scholarly journals A Review on Machine Learning Models in Injection Molding Machines

2022 ◽  
Vol 2022 ◽  
pp. 1-28
Author(s):  
Senthil Kumaran Selvaraj ◽  
Aditya Raj ◽  
R. Rishikesh Mahadevan ◽  
Utkarsh Chadha ◽  
Velmurugan Paramasivam
Keyword(s):  
Neural Network ◽  
Machine Learning ◽  
Injection Molding ◽  
Performance Criteria ◽  
Machine Learning Techniques ◽  
Injection Molding Process ◽  
Molding Process ◽  
Injection Speed ◽  
Detection Techniques ◽  
And Performance

One of the most suitable methods for the mass production of complicated shapes is injection molding due to its superior production rate and quality. The key to producing higher quality products in injection molding is proper injection speed, pressure, and mold design. Conventional methods relying on the operator’s expertise and defect detection techniques are ineffective in reducing defects. Hence, there is a need for more close control over these operating parameters using various machine learning techniques. Neural networks have considerable applications in the injection molding process consisting of optimization, prediction, identification, classification, controlling, modeling, and monitoring, particularly in manufacturing. In recent research, many critical issues in applying machine learning and neural network in injection molding in practical have been addressed. Some problems include data division, collection, and preprocessing steps, such as considering the inputs, networks, and outputs, algorithms used, models utilized for testing and training, and performance criteria set during validation and verification. This review briefly explains working on machine learning and artificial neural network and optimizing injection molding in industries.

scholarly journals Transfer Learning Applied to Characteristic Prediction of Injection Molded Products

Polymers ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3874
Author(s):  
Yan-Mao Huang ◽  
Wen-Ren Jong ◽  
Shia-Chung Chen
Keyword(s):  
Neural Network ◽  
Injection Molding ◽  
Transfer Learning ◽  
Analysis Data ◽  
Mold Temperature ◽  
Training Data ◽  
Injection Molding Process ◽  
Backpropagation Neural Network ◽  
Molding Process ◽  
Injection Speed

This study addresses some issues regarding the problems of applying CAE to the injection molding production process where quite complex factors inhibit its effective utilization. In this study, an artificial neural network, namely a backpropagation neural network (BPNN), is utilized to render results predictions for the injection molding process. By inputting the plastic temperature, mold temperature, injection speed, holding pressure, and holding time in the molding parameters, these five results are more accurately predicted: EOF pressure, maximum cooling time, warpage along the Z-axis, shrinkage along the X-axis, and shrinkage along the Y-axis. This study first uses CAE analysis data as training data and reduces the error value to less than 5% through the Taguchi method and the random shuffle method, which we introduce herein, and then successfully transfers the network, which CAE data analysis has predicted to the actual machine for verification with the use of transfer learning. This study uses a backpropagation neural network (BPNN) to train a dedicated prediction network using different, large amounts of data for training the network, which has proved fast and can predict results accurately using our optimized model.

Washers to Reduce Vibration and Noise From the Injection Molding Process

2006 ◽  
Author(s):  
Kuang-Yih Tsuei ◽  
Shu-Fen Kuo
Keyword(s):  
Injection Molding ◽  
Energy Absorption ◽  
Injection Molding Process ◽  
Performance Tests ◽  
Molding Process ◽  
Noise And Vibration ◽  
Vibration Problems ◽  
And Performance

The noise and vibration problems created by injection molding machines can be moderated by the installation of absorbers. The pull rods of the machine, which are guided to the molding movements, might be a better location for mounting a spring, rubber or hybrid elastomer for energy absorption and reduction of noise and vibration. In this paper, some special washers are designed to fit the guide rods and performance tests are carried out. The results show that noise and vibration decreased over 10 dB and 2 times, respectively.

Optimization and Design for Parameter in Injection Molding Technology of Cell Shell of Polypropylene

2011 ◽  
Vol 189-193 ◽  
pp. 537-540
Author(s):  
Jia Min Zhang ◽  
Ming Yi Zhu ◽  
Zhao Xun Lian ◽  
Rong Zhu
Keyword(s):  
Injection Molding ◽  
Injection Pressure ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Technological Parameters ◽  
Molding Process ◽  
Melt Temperature ◽  
Injection Speed ◽  
Technical Parameters ◽  
High Degree

The use of L27 (35) orthogonal to the battery shell injection molding process is optimized. The main factors of technical parameters were determined mould temperature, melt temperature, the speed of injection, injection pressure, cooling time.On the basis of actual production, to determine the factors values of different process parameters.Combination of scrapped products in key (reduction and a high degree of tolerance deflated) tests were selected in the process parameters within the scope of the assessment. Various factors impact on the product of the total height followed by cooling time, mold temperature, melt temperature, injection pressure, injection speed from strong to weak .The best products technological parameters were determined.Good results were obtained for production.

