Fabrication of superhydrophobic cotton fabrics through wrapping silica with plasma-induced grafting polymerization

2017 ◽  
Vol 89 (3) ◽  
pp. 401-410 ◽  
Author(s):  
Yongqiang Li ◽  
Chao Zou ◽  
Jianzhong Shao ◽  
Ya’nan Li
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Cotton Fabric ◽  
Photoelectron Spectroscopy ◽  
Contact Angle Measurement ◽  
Cotton Fabrics ◽  
Angle Measurement ◽  
Water Contact ◽  
Washing Durability ◽  
Before And After

Cotton fabric is commonly used in daily life, but it is easily wetted and contaminated by liquid. Herein, we present a simple and environmentally friendly plasma technology for hydrophobic modification of cotton fabric. In order to endow superhydrophobicity to cotton fabric, helium plasma inducing graft polymerization of 1,3,5,7-tetravinyl-1,3,5,7-tetramethylcyclotetrasiloxane (D4Vi) was utilized to wrap SiO2 particles on cotton fabrics. Cotton fabrics were successively dipped in silica sol and D4Vi, then treated by plasma. Cotton fabrics before and after modification were characterized by using field emission scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and water contact angle measurement. The experimental results showed that the cotton-SiO2-D4Vi consisted of nanoscale SiO2 protrusions and low-surface-energy film polymerized by D4Vi. In addition, the one wrapped SiO2 of 161 nm presented excellent hydrophobicity, washing durability, and repellency toward different types of liquids with a water contact angle of 152°.

scholarly journals Superhydrophobic organosilicon-based coating system by a novel ultravoilet-curable method

2017 ◽  
Vol 7 ◽  
pp. 184798041770279 ◽  
Author(s):  
Baojiang Liu ◽  
Taizhou Tian ◽  
Jinlong Yao ◽  
Changgen Huang ◽  
Wenjun Tang ◽  
...  
Keyword(s):  
Contact Angle ◽  
Surface Energy ◽  
Silica Nanoparticles ◽  
Water Contact Angle ◽  
Cotton Fabric ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Water Repellent ◽  
Step Method ◽  
Water Contact

A robust superhydrophobic organosilica sol-gel-based coating on a cotton fabric substrate was successfully fabricated via a cost-effective one-step method. The coating was prepared by modification of silica nanoparticles with siloxane having long alkyl chain that allow to reduce surface energy. The coating on cotton fabric exhibited water contact angle of 151.6°. The surface morphology was evaluated by scanning electron microscopy, and surface chemical composition was measured with X-ray photoelectron spectroscopy. Results showed the enhanced superhydrophobicity that was attributed to the synergistic effect of roughness created by the random distribution of silica nanoparticles and the low surface energy imparted of long-chain alkane siloxane. In addition, the coating also showed excellent durability against washing treatments. Even after washed for 30 times, the specimen still had a water contact angle of 130°, indicating an obvious water-repellent property. With this outstanding property, the robust superhydrophobic coating exhibited a prospective application in textiles and plastics.

Effect of Plasma-Induced Polymerization on Contact Angle of Paper

2011 ◽  
Vol 396-398 ◽  
pp. 1619-1623
Author(s):  
Zhao Ping Song ◽  
Jun Rong Li ◽  
Hui Ning Xiao
Keyword(s):  
Contact Angle ◽  
Photoelectron Spectroscopy ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Polymer Grafting ◽  
Hydrophobic Property ◽  
Cellulose Fibres ◽  
Water Contact ◽  
X Ray ◽  
Factors Associated

Hydrophobic modification of cellulose fibres was conducted by plasma-induced polymer grafting in an attempt to increase the hydrophobicity of paper. Two hydrophobic monomers, i.e., butyl acrylate (BA) and 2-ethylhexyl acrylate (2-EHA) were grafted on cellulose fibres, induced by atmospheric cold plasma. Various influencing factors associated with the plasma-induced grafting were investigated, including the contact time and reaction temperature with monomers, and the dosage of monomers. Contact-angle measurement, infrared spectrum (IR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM) were used to ascertain the occurrence of the grafting. The results showed that the hydrophobic property of the modified paper sheet was improved significantly after the plasma-induced grafting. The water contact angle on the surface of the paper reached up to higher than125°.

