction

Surface roughness indicates the damage of the bone tissue due to bone machining process. Aiming at inducing the least damage, this study evaluates the effect of some cutting conditions to the surface roughness of machined bone. In the turning operation performed, the variables are cutting speed (26 and 45 m/min), feed (0.05 and 0.09 mm/rev), tool type (coated and uncoated), and cutting direction (longitudinal and transversal). It was found that feed did not significantly influence surface roughness. Among the influencing factor, the rank is tool type, cutting speed, and cutting direction.

OPTIMISING CUTTING PARAMETERS FOR HOT TURNING ON EN31 MATERIAL

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Prof. Hemant k. Baitule ◽  
Satish Rahangdale ◽  
Vaibhav Kamane ◽  
Saurabh Yende
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Multiple Time ◽  
Turning Process ◽  
Workpiece Material ◽  
Hot Turning

In any type of machining process the surface roughness plays an important role. In these the product is judge on the basis of their (surface roughness) surface finish. In machining process there are four main cutting parameter i.e. cutting speed, feed rate, depth of cut, spindle speed. For obtaining good surface finish, we can use the hot turning process. In hot turning process we heat the workpiece material and perform turning process multiple time and obtain the reading. The taguchi method is design to perform an experiment and L18 experiment were performed. The result is analyzed by using the analysis of variance (ANOVA) method. The result Obtain by this method may be useful for many other researchers.

Evaluation of Process Parameters in Machining of AA6063 Alloy

2018 ◽  
Vol 1148 ◽  
pp. 109-114
Author(s):  
M. Balaji ◽  
C.H. Nagaraju ◽  
V.U.S. Vara Prasad ◽  
R. Kalyani ◽  
B. Avinash
Keyword(s):  
Surface Roughness ◽  
Regression Analysis ◽  
Process Parameters ◽  
Single Channel ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Roughness Parameters ◽  
Surface Roughness Parameters ◽  
Aa6063 Alloy

The main aim of this work is to analyse the significance of cutting parameters on surface roughness and spindle vibrations while machining the AA6063 alloy. The turning experiments were carried out on a CNC lathe with a constant spindle speed of 1000rpm using carbide tool inserts coated with Tic. The cutting speed, feed rate and depth of cut are chosen as process parameters whose values are varied in between 73.51m/min to 94.24m/min, 0.02 to 0.04 mm/rev and 0.25 to 0.45 mm respectively. For each experiment, the surface roughness parameters and the amplitude plots have been noted for analysis. The output data include surface roughness parameters (Ra,Rq,Rz) measured using Talysurf and vibration parameter as vibration amplitude (mm/sec) at the front end of the spindle in transverse direction using single channel spectrum analyzer (FFT).With the collected data Regression analysis is also performed for finding the optimum parameters. The results show that significant variation of surface irregularities and vibration amplitudes were observed with cutting speed and feed. The optimum cutting speed and feed from the regression analysis were 77.0697m/min and 0.0253mm/rev. for the minimum output parameters. No significant effect of depth of cut on output parameters is identified.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

Improvement of Surface Roughness in End Milling of Ti6Al4V by Coupling RSM with Genetic Algorithm

2011 ◽  
Vol 264-265 ◽  
pp. 1154-1159
Author(s):  
Anayet Ullah Patwari ◽  
A.K.M. Nurul Amin ◽  
S. Alam
Keyword(s):  
Genetic Algorithm ◽  
Surface Roughness ◽  
Titanium Alloys ◽  
End Milling ◽  
Fitness Function ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Resistance Surface

Titanium alloys are being widely used in the aerospace, biomedical and automotive industries because of their good strength-to-weight ratio and superior corrosion resistance. Surface roughness is one of the most important requirements in machining of Titanium alloys. This paper describes mathematically the effect of cutting parameters on Surface roughness in end milling of Ti6Al4V. The mathematical model for the surface roughness has been developed in terms of cutting speed, feed rate, and axial depth of cut using design of experiments and the response surface methodology (RSM). Central composite design was employed in developing the surface roughness models in relation to primary cutting parameters. The experimental results indicate that the proposed mathematical models suggested could adequately describe the performance indicators within the limits of the factors that are being investigated. The developed RSM is coupled as a fitness function with genetic algorithm to predict the optimum cutting conditions leading to the least surface roughness value. MATLAB 7.0 toolbox for GA is used to develop GA program. The predicted results are in good agreement with the experimental one and hence the model can be efficiently used to achieve the minimum surface roughness value.

Sign in / Sign up

Export Citation Format

Share Document