Tensile behaviors of co-woven-knitted fabric reinforced composites under various strain rates

2011 ◽  
Vol 45 (24) ◽  
pp. 2495-2506 ◽  
Author(s):  
Pibo Ma ◽  
Hong Hu ◽  
Lvtao Zhu ◽  
Baozhong Sun ◽  
Bohong Gu
Keyword(s):  
Strain Rate ◽  
Failure Modes ◽  
Shear Failure ◽  
High Strain ◽  
Tensile Failure ◽  
Knitted Fabric ◽  
Strain Rates ◽  
High Strain Rates ◽  
Textile Composite ◽  
Interface Failure

This article reports the tensile behaviors of a novel kind of 3D textile composite, named as co-woven-knitted fabric (CWKF) reinforced composite, under quasi-static and high strain rates. The tensile tests were conducted along the warp direction (0°), bias direction (45°), and weft direction (90°) at quasi-static strain rate of 0.001/s and high strain rates ranging from 1589/s to 2586/s. The results indicate that the tensile strength, failure strain, tensile stiffness, energy absorption, and resilient energy are strain rate sensitive along all the three directions. The relationships between the mechanical parameters and the strain rate were also analyzed. The fractograph of the CWKF composite demonstrate that the tensile failure modes are matrix shear failure and fibers breakage under the quasi-static testing condition while interface failure and fibers pullout are at high strain rates.

Impact tensile behavior and frequency response of 3D braided composites

2011 ◽  
Vol 82 (3) ◽  
pp. 280-287 ◽  
Author(s):  
Xuehui Gan ◽  
Jianhua Yan ◽  
Bohong Gu ◽  
Baozhong Sun
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Tensile Properties ◽  
High Strain ◽  
Tensile Modulus ◽  
Tensile Failure ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Braided Composites ◽  
3D Braided Composites

The uniaxial tensile properties of 4-step 3D braided E-glass/epoxy composites under quasi-static and high-strain rate loadings have been investigated to evaluate the tensile failure mode at different strain rates. The uniaxial tensile properties at high strain rates from 800/s to 2100/s were tested using the split Hopkinson tension bar (SHTB) technique. The tensile properties at quasi-static strain rate were also tested and compared with those in high strain rates. Z-transform theory is applied to 3D braided composites to characterize the system dynamic behaviors in frequency domain. The frequency responses and the stability of 3D braided composites under quasi-static and high-strain rate compression have been analyzed and discussed in the Z-transform domain. The results indicate that the stress-strain curves are rate sensitive, and tensile modulus, maximum tensile stress and corresponding tensile strain are also sensitive to the strain rate. The tensile modulus, maximum tensile stress of the 3D braided composites are linearly increased with the strain rate. With increasing of the strain rate (from 0.001/s to 2100/s), the tensile failure of the 3D braided composite specimens has a tendency of transition from ductile failure to brittle failure. The magnitude response and phase response is very different in quasi-static loading with that in high-strain rate loading. The 3D braided composite system is more stable at high strain rate than quasi-static loading.

A Dynamic Mechanical Analysis of T2 Copper at High Strain Rates

2019 ◽  
Vol 812 ◽  
pp. 38-44
Author(s):  
Shuai Chen ◽  
Wen Bin Li ◽  
Xiao Ming Wang ◽  
Wen Jin Yao
Keyword(s):  
Yield Strength ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Pure Copper ◽  
Dislocation Slip ◽  
Strain Rates ◽  
High Strain Rates ◽  
Stress Strain ◽  
Shpb Test

This work compares the pure copper (T2 copper)’s stress-strain relationship at different strain rates in the uni-axial tension test and Split Hopkinson Pressure Bar (SHPB) test. Small samples were utilized in the high strain rate SHPB test in which the accuracy was modified by numerical simulation. The experimental results showed that the T2 copper’s yield strength at high strain rates largely outweighed the quasi static yield strength. The flow stress in the stress-strain curves at different strain rates appeared to be divergent and increased with the increase in strain rates, showing great strain strengthening and strain rate hardening effects. Metallographic observation showed that the microstructure of T2 copper changed from equiaxed grains to twins and the interaction between the dislocation slip zone grain boundary and twins promoted the super plasticity distortion in T2 copper.