scholarly journals Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2331
Author(s):  
Chen-Yuan Chung ◽  
Shyh-Shin Hwang ◽  
Shia-Chung Chen ◽  
Ming-Chien Lai
Keyword(s):  
Injection Molding ◽  
Process Parameters ◽  
Mold Temperature ◽  
Expansion Ratio ◽  
Injection Molding Process ◽  
Molding Process ◽  
Melt Temperature ◽  
Foaming Agent ◽  
Experimental Database ◽  
Injection Speed

In the present study, semi-crystalline polypropylene (PP) and amorphous polystyrene (PS) were adopted as matrix materials. After the exothermic foaming agent azodicarbonamide was added, injection molding was implemented to create samples. The mold flow analysis program Moldex3D was then applied to verify the short-shot results. Three process parameters were adopted, namely injection speed, melt temperature, and mold temperature; three levels were set for each factor in the one-factor-at-a-time experimental design. The macroscopic effects of the factors on the weight, specific weight, and expansion ratios of the samples were investigated to determine foaming efficiency, and their microscopic effects on cell density and diameter were examined using a scanning electron microscope. The process parameters for the exothermic foaming agent were optimized accordingly. Finally, the expansion ratios of the two matrix materials in the optimal process parameter settings were compared. After the experimental database was created, the foaming module of the chemical blowing agents was established by Moldex3D Company. The results indicated that semi-crystalline materials foamed less due to their crystallinity. PP exhibits the highest expansion ratio at low injection speed, a high melt temperature, and a low mold temperature, whereas PS exhibits the highest expansion ratio at high injection speed, a moderate melt temperature, and a low mold temperature.

Robust parameter search for IC tray injection molding using regrind resin

2020 ◽  
Vol 40 (10) ◽  
pp. 876-885
Author(s):  
Ming-Shyan Huang ◽  
Shih-Chih Nian
Keyword(s):  
Injection Molding ◽  
Integrated Circuit ◽  
Pressure Profile ◽  
Injection Molding Process ◽  
Repeated Injection ◽  
Molding Process ◽  
Injection Speed ◽  
Parametric Search ◽  
Continuous Mass ◽  
Robust Parameter

AbstractQuality consistency is essential in maximizing the productivity rate of the injection molding process and minimizing the production cost. The quality consistency problem is particularly acute in the case of injection molding processes performed using regrind resin, for which the rheological properties are less uniform and more unpredictable than those of virgin material. Accordingly, the present study proposes a two-stage approach for optimizing the injection molding process parameters in such a way as to achieve a consistent molding quality over repeated injection molding cycles. In the first stage, the values of the injection speed/pressure, velocity-to-pressure (V/P) switchover point, and packing pressure are individually determined based on an inspection of the cavity pressure profile and machine parameters provided by the injection molding machine controller. In the second stage, a robust parametric search method based on a first-order regression model is employed to determine the optimal combination of the process parameter settings. Using an Integrated Circuit (IC) tray fabricated from regrind resin for illustration purposes, the results confirm that the proposed method overcomes the problem of small variations in the melt quality and therefore provides an effective technique for improving the yield rate and quality of the continuous mass production.

scholarly journals Study of an Online Monitoring Adaptive System for an Injection Molding Process Based on a Nozzle Pressure Curve

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 555
Author(s):  
Jia-Chen Fan-Jiang ◽  
Chi-Wei Su ◽  
Guan-Yan Liou ◽  
Sheng-Jye Hwang ◽  
Huei-Huang Lee ◽  
...  
Keyword(s):  
Control System ◽  
Injection Molding ◽  
Peak Pressure ◽  
Viscosity Index ◽  
Injection Molding Process ◽  
Pressure Curve ◽  
Molding Process ◽  
Injection Speed ◽  
Nozzle Pressure ◽  
Product Weight

Injection molding is a popular process for the mass production of polymer products, but due to the characteristics of the injection process, there are many factors that will affect the product quality during the long fabrication processes. In this study, an adaptive adjustment system was developed by C++ programming to adjust the V/P switchover point and injection speed during the injection molding process in order to minimize the variation of the product weight. Based on a series of preliminary experiments, it was found that the viscosity index and peak pressure had a strong correlation with the weight of the injection-molded parts. Therefore, the viscosity index and peak pressure are used to guide the adjustment in the presented control system, and only one nozzle pressure sensor is used in the system. The results of the preliminary experiments indicate that the reduction of the packing time and setting enough clamping force can decrease the variation of the injected weight without turning on the adaptive control system; meanwhile, the master pressure curve obtained from the preliminary experiment was used as the control target of the system. With this system, the variation of the product weight and coefficient of variation (CV) of the product weight can be decreased to 0.21 and 0.05%, respectively.

Sign in / Sign up

Export Citation Format

Share Document