Adhesion strength of copper thin-films to a E24 carbon steel: effects of substrate surface ion bombardment etching

1993 ◽  
Vol 7 (2) ◽  
pp. 141-157 ◽  
Author(s):  
M. Cailler ◽  
A. Ouis ◽  
P.J. Schultz ◽  
P.J. Simpson
Keyword(s):  
Thin Films ◽  
Carbon Steel ◽  
Adhesion Strength ◽  
Substrate Surface ◽  
Ion Bombardment

Development of preferred orientation in polycrystalline AlN thin films deposited by rf sputtering system at low temperature

1997 ◽  
Vol 12 (7) ◽  
pp. 1850-1855 ◽  
Author(s):  
A. Rodríguez-Navarro ◽  
W. Otaño-Rivera ◽  
J. M. García-Ruiz ◽  
R. Messier ◽  
L. J. Pilione
Keyword(s):  
Thin Films ◽  
Gas Phase ◽  
Incidence Angle ◽  
Substrate Surface ◽  
Rf Sputtering ◽  
Ion Bombardment ◽  
Preferred Orientation ◽  
Glass Substrates ◽  
Crystal Twinning ◽  
Sputtering System

The development of preferred orientation in AlN thin films deposited on silica glass substrates by rf sputtering at low substrate temperature (<150 °C) has been studied. The main factors controlling the preferential orientation of the AlN thin films are the ion-bombardment energies, incidence angle of the arriving particles, and deposition rate. At low pressure, a perpendicular and highly directional energetic ion-bombardment induces an orientation of the crystallites with their c-axis perpendicular to the substrate surface. At higher pressure (>15 mTorr), a spreading in the incidence angle of the arriving particles, due to gas phase collisions, favors the formation of AlN crystal twinning. A change in the preferred orientation of the films from (0001) to (1011) for deposition rates above 1.8 Å/s is observed.

Observations on the growth of YBa2Cu3O7-δ thin films on MgO by pulsed-laser ablation

1991 ◽  
Vol 49 ◽  
pp. 1068-1069
Author(s):  
M. Grant Norton ◽  
C. Barry Carter
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Laser Ablation ◽  
Substrate Surface ◽  
Pulsed Laser ◽  
Pulsed Laser Ablation ◽  
Thin Film Deposition ◽  
Film Deposition ◽  
Laser Ablation Process ◽  
Deposition Parameters

Pulsed-laser ablation has been widely used to produce high-quality thin films of YBa2Cu3O7-δ on a range of substrate materials. The nonequilibrium nature of the process allows congruent deposition of oxides with complex stoichiometrics. In the high power density regime produced by the UV excimer lasers the ablated species includes a mixture of neutral atoms, molecules and ions. All these species play an important role in thin-film deposition. However, changes in the deposition parameters have been shown to affect the microstructure of thin YBa2Cu3O7-δ films. The formation of metastable configurations is possible because at the low substrate temperatures used, only shortrange rearrangement on the substrate surface can occur. The parameters associated directly with the laser ablation process, those determining the nature of the process, e g. thermal or nonthermal volatilization, have been classified as ‘primary parameters'. Other parameters may also affect the microstructure of the thin film. In this paper, the effects of these ‘secondary parameters' on the microstructure of YBa2Cu3O7-δ films will be discussed. Examples of 'secondary parameters' include the substrate temperature and the oxygen partial pressure during deposition.

Ion Beam Mixing of Ni-Ti Bilayered Thin Films

1985 ◽  
Vol 43 ◽  
pp. 290-291
Author(s):  
A. K. Rai ◽  
R. S. Bhattacharya ◽  
M. H. Rashid
Keyword(s):  
Crystal Structure ◽  
Thin Films ◽  
Amorphous Alloys ◽  
Ion Beam ◽  
Ion Bombardment ◽  
High Energy ◽  
Mixing Efficiency ◽  
Ion Beam Mixing ◽  
Enhanced Diffusion ◽  
Binary Metal

Ion beam mixing has recently been found to be an effective method of producing amorphous alloys in the binary metal systems where the two original constituent metals are of different crystal structure. The mechanism of ion beam mixing are not well understood yet. Several mechanisms have been proposed to account for the observed mixing phenomena. The first mechanism is enhanced diffusion due to defects created by the incoming ions. Second is the cascade mixing mechanism for which the kinematicel collisional models exist in the literature. Third mechanism is thermal spikes. In the present work we have studied the mixing efficiency and ion beam induced amorphisation of Ni-Ti system under high energy ion bombardment and the results are compared with collisional models. We have employed plan and x-sectional veiw TEM and RBS techniques in the present work.

{10} edge dislocations in YSZ films grown on (100)MgO by PLD

1994 ◽  
Vol 52 ◽  
pp. 530-531
Author(s):  
Jason R. Heffelfinger ◽  
C. Barry Carter
Keyword(s):  
Thin Films ◽  
Semiconductor Lasers ◽  
Vapor Deposition ◽  
Substrate Surface ◽  
Laser System ◽  
Average Energy ◽  
Target Material ◽  
Chemical Vapor ◽  
Buffer Layers ◽  
Organic Chemical

Yttria-stabilized zirconia (YSZ) is currently used in a variety of applications including oxygen sensors, fuel cells, coatings for semiconductor lasers, and buffer layers for high-temperature superconducting films. Thin films of YSZ have been grown by metal-organic chemical vapor deposition, electrochemical vapor deposition, pulse-laser deposition (PLD), electron-beam evaporation, and sputtering. In this investigation, PLD was used to grow thin films of YSZ on (100) MgO substrates. This system proves to be an interesting example of relationships between interfaces and extrinsic dislocations in thin films of YSZ.In this experiment, a freshly cleaved (100) MgO substrate surface was prepared for deposition by cleaving a lmm-thick slice from a single-crystal MgO cube. The YSZ target material which contained 10mol% yttria was prepared from powders and sintered to 85% of theoretical density. The laser system used for the depositions was a Lambda Physik 210i excimer laser operating with KrF (λ=248nm, 1Hz repetition rate, average energy per pulse of 100mJ).

