scholarly journals A low-cost development of automatic weather station based on Arduino for monitoring precipitable water vapor

2021 ◽  
Vol 24 (2) ◽  
pp. 744
Author(s):  
Wayan Suparta ◽  
Aris Warsita ◽  
Ircham Ircham
Keyword(s):  
Water Vapor ◽  
Meteorological Data ◽  
Low Cost ◽  
Precipitable Water ◽  
Precipitable Water Vapor ◽  
Weather Station ◽  
Automatic Weather Station ◽  
Weather System ◽  
Spatial And Temporal Scales

Water vapor is the engine of the weather system. Continuous monitoring of its variability on spatial and temporal scales is essential to help improve weather forecasts. This research aims to develop an automatic weather station at low cost using an Arduino microcontroller to monitor precipitable water vapor (PWV) on a micro-scale. The surface meteorological data measured from the BME280 sensor is used to determine the PWV. Our low-cost systems also consisted of a DS3231 real-time clock (RTC) module, a 16×2 liquid crystal display (LCD) module with an I<sup>2</sup>C, and a micro-secure digital (micro-SD) card. The core of the system employed the Arduino Uno surface mount device (SMD) R3 board. The measurement results for long-term monitoring at the tested sites (ITNY and GUWO) found that the daily mean error of temperature and humidity values were 1.30% and 3.16%, respectively. While the error of air pressure and PWV were 0.092% and 2.61%, respectively. The PWV value is higher when the sun is very active or during a thunderstorm. The developed weather system is also capable of measuring altitude on pressure measurements and automatically stores daily data. With a total cost below 50 dollars, all major and support systems developed are fully functional and stable for long-term measurements.

scholarly journals Improved Drought Monitoring Index Using GNSS-Derived Precipitable Water Vapor over the Loess Plateau Area

Sensors ◽  
2019 ◽  
Vol 19 (24) ◽  
pp. 5566 ◽  
Author(s):  
Qingzhi Zhao ◽  
Xiongwei Ma ◽  
Wanqiang Yao ◽  
Yang Liu ◽  
Zheng Du ◽  
...  
Keyword(s):  
Water Vapor ◽  
Loess Plateau ◽  
Meteorological Data ◽  
Precipitable Water ◽  
Satellite System ◽  
Reanalysis Data ◽  
Precipitable Water Vapor ◽  
Drought Monitoring ◽  
The Loess Plateau ◽  
Monitoring Index

Standardized precipitation evapotranspiration index (SPEI) is an acknowledged drought monitoring index, and the evapotranspiration (ET) used to calculated SPEI is obtained based on the Thornthwaite (TH) model. However, the SPEI calculated based on the TH model is overestimated globally, whereas the more accurate ET derived from the Penman–Monteith (PM) model recommended by the Food and Agriculture Organization of the United Nations is unavailable due to the lack of a large amount of meteorological data at most places. Therefore, how to improve the accuracy of ET calculated by the TH model becomes the focus of this study. Here, a revised TH (RTH) model is proposed using the temperature (T) and precipitable water vapor (PWV) data. The T and PWV data are derived from the reanalysis data and the global navigation satellite system (GNSS) observation, respectively. The initial value of ET for the RTH model is calculated based on the TH model, and the time series of ET residual between the TH and PM models is then obtained. Analyzed results reveal that ET residual is highly correlated with PWV and T, and the correlate coefficient between PWV and ET is −0.66, while that between T and ET for cases of T larger or less than 0 °C are −0.54 and 0.59, respectively. Therefore, a linear model between ET residual and PWV/T is established, and the ET value of the RTH model can be obtained by combining the TH-derived ET and estimated ET residual. Finally, the SPEI calculated based on the RTH model can be obtained and compared with that derived using PM and TH models. Result in the Loess Plateau (LP) region reveals the good performance of the RTH-based SPEI when compared with the TH-based SPEI over the period of 1979–2016. A case analysis in April 2013 over the LP region also indicates the superiority of the RTH-based SPEI at 88 meteorological and 31 GNSS stations when the PM-based SPEI is considered as the reference.

