scholarly journals Infrared Interferometric Measurements of the Near-Surface Air Temperature over the Oceans

2005 ◽  
Vol 22 (7) ◽  
pp. 1019-1032 ◽  
Author(s):  
P. J. Minnett ◽  
K. A. Maillet ◽  
J. A. Hanafin ◽  
B. J. Osborne
Keyword(s):  
Air Temperature ◽  
Surface Air Temperature ◽  
The Arctic ◽  
Heat Island ◽  
Radiometric Measurement ◽  
Near Surface ◽  
Air Temperatures ◽  
Wide Range ◽  
Marine Air ◽  
The Tropical Pacific

Abstract The radiometric measurement of the marine air temperature using a Fourier transform infrared spectroradiometer is described. The measurements are taken by the Marine-Atmospheric Emitted Radiance Interferometer (M-AERI) that has been deployed on many research ships in a wide range of conditions. This approach is inherently more accurate than conventional techniques and can be used to determine some of the error characteristics of the standard measurements. Examples are given from several cruises ranging from the Arctic to the equatorial Pacific Oceans. It is shown that the diurnal heating signal in radiometric air temperatures in the tropical Pacific can typically reach an amplitude of ∼15% of that measured by conventional sensors. Conventional data have long been recognized as being contaminated by direct solar heating and heat island effects of the ships or buoys on which they are mounted, but here this effect is quantified by comparisons with radiometric measurements.

scholarly journals An Evaluation of HIRS Near-Surface Air Temperature Product in the Arctic with SHEBA Data

2016 ◽  
Vol 33 (3) ◽  
pp. 453-460 ◽  
Author(s):  
Ge Peng ◽  
Lei Shi ◽  
Steve T. Stegall ◽  
Jessica L. Matthews ◽  
Christopher W. Fairall
Keyword(s):  
Air Temperature ◽  
Heat Budget ◽  
Surface Air Temperature ◽  
Correlation Coefficients ◽  
Remote Sensing Data ◽  
The Arctic ◽  
Near Surface ◽  
Brightness Temperatures ◽  
Uncertainty Sources ◽  
Air Temperatures

AbstractThe accuracy of cloud-screened 2-m air temperatures derived from the intersatellite-calibrated brightness temperatures based on the High Resolution Infrared Radiation Sounder (HIRS) measurements on board the National Oceanic and Atmospheric Administration (NOAA) Polar-Orbiting Operational Environmental Satellite (POES) series is evaluated by comparing HIRS air temperatures to 1-yr quality-controlled measurements collected during the Surface Heat Budget of the Arctic Ocean (SHEBA) project (October 1997–September 1998). The mean error between collocated HIRS and SHEBA 2-m air temperature is found to be on the order of 1°C, with a slight sensitivity to spatial and temporal radii for collocation. The HIRS temperatures capture well the temporal variability of SHEBA temperatures, with cross-correlation coefficients higher than 0.93, all significant at the 99.9% confidence level. More than 87% of SHEBA temperature variance can be explained by linear regression of collocated HIRS temperatures. The analysis found a strong dependency of mean temperature errors on cloud conditions observed during SHEBA, indicating that availability of an accurate cloud mask in the region is essential to further improve the quality of HIRS near-surface air temperature products. This evaluation establishes a baseline of accuracy of HIRS temperature retrievals, providing users with information on uncertainty sources and estimates. It is a first step toward development of a new long-term 2-m air temperature product in the Arctic that utilizes intersatellite-calibrated remote sensing data from the HIRS instrument.

scholarly journals Polar Amplification and Ice Free Conditions under 1.5, 2 and 3 °C of Global Warming as Simulated by CMIP5 and CMIP6 Models

Atmosphere ◽  
2021 ◽  
Vol 12 (11) ◽  
pp. 1494
Author(s):  
Fernanda Casagrande ◽  
Francisco A. B. Neto ◽  
Ronald B. de Souza ◽  
Paulo Nobre
Keyword(s):  
Global Warming ◽  
Temperature Response ◽  
Surface Air Temperature ◽  
The Arctic ◽  
Polar Regions ◽  
High Latitudes ◽  
Near Surface ◽  
Polar Amplification ◽  
Air Temperatures ◽  
Average Rise