Comparative Study of the Dynamic Behavior of AA2519 Aluminum Alloy in T6 and T8 Temper Conditions

2019 ◽  
Author(s):  
Adewale Olasumboye ◽  
Gbadebo Owolabi ◽  
Olufemi Koya ◽  
Horace Whitworth ◽  
Nadir Yilmaz
Keyword(s):  
Plastic Deformation ◽  
Aluminum Alloy ◽  
Stress Response ◽  
Flow Stress ◽  
Yield Strength ◽  
Strain Rate ◽  
High Strain ◽  
Second Phase ◽  
Strain Rates ◽  
High Strain Rates

Abstract This study investigates the dynamic response of AA2519 aluminum alloy in T6 temper condition during plastic deformation at high strain rates. The aim was to determine how the T6 temper condition affects the flow stress response, strength properties and microstructural morphologies of the alloy when impacted under compression at high strain rates. The specimens (with aspect ratio, L/D = 0.8) of the as-cast alloy used were received in the T8 temper condition and further heat-treated to the T6 temper condition based on the standard ASTM temper designation procedures. Split-Hopkinson pressure bar experiment was used to generate true stress-strain data for the alloy in the range of 1000–3500 /s strain rates while high-speed cameras were used to monitor the test compliance with strain-rate constancy measures. The microstructures of the as received and deformed specimens were assessed and compared for possible disparities in their initial microstructures and post-deformation changes, respectively, using optical microscopy. Results showed no clear evidence of strain-rate dependency in the dynamic yield strength behavior of T6-temper designated alloy while exhibiting a negative trend in its flow stress response. On the contrary, AA2519-T8 showed marginal but positive response in both yield strength and flow behavior for the range of strain rates tested. Post-deformation photomicrographs show clear disparities in the alloys’ initial microstructures in terms of the second-phase particle size differences, population density and, distribution; and in the morphological changes which occurred in the microstructures of the different materials during large plastic deformation. AA2519-T6 showed a higher susceptibility to adiabatic shear localization than AA2519-T8, with deformed and bifurcating transformed band occurring at 3000 /s followed by failure at 3500 /s.

scholarly journals An Image-Based Impact Test for the High Strain Rate Tensile Properties of Brittle Materials

2018 ◽  
Vol 183 ◽  
pp. 02042
Author(s):  
Lloyd Fletcher ◽  
Fabrice Pierron
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
High Strain Rate ◽  
Strain Rate ◽  
Stress Wave ◽  
High Strain ◽  
Brittle Materials ◽  
Test Method ◽  
Strain Rates ◽  
High Strain Rates

Testing ceramics at high strain rates presents many experimental diffsiculties due to the brittle nature of the material being tested. When using a split Hopkinson pressure bar (SHPB) for high strain rate testing, adequate time is required for stress wave effects to dampen out. For brittle materials, with small strains to failure, it is difficult to satisfy this constraint. Because of this limitation, there are minimal data (if any) available on the stiffness and tensile strength of ceramics at high strain rates. Recently, a new image-based inertial impact (IBII) test method has shown promise for analysing the high strain rate behaviour of brittle materials. This test method uses a reflected compressive stress wave to generate tensile stress and failure in an impacted specimen. Throughout the propagation of the stress wave, full-field displacement measurements are taken, from which strain and acceleration fields are derived. The acceleration fields are then used to reconstruct stress information and identify the material properties. The aim of this study is to apply the IBII test methodology to analyse the stiffness and strength of ceramics at high strain rates. The results show that it is possible to identify the elastic modulus and tensile strength of tungsten carbide at strain rates on the order of 1000 s-1. For a tungsten carbide with 13% cobalt binder the elastic modulus was identified as 516 GPa and the strength was 1400 MPa. Future applications concern boron carbide and sapphire, for which limited data exist in high rate tension.

Compressive Behavior of Plain and Fiber-Reinforced High-Strength Concrete Subjected to High Strain Rate Loading

2011 ◽  
Vol 82 ◽  
pp. 57-62 ◽  
Author(s):  
Sha Sha Wang ◽  
Min Hong Zhang ◽  
Ser Tong Quek
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strength Concrete ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Strain Rates ◽  
Compressive Behavior ◽  
High Strain Rates ◽  
Strength Concrete

This paper presents a laboratory experimental study on the effect of high strain rate on compressive behavior of plain and fiber-reinforce high-strength concrete (FRHSC) with similar strength of 80-90 MPa. Steel fibers, polyethylene fibers, and a combination of these were used in the FRHSC. A split Hopkinson pressure bar equipment was used to determine the concrete behavior at strain rates from about 30 to 300 s-1. The ratio of the strength at high strain rates to that at static loading condition, namely dynamic increase factor (DIF), of the concretes was determined and compared with that recommended by CEB-FIP code. Fracture patterns of the specimens at high strain rates are described and discussed as well. Results indicate that the CEB-FIP equation is applicable to the plain high strength concrete, but overestimates the DIF of the FRHSC at strain rates beyond a transition strain rate of 30 s-1. Based on the experimental results, a modified equation on DIF is proposed for the FRHSC.