Statistical Characteristics of Long-Term High-Resolution Precipitable Water Vapor Data at Darwin

2018 ◽  
Vol 10 (04) ◽  
pp. 1850010
Author(s):  
Kimberly Leung ◽  
Aneesh C. Subramanian ◽  
Samuel S. P. Shen
Keyword(s):  
Water Vapor ◽  
High Resolution ◽  
Southern Oscillation ◽  
Precipitable Water ◽  
Precipitable Water Vapor ◽  
Statistical Characteristics ◽  
Convective Precipitation ◽  
Data Set ◽  
Best Estimates

This paper studies the statistical characteristics of a unique long-term high-resolution precipitable water vapor (PWV) data set at Darwin, Australia, from 12 March 2002 to 28 February 2011. To understand the convective precipitation processes for climate model development, the U.S. Department of Energy’s Atmospheric Radiation Measurement (ARM) program made high-frequency radar observations of PWV at the Darwin ARM site and released the best estimates from the radar data retrievals for this time period. Based on the best estimates, we produced a PWV data set on a uniform 20-s time grid. The gridded data were sufficient to show the fractal behavior of precipitable water with Hausdorff dimension equal to 1.9. Fourier power spectral analysis revealed modulation instability due to two sideband frequencies near the diurnal cycle, which manifests as nonlinearity of an atmospheric system. The statistics of PWV extreme values and daily rainfall data show that Darwin’s PWV has El Nino Southern Oscillation (ENSO) signatures and has potential to be a predictor for weather forecasting. The right skewness of the PWV data was identified, which implies an important property of tropical atmosphere: ample capacity to hold water vapor. The statistical characteristics of this long-term high-resolution PWV data will facilitate the development and validation of climate models, particularly stochastic models.

scholarly journals Determination of zenith hydrostatic delays and the development of new global long-term GNSS-derived precipitable water vapor

2016 ◽  
Author(s):  
Xiaoming Wang ◽  
Kefei Zhang ◽  
Suqin Wu ◽  
Changyong He ◽  
Yingyan Cheng ◽  
...  
Keyword(s):  
Water Vapor ◽  
Surface Pressure ◽  
Meteorological Data ◽  
Accurate Determination ◽  
Precipitable Water ◽  
Precipitable Water Vapor ◽  
Global Navigation Satellite Systems ◽  
Average Value ◽  
Rms Errors

Abstract. Surface pressure is a vital meteorological variable for the accurate determination of precipitable water vapor (PWV) using Global Navigation Satellite Systems (GNSS). The lack of pressure observations is a big issue for the study of climate using historical GNSS observations, which is a relatively new area of GNSS applications in climatology. Hence the use of the surface pressure derived from either an empirical model (e.g. Global Pressure and Temperature 2 wet, GPT2w) or a global atmospheric reanalysis (e.g. ERA-Interim) becomes an important alternative solution. In this study, pressure derived from these two methods is compared against the pressure observed at 108 global GNSS stations for the period 2000–2013. Results show that a good accuracy is achieved from the GPT2w-derived pressure in the latitude band of −30 to 30° and the average value of Root-Mean-Square (RMS) errors across all the stations in this region is 2.4 mb. Correspondingly, an error of 5.6 mm and 1.0 mm in its resultant zenith hydrostatic delay (ZHD) and PWV is expected. In addition, GPT2w-derived pressure usually has a larger error in the cold season due to large diurnal ranges, which is not considered in the GPT2w model. The average value of the RMS errors of the ERA-Interim-derived pressure across all the 108 stations is 1.1 mb, which will lead to an equivalent error of 2.5 mm and 0.4 mm in its resultant ZHD and PWV respectively. Our research also indicates that the ERA-Interim-derived pressure has the potential to be used as a useful meteorological data source to obtain high accuracy PWV on a global scale for climate studies and the GPT2w-derived pressure can be potentially used for climatology as well although it may be only suitable for the tropical regions.

Improved Daytime Column-Integrated Precipitable Water Vapor from Vaisala Radiosonde Humidity Sensors

2008 ◽  
Vol 25 (6) ◽  
pp. 873-883 ◽  
Author(s):  
K. E. Cady-Pereira ◽  
M. W. Shephard ◽  
D. D. Turner ◽  
E. J. Mlawer ◽  
S. A. Clough ◽  
...  
Keyword(s):  
Water Vapor ◽  
Great Plains ◽  
Weather Prediction ◽  
Microwave Radiometer ◽  
Precipitable Water ◽  
Precipitable Water Vapor ◽  
Atmospheric Radiation Measurement ◽  
Atmospheric Transmittance ◽  
Dry Bias