One of the most visible signs of global warming is the fast change in the polar regions. The increase in Arctic temperatures, for instance, is almost twice as large as the global average in recent decades. This phenomenon is known as the Arctic Amplification and reflects several mutually supporting processes. An equivalent albeit less studied phenomenon occurs in Antarctica. Here, we used numerical climate simulations obtained from CMIP5 and CMIP6 to investigate the effects of +1.5, 2 and 3 °C warming thresholds for sea ice changes and polar amplification. Our results show robust patterns of near-surface air-temperature response to global warming at high latitudes. The year in which the average air temperatures brought from CMIP5 and CMIP6 models rises by 1.5 °C is 2024. An average rise of 2 °C (3 °C) global warming occurs in 2042 (2063). The equivalent warming at northern (southern) high latitudes under scenarios of 1.5 °C global warming is about 3 °C (1.8 °C). In scenarios of 3 °C global warming, the equivalent warming in the Arctic (Antarctica) is close to 7 °C (3.5 °C). Ice-free conditions are found in all warming thresholds for both the Arctic and Antarctica, especially from the year 2030 onwards.

Quantifying heating biases in marine air temperature observations, ~1790 - present

2021 ◽  
Author(s):  
Thomas Cropper ◽  
Elizabeth Kent ◽  
David Berry ◽  
Richard Cornes ◽  
Beatriz Recinos-Rivas
Keyword(s):  
Air Temperature ◽  
Diurnal Cycle ◽  
Surface Air Temperature ◽  
Night Time ◽  
Data Set ◽  
Near Surface ◽  
Marine Surface ◽  
Heating Model ◽  
Marine Air

<p>Accurate, long-term time series of near-surface air temperature (AT) are the fundamental datasets on which the magnitude of anthropogenic climate change is scientifically and societally addressed. Across the ocean, these (near-surface) climate records use Sea Surface Temperature (SST) instead of Marine Air Temperature (MAT) and blend the SST and AT over land to create datasets. MAT has often been overlooked as a data choice as daytime MAT observations from ships are known to contain warm biases due to the storage of accumulated solar energy. Two recent MAT datasets, CLASSnmat (1881 – 2019) and UAHNMAT (1900 – 2018), both use night-time MAT observations only. Daytime MAT observations in the International Comprehensive Ocean–Atmosphere Data Set (ICOADS) account for over half of the MAT observations in ICOADS, and this proportion increases further back in time (i.e. pre-1850s). If long-term MAT records over the ocean are to be extended, the use of daytime MAT is vital.</p><p> </p><p>To adjust for the daytime MAT heating bias, and apply it to ICOADS, we present the application of a physics-based model, which accounts for the accumulated energy storage throughout the day. As the ‘true’ diurnal cycle of MAT over the ocean has not been, to-date, adequately quantified, our approach also removes the diurnal cycle from ICOADS observations and generates a night-time equivalent MAT for all observations. We fit this model to MAT observations from groups of ships in ICOADS that share similar heating biases and metadata characteristics. This enables us to use the empirically derived coefficients (representing the physical energy transfer terms of the heating model) obtained from the fit for use in removal of the heating bias and diurnal cycle from ship-based MAT observations throughout ICOADS which share similar characteristics (i.e. we can remove the diurnal cycle from a ship which only reports once daily at noon). This adjustment will create an MAT record of night-time-equivalent temperatures that will enable an extension of the marine surface AT record back into the 18<sup>th</sup> century.</p>

Study on Urban Thermal Environment based on Diurnal Temperature Range

2020 ◽  
Author(s):  
Zheng Guo ◽  
Miaomiao Cheng
Keyword(s):  
Surface Temperature ◽  
Air Temperature ◽  
Land Surface Temperature ◽  
Land Surface ◽  
Thermal Environment ◽  
Surface Air Temperature ◽  
Heat Island ◽  
Near Surface ◽  
Diurnal Range ◽  
Urban Thermal Environment

<p>Diurnal temperature range (includes land surface temperature diurnal range and near surface air temperature diurnal range) is an important meteorological parameter, which is a very important factor in the field of the urban thermal environmental. Nowadays, the research of urban thermal environment mainly focused on surface heat island and canopy heat island.</p><p>Based on analysis of the current status of city thermal environment. Firstly, a method was proposed to obtain near surface air temperature diurnal range in this study, difference of land surface temperature between day and night were introduced into the improved temperature vegetation index feature space based on remote sensing data. Secondly, compared with the district administrative division, we analyzed the spatial and temporal distribution characteristics of the diurnal range of land surface temperature and near surface air temperature.</p><p>The conclusions of this study are as follows:</p><p>1 During 2003-2012s, the land surface temperature and near surface air temperature diurnal range of Beijing were fluctuating upward. The rising trend of the near surface air temperature diurnal range was more significant than land surface temperature diurnal range. In addition, the rise and decline of land surface temperature and near surface air temperature diurnal range in different districts were different. In the six city districts, the land surface temperature and near surface air temperature diurnal range in the six areas of the city were mainly downward. The decline trend of near surface air temperature diurnal range was more significant than land surface temperature diurnal range.</p><p>2 During 2003-2012s, the land surface temperature and near surface air temperature diurnal range of Beijing with similar characteristics in spatial distribution, with higher distribution land surface temperature and near surface air temperature diurnal range in urban area and with lower distribution of land surface temperature and near surface air temperature diurnal range in the Northwest Mountainous area and the area of Miyun reservoir.</p>

scholarly journals An evaluation of the impact of aerosol particles on weather forecasts from a biomass burning aerosol event over the Midwestern United States: observational-based analysis of surface temperature

