Evaluation of Process Parameters in Machining of AA6063 Alloy

2018 ◽  
Vol 1148 ◽  
pp. 109-114
Author(s):  
M. Balaji ◽  
C.H. Nagaraju ◽  
V.U.S. Vara Prasad ◽  
R. Kalyani ◽  
B. Avinash
Keyword(s):  
Surface Roughness ◽  
Regression Analysis ◽  
Process Parameters ◽  
Single Channel ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Roughness Parameters ◽  
Surface Roughness Parameters ◽  
Aa6063 Alloy

The main aim of this work is to analyse the significance of cutting parameters on surface roughness and spindle vibrations while machining the AA6063 alloy. The turning experiments were carried out on a CNC lathe with a constant spindle speed of 1000rpm using carbide tool inserts coated with Tic. The cutting speed, feed rate and depth of cut are chosen as process parameters whose values are varied in between 73.51m/min to 94.24m/min, 0.02 to 0.04 mm/rev and 0.25 to 0.45 mm respectively. For each experiment, the surface roughness parameters and the amplitude plots have been noted for analysis. The output data include surface roughness parameters (Ra,Rq,Rz) measured using Talysurf and vibration parameter as vibration amplitude (mm/sec) at the front end of the spindle in transverse direction using single channel spectrum analyzer (FFT).With the collected data Regression analysis is also performed for finding the optimum parameters. The results show that significant variation of surface irregularities and vibration amplitudes were observed with cutting speed and feed. The optimum cutting speed and feed from the regression analysis were 77.0697m/min and 0.0253mm/rev. for the minimum output parameters. No significant effect of depth of cut on output parameters is identified.

EVALUATION OF SURFACE ROUGHNESS PRODUCED BY NANOCUTTING COPPER STRUCTURE USING A LEAST SQUARE MEAN METHOD

2019 ◽  
Vol 27 (01) ◽  
pp. 1950081 ◽  
Author(s):  
CHUNHUI JI ◽  
SHUANGQIU SUN ◽  
BIN LIN ◽  
TIANYI SUI
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Least Square ◽  
Depth Of Cut ◽  
Real Surface ◽  
Roughness Parameters ◽  
Machined Surface ◽  
Surface Roughness Parameters ◽  
3D Surface ◽  
3D Surface Roughness

This work performed molecular dynamic simulations to study the 2D profile and 3D surface topography in the nanometric cutting process. The least square mean method was used to model the evaluation criteria for the surface roughness at the nanometric scale. The result showed that the cutting speed was the most important factor influencing the spacing between the peaks, the sharpness of the peaks, and the randomness of the profile. The plastic deformation degree of the machined surface at the nanometric scale was significantly influenced by the cutting speed and depth of cut. The 2D and 3D surface roughness parameters exhibited a similar variation tendency, and the parameters Ra and Rq tended to increase gradually with an increase in the cutting speed and a decrease in the depth of cut. Finally, it is concluded that at the nanometric scale, the 3D surface roughness parameters could more accurately reflect the real surface characteristics than the 2D parameters.

scholarly journals Surface Quality Assessment after Milling AZ91D Magnesium Alloy Using PCD Tool

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 617 ◽  
Author(s):  
Ireneusz Zagórski ◽  
Jarosław Korpysa
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Roughness Parameters ◽  
Operational Parameters

Surface roughness is among the key indicators describing the quality of machined surfaces. Although it is an aggregate of several factors, the condition of the surface is largely determined by the type of tool and the operational parameters of machining. This study sought to examine the effect that particular machining parameters have on the quality of the surface. The investigated operation was the high-speed dry milling of a magnesium alloy with a polycrystalline diamond (PCD) cutting tool dedicated for light metal applications. Magnesium alloys have low density, and thus are commonly used in the aerospace or automotive industries. The state of the Mg surfaces was assessed using the 2D surface roughness parameters, measured on the lateral and the end face of the specimens, and the end-face 3D area roughness parameters. The description of the surfaces was complemented with the surface topography maps and the Abbott–Firestone curves of the specimens. Most 2D roughness parameters were to a limited extent affected by the changes in the cutting speed and the axial depth of cut, therefore, the results from the measurements were subjected to statistical analysis. From the data comparison, it emerged that PCD-tipped tools are resilient to changes in the cutting parameters and produce a high-quality surface finish.