Picoliter Water Contact Angle Measurement on Polymers

Langmuir ◽  
2007 ◽  
Vol 23 (13) ◽  
pp. 6875-6878 ◽  
Author(s):  
Michael Taylor ◽  
Andrew J. Urquhart ◽  
Mischa Zelzer ◽  
Martyn C. Davies ◽  
Morgan R. Alexander
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Water Contact ◽  
Water Contact Angle Measurement

Contact Angle Analysis on Glass Based Surface

2014 ◽  
Vol 680 ◽  
pp. 93-96
Author(s):  
Muhammad Hafiz Ab Aziz ◽  
Zaliman Sauli ◽  
Vithyacharan Retnasamy ◽  
Wan Mokhdzani Wan Norhaimi ◽  
Steven Taniselass ◽  
...  
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Hydrophobic Surface ◽  
Soda Lime ◽  
Sample Surface ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Anodic Bonding ◽  
Soda Lime Glass ◽  
Water Contact

This paper reports on the contact angle measurement analysis on a glass based surface for anodic bonding process cleaned by three distinct cleaning processes. The three types of glass based surface used were silica, pyrex, and soda lime glass. The three cleaning solutions tested in this experiment were RCA, piranha and acetone. Water Droplet Test (WDT) was done to analyze the contact angle of micro droplet on sample surface. It can be done by dropping a droplet of water in constant volume at the fixed height and angle. Only RCA process constantly decreases the contact angle value after cleaning. The compilations of data strongly proved that all samples become hydrophilic after RCA cleaning process. The solid surface is considered hydrophilic when water contact angle is smaller than 90°, and hydrophobic profile if the water contact angle is larger than 90°. Samples which undergo piranha and acetone cleaning did not prove any characteristic of hydrophilic or hydrophobic surface after cleaning.

Preparation and Characterization of Plasma-Treated Porous Poly(glycerol sebacate) Scaffolds

2013 ◽  
Vol 747 ◽  
pp. 182-185
Author(s):  
Tharinee Theerathanagorn ◽  
Boonlom Thavornyutikarn ◽  
Wanida Janvikul
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Photoelectron Spectroscopy ◽  
Average Molecular Weight ◽  
Sebacic Acid ◽  
Angle Measurement ◽  
Porous Scaffolds ◽  
Hydroxyl Groups ◽  
Condensation Polymerization ◽  
Water Contact

In this study, poly (glycerol sebacate) (PGS) was initially synthesized via condensation polymerization of glycerol and sebacic acid at equimolar ratio (1:1) at 130°C for 24 h. The number average molecular weight (Mn) of the resulting polymer determined by gel permeation chromatography (GPC) was about 2800 g/mol. Porous PGS scaffolds were subsequently prepared by a particle-leaching technique. NaCl was added into the polymer at 60-90% w/w; the mixtures were cured in Teflon molds at 140°C for 16 h. The porous scaffolds were further subjected to surface treatment with low pressure oxygen plasma to increase surface carboxyl and hydroxyl groups and thereby enhance hydrophilicity of PGS scaffold surface. The surface morphology and wettability of both untreated PGS and plasma-treated PGS scaffolds were comparatively determined by scanning electron microscopy (SEM) and water contact angle measurement, respectively. A considerable decrease in water contact angle was observed on the PGS scaffolds after the plasma treatment. The surface chemistry, mechanical strength and degree of swelling of the PGS scaffolds were also assessed by X-ray photoelectron spectroscopy (XPS), dynamic mechanical analysis (DMA) and swelling measurement, respectively.

scholarly journals Fabrication and characterization of superhydrophobic and superlipophilic silica nanofibers mats with excellent heat resistance

2016 ◽  
Vol 52 (1) ◽  
pp. 87-92 ◽  
Author(s):  
S. Gao ◽  
H. Watanabe ◽  
K. Nakane ◽  
K. Zhao
Keyword(s):  
Contact Angle ◽  
Heat Resistance ◽  
Photoelectron Spectroscopy ◽  
Treatment Time ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
High Specific Surface Area ◽  
Water Contact ◽  
Water Filter ◽  
Silica Nanofibers

A kind of silica nanofibers (SNF) mats with superhydrophobicity and superlipophilicity as well as excellent heat resistance, had been prepared by modifying of 1, 1, 1, 3, 3, 3-hexamethyldisilazane on electrospun SNF mats. The effects of heat treatment time on properties of modified SNF mats were investigated by scanning electron microscopy, nitrogen absorption analysis, X-ray photoelectron spectroscopy, and contact angle measurement. With high specific surface area 240.1 m2/g, the optimal modified SNF mat approached water contact angle (WCA) 153.2? and fuel contact angle (FCA) 0?, furthermore, even after annealing by 450?C in air for 1h , WCA remained at 135.5? and FCA kept at 3.8?, which opened a new way to improve heat resistance of fuel-water filter paper.

scholarly journals Preparation and Characterization of a Hydrophilic Polysulfone Membrane Using Graphene Oxide

2019 ◽  
Vol 2019 ◽  
pp. 1-10 ◽  
Author(s):  
Hoan Thi Vuong Nguyen ◽  
Thu Hong Anh Ngo ◽  
Khai Dinh Do ◽  
Minh Ngoc Nguyen ◽  
Nu Thi To Dang ◽  
...  
Keyword(s):  
Contact Angle ◽  
Graphene Oxide ◽  
Water Contact Angle ◽  
Water Flux ◽  
Feed Solution ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Inversion Method ◽  
Water Contact ◽  
Polysulfone Membrane

