scholarly journals Parameters Optimization of Dissimilar Friction Stir Welding for AA7079 and AA8050 through RSM

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
M. Kavitha ◽  
V. M. Manickavasagam ◽  
T. Sathish ◽  
Bhiksha Gugulothu ◽  
A. Sathish Kumar ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Engineering Application ◽  
Parameters Optimization ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Dissimilar Friction Stir Welding ◽  
Constituent Elements ◽  
Tool Pin

Aluminium alloy is widely used in engineering application, and it can be classified based on the constituent elements or alloying elements. Aluminium alloy is preferred for the nature of its tensile strength, ductility, and corrosion resistance in this research to make a dissimilar friction stir welding joint of aluminium alloys 7079 and 8050 materials. The tensile strength of the weld joint is estimated by the influence of the response surface methodology approach. The welding is carried out by preferred process parameters with a tool speed of 1000–2500 rpm, tool pin diameter of 2–6 mm, welding speed of 50–300 mm/min, and tool shoulder diameter of 10–20 mm. The ANOVA analysis and the prediction of tensile strength were conducted efficiently. From the RSM analysis, the tool pin diameter mostly modified the output of the result.

Influences of Tool pin Profile and Tool Shoulder Curvature on the Formation of Friction Stir Welding Zone in AA6061 Aluminium Alloy

2012 ◽  
Vol 445 ◽  
pp. 789-794 ◽  
Author(s):  
Vahid Moosabeiki ◽  
Ghasem Azimi ◽  
Mostafa Ghayoor
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Zone Formation ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Tool Shoulder ◽  
Aa6061 Aluminium Alloy ◽  
Tool Pin

Friction stir welding (FSW) process is an emerging solid state joining process in which the material that is being welded does not melt and recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters such as tool rotational speed, welding speed, axial force, etc., and tool pin profile play a major role in deciding the weld quality. Friction stir tool plays a major role in friction stir welding process. In this investigation, it is tried to evaluate the effect of tool pin thread and tool shoulder curvature on FSW zone formation in AA6061 aluminium alloy. In this regard, six different tool pin geometries (threadless triangular pin with/without conical shoulder, threaded triangular pin with conical shoulder, threadless square pin with/without conical shoulder, threaded square pin with conical shoulder) are used to fabricate the joints. The formation of FSP zones are analyzed macroscopically. Tensile properties of the joints are evaluated and correlated with the FSP zone formation. Consequently, it is obtained that welding creates a higher quality compared to other tool pin profiles using the square tool with curved shoulder and having threaded pin.

Optimization of friction stir welding parameters of dissimilar aluminium alloys 6061 and 5083 by using response surface methodology

2021 ◽  
pp. 095440622110058
Author(s):  
Sanjeev Verma ◽  
Vinod Kumar
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Tilt Angle ◽  
Feed Rate ◽  
Aluminium Alloys ◽  
Welded Joint ◽  
Welding Parameters ◽  
Friction Stir ◽  
Industrial Sectors ◽  
Tool Pin

Aluminium and its alloys are lightweight, corrosion-resistant, affordable and high-strength material and find wide applications in shipbuilding, automotive, constructions, aerospace and other industrial sectors. In applications like aerospace, marine and automotive industries, there is a need to join components made of different aluminium alloys, viz. AA6061 and AA5083. In this study friction stir welding (FSW) is used to join dissimilar plates made of AA6061-T6 and AA5083-O. The effect of varying tool pin profile, tool rotation speed, tool feed rate and tilt angle of the tool has been investigated on the tensile strength and percentage elongation of the welded joints. Box-Behkan design, with four input parameters and three levels of each parameter has been employed to decide the set of experimental runs. The regression models have been developed to investigate the influence of welding variables on the tensile strength and elongation of the welded joint. It is revealed that with the increase in welding parameters like tool rpm, tool feed rate and tilt angle of the tool, both the mechanical properties increase, reach a maximum level, followed by a decrease with further increase in the value of parameters. Amongst different types of tool pin profiles used, the FSW tool having straight cylindrical (SC) pin profile is found to yield the maximum strength and elongation of the welded joint for different combinations of welding parameters. Multiple response optimization indicates that the maximum UTS (135.83 MPa) and TE (4.35%) are obtained for the welded joint fabricated using FSW tool having SC pin profile, tilted at 1.11° and operating at tool speed and feed rate of 1568 rpm and 39.53 mm/min., respectively.

Effect of Friction Stir Welding Parameters on Thermal and Tensile Behavior of Aluminum Weldments Using Double Shoulder Tools

2012 ◽  
Vol 622-623 ◽  
pp. 323-329
Author(s):  
Ebtisam F. Abdel-Gwad ◽  
A. Shahenda ◽  
S. Soher
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Tensile Behavior ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Friction Stir ◽  
Aluminum Base ◽  
Tool Pin ◽  
Strength And Ductility

Friction stir welding (FSW) process is a solid state welding process in which the material being welded does not melt or recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters and tool pin profile play major roles in deciding the weld quality. In this investigation, an attempt has been made to understand effects of process parameters include rotation speeds, welding speeds, and pin diameters on al.uminum weldment using double shoulder tools. Thermal and tensile behavior responses were examined. In this direction temperatures distribution across the friction stir aluminum weldment were measured, besides tensile strength and ductility were recorded and evaluated compared with both single shoulder and aluminum base metal.