Studies Regarding the Influence on the Surface Roughness Material of the Cutting Regime during the Milling Processing

2015 ◽  
Vol 1128 ◽  
pp. 271-281 ◽  
Author(s):  
Mihai Demian ◽  
Luminita Grecu ◽  
Gabriela Demian
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Optimal Parameter ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Error Variance ◽  
Milling Process ◽  
Depth Of Cut ◽  
Low Level ◽  
First Case

The aim of the present paper is to establish the optimal parameter values of the cutting regime of a milling process. The paper presents a study regarding the influence of the cutting parameters on the surface roughness of the material and also on the vibration generated by their combinations, during a processing by milling. The studies are made on samples made from S355 JR steel with a metal milling machine FUS 25, which is used also for the experiments. The samples dimensions are 210x150x16mm. For the experiments there was used a cylindrical - frontal milling tool, with 32mm diameter and 10 tooth. Basic parameters of milling processing of materials we have considered in this paper are: feed rate [mm/min]; cutting speed RPM [rot/min]; depth of cut [mm]. For each of this parameters three levels were envisaged. For a 100% accurate experiment results at least 27 experiments must be done. Using an L9 orthogonal array, the number of experiments is reduced to nine and the accurate of the method is around 99.96%. The optimal process parameters values are obtained using Taguchi method considering three situations. In the first case the goal is to get only a fine roughness for the sample. The second studied case is focused on finding a low level for the vibration generated during the milling process. The aim of the last study is to find a fine roughness and also a low level of vibration for the process. The analysis of variance (ANOVA) is applied, in all cases, in order to estimate the error variance and to rank the process parameters according to their importance.

scholarly journals Modeling and Parameter Optimization for Surface Roughness and Residual Stress in Dry Turning Process

2017 ◽  
Vol 7 (5) ◽  
pp. 2047-2055
Author(s):  
M. H. El-Axir ◽  
M. M. Elkhabeery ◽  
M. M. Okasha
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Feed Rate ◽  
Rotational Speed ◽  
Cutting Speed ◽  
Electrochemical Analysis ◽  
Depth Of Cut ◽  
Roughness Parameters ◽  
Etching Technique ◽  
Surface Roughness Parameters

The influence of some turning variables and tool overhang on surface roughness parameters and residual stress induced due to machining 6061-T6 aluminum alloy is investigated in this paper. Four input parameters (cutting speed, feed rate, depth of cut and tool overhang) are considered. Tests are carried out by precision turning operation on a lathe. Design of experiment techniques, i.e. response surface methodology (RSM) and Taguchi's technique have been used to accomplish the objective of the experimental study. Surface roughness parameters are measured using a portable surface roughness device while residual stresses are measured employing deflection-etching technique using electrochemical analysis. The results obtained reveal that feed and rotational speed play significant role in determining the average surface roughness. Furthermore, the depth of cut and tool overhang are less significant parameters, whereas tool overhang interacts with feed rate. The best result of surface roughness was obtained using low or medium values of overhang with low speed and /or feed rate. Minimum maximum tensile residual stress can be obtained with a combination of tool overhang of 37 mm with very low depth of cut, low rotational speed and feed rate of 0.188 mm/rev.

scholarly journals ESTIMATING THE EFFECT OF MACHINING PARAMETERS ON SURFACE ROUGHNESS DURING MACHINING OF HARDENED EN24 STEEL USING COATED CARBIDE INSERTS

2014 ◽  
pp. 123-128
Author(s):  
Sudhansu Ranjan Das ◽  
Amaresh Kumar ◽  
Debabrata Dhupal ◽  
Kali Charan Rath
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Roughness Parameters ◽  
Surface Roughness Parameters ◽  
Hardened En24 ◽  
Coated Carbide ◽  
The Relationship ◽  
Carbide Inserts

In the present study, an attempt has been made to evaluate the performance of multilayer coated carbide inserts during dry turning of hardened EN24 steel (47 HRC). The effect of machining parameters (depth of cut, feed and cutting speed) on surface roughness parameters (Ra and Rz) were investigated by applying ANOVA. The experiments were planned based on Taguchi’s L27 Orthogonal array design. Results showed that surface roughness parameters (Ra and Rz) are mainly influenced by feed and cutting speed, whereas depth of cut exhibits minimum influence on surface roughness (Rz) and neglegible influence in case of surface roughness (Ra). The experimental data were further anlyzed to predict the optimal range of surface roughness parameters (Ra and Rz). Finally, second order regression models were carried out to find out the relationship between the machining parameters and surface roughness parameters.