Epitaxial Growth of Sr0.3Ba0.7Nb2O6 Thin Films Prepared by Sol-Gel Process

1999 ◽  
Vol 606 ◽  
Author(s):  
Keishi Nishio ◽  
Jirawat Thongrueng ◽  
Yuichi Watanabe ◽  
Toshio Tsuchiya
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Epitaxial Growth ◽  
Raw Materials ◽  
Substrate Surface ◽  
Sol Gel ◽  
Tungsten Bronze ◽  
Monomethyl Ether ◽  
Tetragonal Tungsten Bronze ◽  
Sol Gel Process

AbstructWe succeeded in the preparation of strontium-barium niobate (Sr0.3Ba0.7Nb2O6 : SBN30)that have a tetragonal tungsten bronze type structure thin films on SrTiO3 (100), STO, or La doped SrTiO3 (100), LSTO, single crystal substrates by a spin coating process. LSTO substrate can be used for electrode. A homogeneous coating solution was prepared with Sr and Ba acetates and Nb(OEt)5 as raw materials, and acetic acid and diethylene glycol monomethyl ether as solvents. The coating thin films were sintered at temperature from 700 to 1000°C for 10 min in air. It was confirmed that the thin films on STO substrate sintered above 700°C were in the epitaxial growth because the 16 diffraction spots were observed on the pole figure using (121) reflection. The <130> and <310> direction of the thin film on STO were oriented with the c-axis in parallel to the substrate surface. However, the diffraction spots of thin film on LSTO substrate sintered at 700°C were corresponds to the expected pattern for (110).

The Correlation of Adhesion Strength with Barrier Structure in Cu Metallization

2003 ◽  
Vol 766 ◽  
Author(s):  
A. Sekiguchi ◽  
J. Koike ◽  
K. Ueoka ◽  
J. Ye ◽  
H. Okamura ◽  
...  
Keyword(s):  
Thin Films ◽  
Adhesion Strength ◽  
Nitrogen Concentration ◽  
Scratch Test ◽  
Barrier Structure ◽  
Barrier Layers ◽  
Cu Metallization ◽  
Microstructure Observation ◽  
Sputter Deposited ◽  
Sulfur Containing

AbstractAdhesion strength in sputter-deposited Cu thin films on various types of barrier layers was investigated by scratch test. The barrier layers were Ta1-xNx with varied nitrogen concentration of 0, 0.2, 0.3, and 0.5. Microstructure observation by TEM indicated that each layer consists of mixed phases of β;-Ta, bcc-TaN0.1, hexagonal-TaN, and fcc-TaN, depending on the nitrogen concentration. A sulfur- containing amorphous phase was also present discontinuously at the Cu/barrier interfaces in all samples. Scratch test showed that delamination occurred at the Cu/barrier interface and that the overall adhesion strength increased with increasing the nitrogen concentration. A good correlation was found between the measured adhesion strength and the composing phases in the barrier layer.

Improvement of Adhesion Strength of Fluoropolymer Thin Films by Vapor Deposition Polymerization

2013 ◽  
Vol E96.C (3) ◽  
pp. 374-377 ◽  
Author(s):  
Kazuo SENDA ◽  
Tsuyoshi MATSUDA ◽  
Kuniaki TANAKA ◽  
Hiroaki USUI
Keyword(s):  
Thin Films ◽  
Adhesion Strength ◽  
Vapor Deposition

Observations on the Growth of YBa2Cu3O7 Thin Films at Very High Laser Fluences

1995 ◽  
Vol 388 ◽  
Author(s):  
Rand R. Biggers. ◽  
M. Grant Norton ◽  
I. Maartense ◽  
T.L. Peterson ◽  
E. K. Moser ◽  
...  
Keyword(s):  
Thin Films ◽  
Substrate Surface ◽  
Chemical Vapor ◽  
Growth Conditions ◽  
Organic Chemical ◽  
High Fluences ◽  
Laser Fluences ◽  
High Laser ◽  
High Laser Fluences ◽  
Very High

AbstractThe pulsed-laser deposition (PLD) technique utilizes one of the most energetic beams available to form thin films of the superconducting oxide YBa2Cu3O7 (YBCO). IN this study we examine the growth of YBCO at very high laser fluences (25 to 40 J/cm2); a more typical fluence for PLD would be nearer to 3 J/cm2. the use of high fluences leads to unique film microstructures which, in some cases, appear to be related to the correspondingly higher moveabilities of the adatoms. Films grown on vicinal substrates, using high laser fluences, exhibited well-defined elongated granular morphologies (with excellent transition temperature, Tc, and critical current density, Jc). Films grown on vicinal substrates using off-axis magnetron sputtering, plasma-enhanced metal organic chemical vapor deposition (PE-MOCVD), or PLD at more typical laser fluences showed some similar morphologies, but less well-defined. Under certain growth conditions, using high laser fluences with (001) oriented substrates, the YBCO films can exhibit a mixture of a- and c-axis growth where both crystallographic orientations nucleate on the substrate surface at the same time, and grow in concert. the ratio of a-axis oriented to c-axis oriented grains is strongly affected by the pulse repetition rate of the laser.

Sign in / Sign up

Export Citation Format

Share Document