Effects of Tool Pin Profile and Tool Shoulder Diameter on the Tensile Behaviour of Friction Stir Welded Joints of Aluminium Alloys

2014 ◽  
Vol 984-985 ◽  
pp. 586-591 ◽  
Author(s):  
R. Ashok Kumar ◽  
M.R. Thansekhar
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Tensile Properties ◽  
Welded Joints ◽  
Tensile Behaviour ◽  
Light Weight ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Shoulder Diameter ◽  
Weight Structures

— For fabricating light weight structures, it requires high strength-to weight ratio. AA6061 aluminium alloy is widely used in the fabrication of light weight structures. A356 aluminium alloy has wide spread application in aerospace industries. Friction stir welding is solid state joining process which is conducting for joining similar and dissimilar materials. The friction stir welding parameters play an important role for deciding the strength of welded joints. In this investigation, A356 and AA6061 alloys were friction stir welded by varying triangular, square, hexagonal pin profiles of tool keeping the remaining parameters same and AA6061 alloys were friction stir welded by varying tool shoulder diameter as 12mm,15mm,18mm without changing other parameters. Tensile properties of each joint have been analyzed microscopically. From the experimental results, it is observed that hexagonal pin profiled tool and 15mm shoulder diameter tool provides higher tensile properties when compared to other tools.

Optimization of Welding Process Parameters in Novel Friction Stir Welding of Polyamide 66 Joints

2019 ◽  
Vol 969 ◽  
pp. 828-833 ◽  
Author(s):  
R. Nandhini ◽  
R. Dinesh Kumar ◽  
S. Muthukumaran ◽  
S. Kumaran
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Welding Process ◽  
Polyamide 66 ◽  
Friction Stir ◽  
Response Characteristics ◽  
Tool Shoulder ◽  
Stereo Microscope ◽  
Friction Plate

The friction stir welding of polyamide 66 with a specially modified tool is studied. A variation of the conventional friction stir welding is investigated by incorporating a friction plate for the purpose of heating the polymer in the course of welding process through the tool shoulder. This in turn, improves the efficiency of the weld. The association of the welding process parameters and the weld performance has been investigated by the grey relational analysis with multi response characteristics like weld tensile strength, percent elongation and hardness. Macrostructure of the weld joint cross section has been explored by Stereo microscope. The maximum weld tensile strength of 63 MPa and a Shore hardness of 60 D at the weld nugget are obtained. The hardness profiles of the welded samples have been analyzed in this investigation.

Effect of Tool pin Profile and Axial Force on Tensile Behavior in Friction Stir Welding of Dissimilar Aluminum Alloys

2011 ◽  
Vol 415-417 ◽  
pp. 1140-1146 ◽  
Author(s):  
R. Palanivel ◽  
P. Koshy Mathews ◽  
M. Balakrishnan ◽  
I. Dinaharan ◽  
N. Murugan
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Axial Force ◽  
Aluminium Alloys ◽  
Welding Process ◽  
Fusion Welding ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Dissimilar Aluminum Alloys ◽  
Tool Pin

Aluminium alloys generally has low weldability by traditional fusion welding process. The development of the Friction Stir Welding (FSW) has provided an alternative improved way of producing aluminium joints, in a faster and reliable manner. FSW process has several advantages, in particular the possibility to weld dissimilar aluminium alloys. This study focuses on the behavior of tensile strength of dissimilar joints of AA6351-T6 alloy to AA5083-H111 alloy produced by friction stir welding was analysed. Five different tool pin profile such as Straight Square (SS), Tapered Square (TS), Straight Hexagon (SH), Straight Octagon (SO) and Tapered Octagon (TO) with three different axial force (1tonne, 1.5tonne, 2 tonne) have been used to weld the joints. The effect of pin profiles and axial force on tensile properties and material flow behaviour of the joint was analyzed and it was found that the straight square pin profile with 1.5 tonne produced better tensile strength then other tool pin profile and axial force.

scholarly journals Effect of Shoulder–Workpiece Interference Depth on the Quality of Friction Stir Welding of AA7075-T6 Aluminium Alloy

2019 ◽  
Vol 26 (1) ◽  
pp. 150-159
Author(s):  
Abbas Akram Abbas ◽  
Hazim H. Abdulkadhum
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Welding Process ◽  
High Strength ◽  
Filling Defect ◽  
Welding Quality ◽  
Left Hand ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Welding Surface

The joining of high strength aluminium alloy AA7075-T6 sheets of 3 mm thickness was an attempt utilizing friction stir welding process. The effect of interference depth between tool shoulder and surface workpiece on the welding quality and its effect on the mechanical and metallography properties of welded joints were studied. This process is carried out using a composite tool consists of a concave shoulder made of H13 tool steel and cylindrical left-hand thread with 1mm pitch pin (probe) made of cobalt-based alloy MP159. The dimensions of tools were 14mm shoulder diameter and the pin has 5mm diameter and 2.7mm length. The tool rotation speed and welding speed were 981 rpm 169 mm/min respectively, and the tilt angle was 2°. The range of interference depth between the shoulder and workpiece was selected (0.05, 0.1, 0.15, 0.2, 0.25, and 0.3) mm. various tests were executed to evaluate the welding quality. The results show that lack of filling defect appeared on the welding surface at the interference depth 0.05 mm. An invisible tunnel and lack of penetration in the bottom of the stir zone appeared when the interference depths were 0.1 mm and 0.15 mm. Defect-free welds obtained when interference depths were (0.2, 0.25, and 0.3) mm. The welding efficiency of the defect-free welds was in the range (85.3-92.3%) depending on the ultimate tensile strength of the parent alloy.

Sign in / Sign up

Export Citation Format

Share Document