Optimization of process parameters for friction stir welding of joining A6061 and A6082 alloys by Taguchi method

2012 ◽  
Vol 227 (6) ◽  
pp. 1150-1163 ◽  
Author(s):  
Sanjay Kumar ◽  
Sudhir Kumar ◽  
Ajay Kumar
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Experimental Tests ◽  
Dissimilar Joints ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Optimization Of Process Parameters ◽  
Tool Pin

The friction stir welding is a pioneering solid-state metal joining technique for producing high-quality joints in materials. In this article, Taguchi approach is applied to analyze the optimal process parameters for optimum tensile strength and hardness of welded dissimilar A6061 and A6082 alloys. An orthogonal array of L9 is implemented and the analysis of variance is employed to investigate the importance of parameters on responses. The experimental tests, conducted according to combination of rotational speed, tool tilt and types of tool pin profile parameters. The results indicate that the rotational speed is most significant process parameter that has the highest influence on tensile strength and hardness, followed by tool pin profile and tool tilt. The optimum results verified by conducting confirmation experiments. The predicted optimal value of tensile strength and hardness of dissimilar joints produced by friction stir welding are 267.74 MPa and 80.55 HRB, respectively.

Optimization of friction stir welding process parameters for AA6063-ETP copper using central composite design

2020 ◽  
Vol 17 (4) ◽  
pp. 491-507 ◽  
Author(s):  
Nitin Panaskar ◽  
Ravi Prakash Terkar
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Content Type ◽  
Friction Stir ◽  
Central Composite

Purpose Recently, several studies have been performed on lap welding of aluminum and copper using friction stir welding (FSW). The formation of intermetallic compounds at the weld interface hampers the weld quality. The use of an intermediate layer of a compatible material during welding reduces the formation of intermetallic compounds. The purpose of this paper is to optimize the FSW process parameters for AA6063-ETP copper weld, using a compatible zinc intermediate filler metal. Design/methodology/approach In the present study, a three-level, three-factor central composite design (CCD) has been used to determine the effect of various process parameters, namely, tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil on ultimate tensile strength of the weld. A total of 60 experimental data were fitted in the CCD. The experiments were performed with tool rotational speeds of 1,000, 1,200 and 1,400 rpm each of them with tool traverse speeds of 5, 10 and 15 mm/min. A zinc inter-filler foil of 0.2 and 0.4 mm was also used. The macrograph of the weld surface under different process parameters and the tensile strength of the weld have been investigated. Findings The feasibility of joining 3 mm thick AA6063-ETP copper using zinc inter-filler is established. The regression analysis showed a good fit of the experimental data to the second-order polynomial model with a coefficient of determination (R2) value of 0.9759 and model F-value of 240.33. A good agreement between the prediction model and experimental findings validates the reliability of the developed model. The tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil significantly affected the tensile strength of the weld. The optimal conditions found for the weld were, rotational speed of 1,212.83 rpm and traverse speed of 9.63 mm/min and zinc foil thickness is 0.157 mm; by using optimized values, ultimate tensile strength of 122.87 MPa was achieved, from the desirability function. Originality/value Aluminium and copper sheets could be joined feasibly using a zinc inter-filler. The maximum tensile strength of joints formed by inter-filler (122.87 MPa) was significantly better as compared to those without using inter-filler (83.78 MPa). The optimum process parameters to achieve maximum tensile strength were found by CCD.

Effect of Tool pin Profile and Axial Force on Tensile Behavior in Friction Stir Welding of Dissimilar Aluminum Alloys

2011 ◽  
Vol 415-417 ◽  
pp. 1140-1146 ◽  
Author(s):  
R. Palanivel ◽  
P. Koshy Mathews ◽  
M. Balakrishnan ◽  
I. Dinaharan ◽  
N. Murugan
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Axial Force ◽  
Aluminium Alloys ◽  
Welding Process ◽  
Fusion Welding ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Dissimilar Aluminum Alloys ◽  
Tool Pin