2016 ◽  
Vol 16 (10) ◽  
pp. 6475-6494 ◽  
Author(s):  
Jianglong Zhang ◽  
Jeffrey S. Reid ◽  
Matthew Christensen ◽  
Angela Benedetti
Keyword(s):  
United States ◽  
Air Temperature ◽  
Surface Air Temperature ◽  
Cooling Efficiency ◽  
Surface Cooling ◽  
Near Surface ◽  
Smoke Aerosol ◽  
Weather Forecasts ◽  
Air Temperatures ◽  
Daily Changes

Abstract. A major continental-scale biomass burning smoke event from 28–30 June 2015, spanning central Canada through the eastern seaboard of the United States, resulted in unforecasted drops in daytime high surface temperatures on the order of 2–5  °C in the upper Midwest. This event, with strong smoke gradients and largely cloud-free conditions, provides a natural laboratory to study how aerosol radiative effects may influence numerical weather prediction (NWP) forecast outcomes. Here, we describe the nature of this smoke event and evaluate the differences in observed near-surface air temperatures between Bismarck (clear) and Grand Forks (overcast smoke), to evaluate to what degree solar radiation forcing from a smoke plume introduces daytime surface cooling, and how this affects model bias in forecasts and analyses. For this event, mid-visible (550 nm) smoke aerosol optical thickness (AOT, τ) reached values above 5. A direct surface cooling efficiency of −1.5 °C per unit AOT (at 550 nm, τ550) was found. A further analysis of European Centre for Medium-Range Weather Forecasts (ECMWF), National Centers for Environmental Prediction (NCEP), United Kingdom Meteorological Office (UKMO) near-surface air temperature forecasts for up to 54 h as a function of Moderate Resolution Imaging Spectroradiometer (MODIS) Dark Target AOT data across more than 400 surface stations, also indicated the presence of the daytime aerosol direct cooling effect, but suggested a smaller aerosol direct surface cooling efficiency with magnitude on the order of −0.25 to −1.0 °C per unit τ550. In addition, using observations from the surface stations, uncertainties in near-surface air temperatures from ECMWF, NCEP, and UKMO model runs are estimated. This study further suggests that significant daily changes in τ550 above 1, at which the smoke-aerosol-induced direct surface cooling effect could be comparable in magnitude with model uncertainties, are rare events on a global scale. Thus, incorporating a more realistic smoke aerosol field into numerical models is currently less likely to significantly improve the accuracy of near-surface air temperature forecasts. However, regions such as eastern China, eastern Russia, India, and portions of the Saharan and Taklamakan deserts, where significant daily changes in AOTs are more frequent, are likely to benefit from including an accurate aerosol analysis into numerical weather forecasts.

scholarly journals Suitability of a constant air temperature lapse rate over an Alpine glacier: testing the Greuell and Böhm model as an alternative

2013 ◽  
Vol 54 (63) ◽  
pp. 120-130 ◽  
Author(s):  
Lene Petersen ◽  
Francesca Pellicciotti ◽  
Inge Juszak ◽  
Marco Carenzo ◽  
Ben Brock
Keyword(s):  
Air Temperature ◽  
Surface Air Temperature ◽  
Ambient Air ◽  
Lapse Rate ◽  
Spatial And Temporal Variability ◽  
Near Surface ◽  
Alpine Glacier ◽  
Temperature Lapse Rate ◽  
Boundary Layer Height ◽  
Air Temperatures