Abstract Accurate water vapor profiles from radiosondes are essential for long-term climate prediction, weather prediction, validation of remote sensing retrievals, and other applications. The Vaisala RS80, RS90, and RS92 radiosondes are among the more commonly deployed radiosondes in the world. However, numerous investigators have shown that the daytime water vapor profiles measured by these instruments present a significant dry bias due to the solar heating of the humidity sensor. This bias in the column-integrated precipitable water vapor (PWV), along with variability due to calibration, can be removed by scaling the humidity profile to agree with the PWV retrieved from a microwave radiometer (MWR), as has been demonstrated by several previous studies. Infrared radiative closure analyses have shown that the MWR PWV does not present daytime versus nighttime differences; thus, scaling by the MWR is a possible approach for removing the daytime dry bias. However, MWR measurements are not routinely available at all radiosonde launch sites. Starting from a long-term series of sonde and MWR PWV measurements from the Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) site, the authors have developed a simple correction to the column-integrated sonde PWV, derived from an analysis of the ratio of the MWR and sonde measurements; this correction is a function of the atmospheric transmittance as determined by the solar zenith angle, and it effectively removes the daytime dry bias at all solar zenith angles. The correction was validated by successfully applying it to an independent dataset from the ARM tropical western Pacific (TWP) site.

scholarly journals Precipitable Water Vapor Retrieval from Shipborne GNSS Observations on the Korean Research Vessel ISABU

Sensors ◽  
2020 ◽  
Vol 20 (15) ◽  
pp. 4261
Author(s):  
Dong-Hyo Sohn ◽  
Byung-Kyu Choi ◽  
Yosup Park ◽  
Yoon Chil Kim ◽  
Bonhwa Ku
Keyword(s):  
Water Vapor ◽  
Low Cost ◽  
Precipitable Water ◽  
Satellite System ◽  
Precipitable Water Vapor ◽  
Dual Frequency ◽  
Gnss Receiver ◽  
Ocean Science ◽  
Rms Error ◽  
Gnss Observations

We estimate precipitable water vapor (PWV) from data collected by the low-cost Global Navigation Satellite System (GNSS) receiver at a vessel. The dual-frequency GNSS receiver that the vessel ISABU is equipped with that is operated by the Korea Institute of Ocean Science and Technology. The ISABU served in the Pacific Ocean for scientific research during a period from August 30 to September 21, 2018. It also performs radiosonde observations to obtain a vertical profile of troposphere on the vessel’s path. The GNSS-derived PWV is compared to radiosonde observations and the Atmospheric Infrared Sounder (AIRS) on NASA’s Aqua satellite output. A bias and root-mean-square (RMS) error between shipborne GNSS-PWV and radiosonde-PWV were −1.48 and 5.22 mm, respectively. When compared to the ground GNSS-PWV, shipborne GNSS-PWV has a relatively large RMS error in comparison with radiosonde-PWV. However, the GNSS observations on the vessel are still in good agreement with radiosonde observations. On the other hand, the GNSS-PWV is not well linearly correlated with AIRS-PWV. The RMS error between the two observations was approximately 8.97 mm. In addition, we showed that the vessel on the sea surface has significantly larger carrier phase multipath error compared to the ground-based GNSS observations. This also can result in reducing the accuracy of shipborne GNSS-PWV. However, we suggest that the shipborne GNSS has sufficient potential to derive PWV with the kinematic precise point positioning (PPP) solution on the vessel.

scholarly journals Constructing Precipitable Water Vapor Map from Regional GNSS Network Observations without Collocated Meteorological Data

2018 ◽  
Author(s):  
Biyan Chen ◽  
Wujiao Dai ◽  
Zhizhao Liu ◽  
Lixin Wu ◽  
Cuilin Kuang ◽  
...  
Keyword(s):  
Water Vapor ◽  
Meteorological Data ◽  
Precipitable Water ◽  
Satellite System ◽  
Precipitable Water Vapor ◽  
Weighted Mean Temperature ◽  
Synoptic Observations ◽  
Gnss Network ◽  
Gnss Data ◽  
Better Than

Abstract. Surface pressure (Ps) and weighted mean temperature (Tm) are two necessary variables for the accurate retrieval of precipitable water vapor (PWV) from global navigation satellite system (GNSS) data. The lack of Ps or Tm information is a concern for those GNSS sites that are not collocated with meteorological sensors. This paper investigates an alternative method of inferring accurate Ps and Tm at the GNSS station using nearby synoptic observations. Ps and Tm obtained at the nearby synoptic sites are interpolated onto the location of GNSS station by performing both vertical and horizontal adjustments, in which the parameters involved in Ps and Tm calculation are estimated from ERA-Interim reanalysis profiles. In addition, we present a method of constructing high quality PWV map through vertical reduction and horizontal interpolation of the retrieved GNSS PWVs. To evaluate the performances of the Ps and Tm retrieval and the PWV map construction, GNSS data collected from 58 stations of the Hunan GNSS network and synoptic observations from 20 nearby sites in 2015 were processed to extract the PWV so as to subsequently generate PWV map. The retrieved Ps and Tm and constructed PWV maps were assessed by the results derived from radiosonde and ERA-Interim reanalysis. The results show that (1) accuracies of Ps and Tm derived by synoptic interpolation are within the range of 1.7–3.0 hPa and 2.5–3.0 K, respectively, which are much better than the GPT2w model; (2) the constructed PWV maps have good agreements with radiosonde and ERA reanalysis data with overall accuracy better than 3 mm; and (3) PWV maps can well reveal the moisture advection, transportation and convergence during heavy rainfall.