Aluminium alloys generally has low weldability by traditional fusion welding process. The development of the Friction Stir Welding (FSW) has provided an alternative improved way of producing aluminium joints, in a faster and reliable manner. FSW process has several advantages, in particular the possibility to weld dissimilar aluminium alloys. This study focuses on the behavior of tensile strength of dissimilar joints of AA6351-T6 alloy to AA5083-H111 alloy produced by friction stir welding was analysed. Five different tool pin profile such as Straight Square (SS), Tapered Square (TS), Straight Hexagon (SH), Straight Octagon (SO) and Tapered Octagon (TO) with three different axial force (1tonne, 1.5tonne, 2 tonne) have been used to weld the joints. The effect of pin profiles and axial force on tensile properties and material flow behaviour of the joint was analyzed and it was found that the straight square pin profile with 1.5 tonne produced better tensile strength then other tool pin profile and axial force.

Process Parameters Optimization of Friction Stir Welding in Aluminium Alloy 6063-T6 by Taguchi Method

2017 ◽  
Vol 867 ◽  
pp. 97-104 ◽  
Author(s):  
T. Ganapathy ◽  
K. Lenin ◽  
K. Pannerselvam
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Taguchi Method ◽  
Axial Force ◽  
Process Parameters ◽  
Welding Speed ◽  
Rotational Speed ◽  
Process Parameter ◽  
Main Process ◽  
Friction Stir

This paper deals with the effective application of friction stir welding similar to butt joining technique.AL6063 T-6 alloys prepared in 125x 100 x 7mm thickness plate and FSW tool setup were H13 of diameter 25mm rotary tool with straight cylindrical pin profile. The maximum strength was considered for selection of combined process parameter. The process parameters were optimized using Taguchi method. The Rotational speed, welding speed, and axial speed are the main process parameter which taken into our consideration. The optimum process parameters are determined with reference to tensile strength of the joint. From the experiments, it was found the effects of welding parameter are the axial force is highest substantial parameter to determining the tensile strength of the joint. The paper which revealed the optimal values of process parameter are to acquire a maximum tensile strength of friction stir welded AL6063-T6 plates is 101.6Mpa with the combination level of rotational speed, welding speed and axial force are found to be 1100 RPM, 60 mm/min and 12.5 KN. validation test was carried out and results were nearer to the optimized results confirmed by the optimum results.

Parameters optimization in FSW of polypropylene based on RSM

2015 ◽  
Vol 11 (1) ◽  
pp. 32-42 ◽  
Author(s):  
K Panneerselvam ◽  
Kasirajan Lenin
Keyword(s):  
Process Parameters ◽  
Rotational Speed ◽  
Optimization Techniques ◽  
Parameters Optimization ◽  
Tool Rotational Speed ◽  
Content Type ◽  
Friction Stir ◽  
Optimization Of Process Parameters ◽  
Output Characteristics ◽  
Tool Pin

Purpose – The purpose of this paper is to weld polypropylene (PP) material by friction stir welding (FSW) process. The input process parameters considered were: tool pin profile, feed rate and tool rotational speed and the process output characteristics were tensile strength, Shore-D hardness, Rockwell hardness, Izod strength, Charpy strength and nugget area. Design/methodology/approach – Optimization of process parameters were carried out based on response surface methodology (RSM) and significant parameters were obtained by performing analysis of variance (ANOVA). Findings – The optimized results were the threaded pin profile for feed of 60 mm/min and tool rotational speed of 1,500 rpm. A confirmation test was carried out to verify the optimized results. Originality/value – In this paper, the process parameters were optimized based on RSM. This is newly adopted optimization techniques in the FSW process of PP materials and also it gives better results.