AbstractNear-surface air temperature, typically measured at a height of 2 m, is the most important control on the energy exchange and the melt rate at a snow or ice surface. It is distributed in a simplistic manner in most glacier melt models by using constant linear lapse rates, which poorly represent the actual spatial and temporal variability of air temperature. In this paper, we test a simple thermodynamic model proposed by Greuell and Böhm in 1998 as an alternative, using a new dataset of air temperature measurements from along the flowline of Haut Glacier d’Arolla, Switzerland. The unmodified model performs little better than assuming a constant linear lapse rate. When modified to allow the ratio of the boundary layer height to the bulk heat transfer coefficient to vary along the flowline, the model matches measured air temperatures better, and a further reduction of the root-mean-square error is obtained, although there is still considerable scope for improvement. The modified model is shown to perform best under conditions favourable to the development of katabatic winds – few clouds, positive ambient air temperature, limited influence of synoptic or valley winds and a long fetch – but its performance is poor under cloudy conditions.

scholarly journals The Influence of Tropical Pacific SST Anomaly on Surface Air Temperature in China

2014 ◽  
Vol 27 (4) ◽  
pp. 1425-1444 ◽  
Author(s):  
XiaoJing Jia ◽  
Hai Lin ◽  
Xia Yao
Keyword(s):  
Pacific Ocean ◽  
Air Temperature ◽  
Numerical Models ◽  
Surface Air Temperature ◽  
Tropical Pacific ◽  
The Arctic ◽  
Seasonal Forecasts ◽  
Climate Trend ◽  
Atmospheric Component ◽  
The Tropical Pacific

Abstract The influence of the tropical Pacific sea surface temperature (SST) on the wintertime surface air temperature (SAT) in China is investigated using both the observational data and the output of coupled ocean–atmosphere numerical models during the period from 1960 to 2006. A singular value decomposition analysis (SVD) is applied between 500-hPa geopotential height (Z500) in the Northern Hemisphere and SST in the tropical Pacific Ocean to get the tropical Pacific SST-forced atmospheric patterns. The association of the SAT over China and the tropical Pacific SST is measured by calculating the temporal correlation coefficient (TCC) between the SAT and the expansion coefficient of the atmospheric component of the leading two SVD modes. Results show that the SAT over China is significantly correlated to the second SVD mode (SVD2). The SST component of SVD2 is characterized by negative tropical Pacific SST anomalies centered over the midequatorial Pacific Ocean. The atmospheric component of SVD2 (ASVD2) shares many similarities in spatial structures to the Arctic Oscillation (AO). The time variation of ASVD2, however, is found more closely correlated to the variation of SAT over China than the AO. When SVD2 is in its positive phase, the SAT over China tends to be warmer than normal. Further analysis indicates that the TCC between the SAT in China and ASVD2 is largely decreased after the long-term climate trend is removed. The time variability of the tropical Pacific SST-forced large-scale atmospheric patterns and its relationship to SAT are reasonably captured by the multimodel ensemble (MME) seasonal forecasts. An examination of the MME forecast skill indicates that ASVD2 contributes significantly to the TCC skill of MME forecasts.

scholarly journals Estimating urban heat island effects on near-surface air temperature records of Uccle (Brussels, Belgium): an observational and modeling study

2011 ◽  
Vol 6 (1) ◽  
pp. 27-34 ◽  
Author(s):  
R. Hamdi ◽  
H. Van de Vyver
Keyword(s):  
Remote Sensing ◽  
Urban Heat Island ◽  
Air Temperature ◽  
Surface Air Temperature ◽  
Heat Island ◽  
Urban Bias ◽  
Near Surface ◽  
Urban Warming ◽  
Urban Heat ◽  
Weather Stations

Abstract. In this letter, the Brussels's urban heat island (UHI) effect on the near-surface air temperature time series of Uccle (the national suburban recording station of the Royal Meteorological Institute of Belgium) was estimated between 1955 and 2006 during the summer months. The UHI of Brussels was estimated using both ground-based weather stations and remote sensing imagery combined with a land surface scheme that includes a state-of-the-art urban parameterization, the Town Energy Balance scheme. Analysis of urban warming based on the remote sensing method reveals that the urban bias on minimum air temperature is rising at a higher rate, 2.5 times (2.85 ground-based observed) more, than on maximum temperature, with a linear trend of 0.15 °C (0.19 °C ground-based observed) and 0.06 °C (0.06 °C ground-based observed) per decade respectively. The summer-mean urban bias on the mean air temperature is 0.8 °C (0.9 °C ground-based observed). The results based on remote sensing imagery are compatible with estimates of urban warming based on weather stations. Therefore, the technique presented in this work is a useful tool in estimating the urban heat island contamination in long time series, countering the drawbacks of an ground-observational approach.

scholarly journals Simultaneous assessment of the summer urban heat island in Moscow megacity based on in situ observations, thermal satellite images and mesoscale modeling