In general, the polysulfone (PSf) membranes are popular choices for water treatment because they have high thermal stability and good chemical resistance. On the other hand, the filtration capacity of the polysulfone membrane is limited because of its low water flux and poor antifouling ability, which are caused by the low surface hydrophilicity of the membranes. In this research, blending of graphene oxide (GO) or graphene oxide-titanium dioxide (GO-TiO2) mixture into the polysulfone matrix had been carried out through the phase inversion method to enhance the hydrophilic and antifouling properties. Methods such as energy-dispersive X-ray spectroscopy, scanning electron microscopy, Fourier transform infrared spectroscopy, and water contact angle measurement were used to examine the surface properties of the prepared membranes. Experimental results have led to a conclusion that graphene oxide can be stabilized into prepared membranes, and then, by reducing the water contact angle values, the surface of these membranes becomes hydrophilic, which increases the permeability and the water flux of methylene blue from the aqueous feed solution, improving the membrane’s antifouling resistance.

Adsorption of Hyperbranched Polysiloxysilane Modified with Triethoxy Group onto the Silicon Wafer

2007 ◽  
Vol 19 (5-6) ◽  
pp. 700-710 ◽  
Author(s):  
Yasuko Yamada ◽  
Tomoyasu Hirai ◽  
Ryohei Kikuchi ◽  
Teruaki Hayakawa ◽  
Masa-Aki Kakimoto
Keyword(s):  
Contact Angle ◽  
Silicon Wafer ◽  
Photoelectron Spectroscopy ◽  
Dynamic Contact Angle ◽  
Dynamic Contact ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Wafer Surface ◽  
Water Contact ◽  
Silicon Wafer Surface

Triethoxysilyl functionalized hyperbranched polsiloxysilanes at the focal (FT-HBPSs) and terminal (TT-HBPSs) positions were synthesized to investigate adsorption behavior onto a silicon wafer surface. The surface of the silicon wafer adsorbed with the HBPSs was characterized by X-ray photoelectron spectroscopy, atomic force microscopy (AFM), static and dynamic water contact angle measurements. The AFM images indicated the formation size of dot-like structures were approximately 200 nm. The presence of vinyl terminal groups of FT-HBPSs permitted conversion of the surface from a non-polar hydrocarbon to a polar hydroxylated or carboxylated structures. After the polarity was changed, the surface properties were also studied using the above surface analysis techniques. The dynamic contact angle measurement indicated that the silicon wafer surface modified by FT-HBPSs was more hydrophilic in water than TT-HBPS. This behavior can be explained by the difference of connecting points between HBPS and the silicon wafer surface.

scholarly journals Surface treated cotton fabric with stain repellent property for the use in aircraft upholstery

2021 ◽  
Vol 16 ◽  
pp. 155892502110051
Author(s):  
Kuruppu Achchige Dulani Daminda Kuruppu
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Cotton Fabric ◽  
Textile Industry ◽  
Water Contact ◽  
Wrinkle Resistance ◽  
Static Water Contact Angle ◽  
Before And After ◽  
Static Water ◽  
Afm Micrographs

Nanotechnology modifications play a major role in textile industry due to extraordinary properties exhibit in fabrics due to nanomaterials. It offers different functionalities namely self-cleaning, wrinkle resistance, flame retardancy, protection from UV radiations or antibacterial property. Further, it is important to maintain cleanliness in aircraft upholstery always but the airliners have to bear a considerable amount of money to clean up the aircraft upholstery. Interestingly, nanotechnology can provide stain repellence property for fabrics in aircraft upholstery. This study covers a method of developing a stain repellent fabric which was stable even after 25 standard laundering conditions. In this study nanotechnology was used to modify a cotton fabric with stain repellant property. After nanotechnology modification, the surface wettability of the treated fabrics was characterized by static water contact angle measurements before and after 25 washes carried out under standard laundering conditions. Similar testings were carried out for the untreated fabric samples. The static water contact angle for the treated fabric was 161° with the recovery of 97.5% after 25 washing cycles. SEM and AFM micrographs were used to analyze the coatings. Further, the stability of hydrophobicity in the modified cotton fabric after 25 washes was also tested for tea, coffee, and water solutions which are vulnerable stain types in aircraft upholstery. It clearly proved that the modified cotton fabric even after 25 washes showed hydrophobicity for tea, coffee, and water. Therefore, it could be concluded that the developed modified cotton fabric can consider to be used as an aircraft upholstery.

Sign in / Sign up

Export Citation Format

Share Document