Experimental Studies of the Behaviour at High Strain Rates of Unfilled and Filled Polypropylenes

2006 ◽  
Vol 3-4 ◽  
pp. 363-368 ◽  
Author(s):  
N. Temimi ◽  
Noelle Billon
Keyword(s):  
Strain Rate ◽  
High Speed ◽  
High Strain ◽  
Experimental Studies ◽  
Young Modulus ◽  
Video Camera ◽  
Image Correlation ◽  
Strain Rates ◽  
High Strain Rates ◽  
Low Velocity

Thermo mechanical behaviour of unfilled and filled polypropylenes are studied in tension from 10-4 to 102 s-1. Complementary low velocity compression and shear tests are also performed. A high-speed video camera (up to 2500 frames/s) combined with image analysis, image correlation and an infra red pyrometer allow measuring 3D-strain fields and temperature during tests. Thus, data can be processed without restrictive assumptions. Beside usual (for polymers) temperature and strain rate sensitivities it is found that plastic deformation in these materials does not obey incompressibility assumption. Voiding damage is evidenced in the polymer matrix by SEM observations that result in volume change and significant decrease in Young modulus for both materials. Moreover, an increase in the temperature of more than 10 °C is observed and is likely to modify the behaviour of each material at high strain rates. Shear and compression measurements demonstrate that yield criteria and constitutive equation depend on loading. It is concluded that apparent yield stress in semi-crystalline polypropylene can be a result of a combination of “non strain rate sensitive” “non-cohesive mechanisms” and “strain rate sensitive” “cohesive mechanisms”. Experimental characterisation on polymers should then be revisited as most of the usual assumptions are invalid and non monotonic tests should be generalized.

Inspection of Adiabatic Shear Bands in High Manganese TRIP Steels

2013 ◽  
Vol 753 ◽  
pp. 72-75 ◽  
Author(s):  
Hui Zhen Wang ◽  
Xiu Rong Sun ◽  
Ping Yang ◽  
Wei Min Mao
Keyword(s):  
Shear Failure ◽  
High Strain ◽  
Shear Bands ◽  
Adiabatic Shear ◽  
Strain Rates ◽  
Trip Effect ◽  
Adiabatic Shear Bands ◽  
High Manganese ◽  
High Strain Rates ◽  
Trip Steels

Adiabatic shear bands (ASBs) develop generally during high strain rates. This paper investigates the transformation induced plasticity (TRIP) effect during ASBs formation at high strain rates in high manganese TRIP steels containing initial austenite and ferrite by EBSD technique. Results show that TRIP effect takes place mainly before the formation of ASBs. After ASBs formation, TRIP effect is strongly restricted by the size effect, the increase of stacking fault energy (SFE) and even inverse martensitic transformation due to the rise of temperature. The TRIP effect before ASBs formation contributes to the resistance of adiabatic shear failure. Dynamic recrystallization driven by subgrains rotation occurs within ASBs, and ultrafine grains often show strong shear textures with twin relationship owing to slip mechanism.

Strain Rate Effects and Rate-Dependent Constitutive Models of Lead-Based and Lead-Free Solders

2009 ◽  
Vol 77 (1) ◽  
Author(s):  
Fei Qin ◽  
Tong An ◽  
Na Chen
Keyword(s):  
Strain Rate ◽  
Impact Analysis ◽  
Solder Joints ◽  
High Strain ◽  
Drop Impact ◽  
Lead Free ◽  
Strain Rates ◽  
High Strain Rates ◽  
Rate Dependent ◽  
Lead Free Solders

As traditional lead-based solders are banned and replaced by lead-free solders, the drop impact reliability is becoming increasingly crucial because there is little understanding of mechanical behaviors of these lead-free solders at high strain rates. In this paper, mechanical properties of one lead-based solder, Sn37Pb, and two lead-free solders, Sn3.5Ag and Sn3.0Ag0.5Cu, were investigated at strain rates that ranged from 600 s−1 to 2200 s−1 by the split Hopkinson pressure and tensile bar technique. At high strain rates, tensile strengths of lead-free solders are about 1.5 times greater than that of the Sn37Pb solder, and also their ductility are significantly greater than that of the Sn37Pb. Based on the experimental data, strain rate dependent Johnson–Cook models for the three solders were derived and employed to predict behaviors of solder joints in a board level electronic package subjected to standard drop impact load. Results indicate that for the drop impact analysis of lead-free solder joints, the strain rate effect must be considered and rate-dependent material models of lead-free solders are indispensable.

Sign in / Sign up

Export Citation Format

Share Document