2019 ◽  
Vol 12 (4) ◽  
pp. 74-95 ◽  
Author(s):  
Mikhail I. Varentsov ◽  
Mikhail Y. Grishchenko ◽  
Hendrik Wouters
Keyword(s):  
Remote Sensing ◽  
Spatial Structure ◽  
Urban Heat Island ◽  
Air Temperature ◽  
Surface Air Temperature ◽  
Atmospheric Model ◽  
Heat Island ◽  
Near Surface ◽  
Urban Heat

This study compares three popular approaches to quantify the urban heat island (UHI) effect in Moscow megacity in a summer season (June-August 2015). The first approach uses the measurements of the near-surface air temperature obtained from weather stations, the second is based on remote sensing from thermal imagery of MODIS satellites, and the third is based on the numerical simulations with the mesoscale atmospheric model COSMO-CLM coupled with the urban canopy scheme TERRA_URB. The first approach allows studying the canopy-layer UHI (CLUHI, or anomaly of a near- surface air temperature), while the second allows studying the surface UHI (SUHI, or anomaly of a land surface temperature), and both types of the UHI could be simulated by the atmospheric model. These approaches were compared in the daytime, evening and nighttime conditions. The results of the study highlight a substantial difference between the SUHI and CLUHI in terms of the diurnal variation and spatial structure. The strongest differences are found at the daytime, at which the SUHI reaches the maximal intensity (up to 10°С) whereas the CLUHI reaches the minimum intensity (1.5°С). However, there is a stronger consistency between CLUHU and SUHI at night, when their intensities converge to 5–6°С. In addition, the nighttime CLUHI and SUHI have similar monocentric spatial structure with a temperature maximum in the city center. The presented findings should be taken into account when interpreting and comparing the results of UHI studies, based on the different approaches. The mesoscale model reproduces the CLUHI-SUHI relationships and provides good agreement with in situ observations on the CLUHI spatiotemporal variations (with near-zero biases for daytime and nighttime CLUHI intensity and correlation coefficients more than 0.8 for CLUHI spatial patterns). However, the agreement of the simulated SUHI with the remote sensing data is lower than agreement of the simulated CLUHI with in situ measurements. Specifically, the model tends to overestimate the daytime SUHI intensity. These results indicate a need for further in-depth investigation of the model behavior and SUHI–CLUHI relationships in general.

scholarly journals An energy budget approach to understand the Arctic warming during the Last Interglacial

2021 ◽  
Author(s):  
Marie Sicard ◽  
Masa Kageyama ◽  
Sylvie Charbit ◽  
Pascale Braconnot ◽  
Jean-Baptiste Madeleine
Keyword(s):  
Sea Ice ◽  
Arctic Ocean ◽  
Air Temperature ◽  
Energy Budget ◽  
Surface Air Temperature ◽  
The Arctic ◽  
Last Interglacial ◽  
Near Surface ◽  
Arctic Warming ◽  
The Arctic Ocean

Abstract. The Last Interglacial period (129–116 ka BP) is characterized by a strong orbital forcing which leads to a different seasonal and latitudinal distribution of insolation compared to the pre-industrial period. In particular, these changes amplify the seasonality of the insolation in the high latitudes of the northern hemisphere. Here, we investigate the Arctic climate response to this forcing by comparing the CMIP6 lig127k and pi-Control simulations performed with the IPSL-CM6A-LR model. Using an energy budget framework, we analyse the interactions between the atmosphere, ocean, sea ice and continents. In summer, the insolation anomaly reaches its maximum and causes a near-surface air temperature rise of 3.2 °C over the Arctic region. This warming is primarily due to a strong positive surface downwelling shortwave radiation anomaly over continental surfaces, followed by large heat transfers from the continents back to the atmosphere. The surface layers of the Arctic Ocean also receives more energy, but in smaller quantity than the continents due to a cloud negative feedback. Furthermore, while heat exchanges from the continental surfaces towards the atmosphere are strengthened, the ocean absorbs and stores the heat excess due to a decline in sea ice cover. However, the maximum near-surface air temperature anomaly does not peak in summer like insolation, but occurs in autumn with a temperature increase of 4.0 °C relative to the pre-industrial period. This strong warming is driven by a positive anomaly of longwave radiations over the Arctic ocean enhanced by a positive cloud feedback. It is also favoured by the summer and autumn Arctic sea ice retreat (−1.9 × 106 and −3.4 × 106 km2 respectively), which exposes the warm oceanic surface and allows heat stored by the ocean in summer and water vapour to be released. This study highlights the crucial role of the sea ice cover variations, the Arctic ocean, as well as changes in polar clouds optical properties on the Last Interglacial Arctic warming.

Sign in / Sign up

Export Citation Format

Share Document