scholarly journals Constructing a precipitable water vapor map from regional GNSS network observations without collocated meteorological data for weather forecasting

2018 ◽  
Vol 11 (9) ◽  
pp. 5153-5166 ◽  
Author(s):  
Biyan Chen ◽  
Wujiao Dai ◽  
Zhizhao Liu ◽  
Lixin Wu ◽  
Cuilin Kuang ◽  
...  
Keyword(s):  
Water Vapor ◽  
Weather Forecasting ◽  
Meteorological Data ◽  
Precipitable Water ◽  
Precipitable Water Vapor ◽  
Total Delay ◽  
Weighted Mean Temperature ◽  
Synoptic Observations ◽  
Gnss Network ◽  
Better Than

Abstract. Surface pressure (Ps) and weighted mean temperature (Tm) are two necessary variables for the accurate retrieval of precipitable water vapor (PWV) from Global Navigation Satellite System (GNSS) zenith total delay (ZTD) estimates. The lack of Ps or Tm information is a concern for those GNSS sites that are not collocated with meteorological sensors. This paper investigates an alternative method of inferring accurate Ps and Tm at the GNSS station using nearby synoptic observations. Ps and Tm obtained at the nearby synoptic sites are interpolated onto the location of the GNSS station by performing both vertical and horizontal adjustments, in which the parameters involved in Ps and Tm calculation are estimated from ERA-Interim reanalysis profiles. In addition, we present a method of constructing high-quality PWV maps through vertical reduction and horizontal interpolation of the retrieved GNSS PWVs. To evaluate the performances of the Ps and Tm retrieval, and the PWV map construction, GNSS data collected from 58 stations of the Hunan GNSS network and synoptic observations from 20 nearby sites in 2015 were processed to extract the PWV so as to subsequently generate the PWV maps. The retrieved Ps and Tm and constructed PWV maps were assessed by the results derived from radiosonde and the ERA-Interim reanalysis. The results show that (1) accuracies of Ps and Tm derived by synoptic interpolation are within the range of 1.7–3.0 hPa and 2.5–3.0 K, respectively, which are much better than the GPT2w model; (2) the constructed PWV maps have good agreements with radiosonde and ERA-Interim reanalysis data with the overall accuracy being better than 3 mm; and (3) PWV maps can well reveal the moisture advection, transportation and convergence during heavy rainfall.

Estimation of Missing GPS Precipitable Water Vapor Data by Zenith Wet Delay and Meteorological Data

2014 ◽  
Vol 931-932 ◽  
pp. 703-708
Author(s):  
Prawit Uang-Aree ◽  
Sununtha Kingpaiboon ◽  
Kulyakorn Khuanmar
Keyword(s):  
Water Vapor ◽  
Linear Regression ◽  
Vapor Pressure ◽  
Surface Temperature ◽  
Meteorological Data ◽  
Water Vapor Pressure ◽  
Precipitable Water ◽  
Precipitable Water Vapor ◽  
Dew Point ◽  
Zenith Wet Delay

This article presents a statistical correlation between GPS precipitable water vapor and meteorological data, i.e., surface temperature, air pressure, relative humidity, dew point temperature, and water vapor pressure by using linear regression. The data, recorded over a 4-year period, was used as an estimation of missing GPS precipitable water vapor data from discontinuous recordings. A multiple linear regression equation showed a correlation among zenith wet delay (ZWD), water vapor pressure (e) and surface temperature (T) was ZWD(e,T) = 17.4952e-0.8281T-93.164, with a coefficient of determination (R2) of 0.725, a mean absolute error of 8.71 mm, a root mean square error of 10.39 mm, and a mean absolute percentage error of 18.63%. The equation obtained can be used to estimate GPS precipitable water vapor data which is missing from recordings due to accident or technological error.

Sign in / Sign up

Export Citation Format

Share Document