Application of Taguchi’s Method for Study of Machining Parameters on Surface Roughness of 7136 Aluminum Alloy in End Milling

2015 ◽  
Vol 809-810 ◽  
pp. 123-128 ◽  
Author(s):  
Alina Bianca Bonţiu Pop
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Process Parameters ◽  
End Milling ◽  
Signal To Noise Ratio ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Future Research ◽  
Depth Of Cut ◽  
Machining Parameters

Starting with the necessity to identify the optimum values of the cutting parameters which are affecting the surface quality, it is appropriate to use the design of experiment techniques to conduct the experiments. Previous researches [1] focused on the investigation of the effects of machining parameters on surface roughness. In this paper, the experiments were conducted based on the established Taguchi’s technique, L8 orthogonal array using Minitab-17 statistical software. Three machining parameters are chosen as process parameters: Cutting Speed, Feed per tooth and Depth of cut. The orthogonal matrix includes these three factors set for analysis, each with 2 levels associated. The level of influence that the process parameters exert on the surface roughness is analyzed by Taguchi method data analysis. In this case the signal to noise ratio was tacked into account. Also, the recommended configuration regarding the optimum values of these parameters was determined as well as the interactions between them, in order to obtain better surface roughness for 7136 aluminum alloy machining. The final results will be used as data for future research.

scholarly journals Investigation on the Surface Quality Obtained during Trochoidal Milling of 6082 Aluminum Alloy

Machines ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 75
Author(s):  
Nikolaos E. Karkalos ◽  
Panagiotis Karmiris-Obratański ◽  
Szymon Kurpiel ◽  
Krzysztof Zagórski ◽  
Angelos P. Markopoulos
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Process Parameters ◽  
Manufacturing Industry ◽  
High Surface ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Surface Quality ◽  
Trochoidal Milling

Surface quality has always been an important goal in the manufacturing industry, as it is not only related to the achievement of appropriate geometrical tolerances but also plays an important role in the tribological behavior of the surface as well as its resistance to fatigue and corrosion. Usually, in order to achieve sufficiently high surface quality, process parameters, such as cutting speed and feed, are regulated or special types of cutting tools are used. In the present work, an alternative strategy for slot milling is adopted, namely, trochoidal milling, which employs a more complex trajectory for the cutting tool. Two series of experiments were initially conducted with traditional and trochoidal milling under various feed and cutting speed values in order to evaluate the capabilities of trochoidal milling. The findings showed a clear difference between the two milling strategies, and it was shown that the trochoidal milling strategy is able to provide superior surface quality when the appropriate process parameters are also chosen. Finally, the effect of the depth of cut, coolant and trochoidal stepover on surface roughness during trochoidal milling was also investigated, and it was found that lower depths of cut, the use of coolant and low values of trochoidal stepover can lead to a considerable decrease in surface roughness.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

OPTIMISING CUTTING PARAMETERS FOR HOT TURNING ON EN31 MATERIAL

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Prof. Hemant k. Baitule ◽  
Satish Rahangdale ◽  
Vaibhav Kamane ◽  
Saurabh Yende
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Multiple Time ◽  
Turning Process ◽  
Workpiece Material ◽  
Hot Turning

In any type of machining process the surface roughness plays an important role. In these the product is judge on the basis of their (surface roughness) surface finish. In machining process there are four main cutting parameter i.e. cutting speed, feed rate, depth of cut, spindle speed. For obtaining good surface finish, we can use the hot turning process. In hot turning process we heat the workpiece material and perform turning process multiple time and obtain the reading. The taguchi method is design to perform an experiment and L18 experiment were performed. The result is analyzed by using the analysis of variance (ANOVA) method. The result Obtain by this method may be useful for many other researchers.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

Sign in / Sign up

Export Citation Format

Share Document