Analysis of process parameters effects on underwater friction stir welding of aluminum alloy 6082-T6

2018 ◽  
Vol 233 (6) ◽  
pp. 1700-1710 ◽  
Author(s):  
Mohd Atif Wahid ◽  
Zahid A Khan ◽  
Arshad Noor Siddiquee ◽  
Rohit Shandley ◽  
Nidhi Sharma
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Underwater Friction Stir Welding ◽  
Optimal Setting

In friction stir welding of heat treatable aluminum alloys, the thermal cycles developed during the joining process result in softening of the joints which adversely affect their mechanical properties. Underwater friction stir welding can be a process of choice to overcome this problem due to low peak temperature and short dwell time involved during the process. Consequently, this article presents a study pertaining to the underwater friction stir welding of aluminum alloy 6082-T6 with an aim to develop a mathematical model to optimize the underwater friction stir welding process parameters for obtaining maximum tensile strength. The results of the study reveal that the tool shoulder diameter (d), tool rotational speed (ω), welding speed (v), and second-order term of rotational speed, that is, ω2, significantly affect the tensile strength of the joint. The maximum tensile strength of 241 MPa which is indeed 79% of the base metal strength and 10.7% higher than that of conventional (air) friction stir welding joint was achieved at an optimal setting of the underwater friction stir welding parameters, that is, tool rotational speed of 900 r/min, the welding speed of 80 mm/min, and a tool shoulder of 17 mm. The article also presents the results of temperature variation, the macrostructural and microstructural investigations, microhardness, and fractography of the joint obtained at the optimal setting for underwater friction stir welded (UFSWed) joint.

Effects of friction stir welding on corrosion and mechanical properties of AA6063 in sea water

2021 ◽  
pp. 095440622199554
Author(s):  
Laxmana Raju Salavaravu ◽  
Lingaraju Dumpala
Keyword(s):  
Mechanical Properties ◽  
Electron Microscope ◽  
Friction Stir Welding ◽  
Corrosion Rate ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Tool Pin

Submerged friction stir welding (FSW) is used to improve the weld zones mechanical properties in the present study. This research aims to obtain the optimized process parameters used to fabricate the AA6063 Submerged FSW joint. In the Submerged FSW process, the most important influential factors are tool rotational speed, traverse speed, and pin profile in a seawater environment. The different workpieces are friction stir welded while submerged in seawater at different tool rotational speeds, traverse speeds, and tool pin profiles such as square pin, cylindrical taper pin, and threaded pin. The produced weldments were tested for the mechanical properties of higher tensile strength, microhardness, corrosion rate, and the microstructure of weldments was characterized by using a scanning electron microscope, transmission electron microscope, and X-ray diffractometer. The corrosion rate is investigated by using an electrochemical analyzer by potential dynamic polarization open-circuit technique. For this investigation, The Taguchi method with the L9 orthogonal array design of experimentation is adopted. The maximum UTS was acquired in the weld joint fabricated with 1250 r/min of tool rotational speed, 45 mm/min traverse speed, and a square tool pin. The stirred zone is tested for microhardness. High hardness is achieved with high tool rotational speed and low traverse speed with a square tool pin profile. The corrosion rate is also decreased with high tool rotational speed, low traverse speed, and a square tool pin profile.

scholarly journals Optimization of Process Parameters on Friction Stir Welding of AA 6082-T6 Butt Joints Using Taguchi Method

2020 ◽  
Vol 22 (4) ◽  
pp. 1371-1380
Author(s):  
Mustapha Arab ◽  
Mokhtar Zemri
Keyword(s):  
Friction Stir Welding ◽  
Taguchi Method ◽  
Process Parameters ◽  
Welding Speed ◽  
Rotational Speed ◽  
Optimum Process ◽  
Friction Stir ◽  
Optimum Parameters ◽  
Optimization Of Process Parameters ◽  
Two Factors

AbstractFriction Stir Welding (FSW) was carried out on Aluminum Alloy 6082-T6 plates with dimensions of 200 × 70 × 2 mm. Design of Experiment (DOE) was applied to determine the most important factors which influence the Ultimate Tensile Strength (UTS) and Hardness (HV) of AA 6082-T6 joints produced by Friction Stir Welding (FSW). Effect of two factors which include tool rotational speed and welding speed on (UTS, HV) were investigated by Taguchi method using L9 orthogonal array to find the optimum process parameters. An analysis of variance (ANOVA) was carried out to determine which of the selected factors are more significant on both of responses, the optimum parameters for the higher UTS it found by using a rotational speed of 1400 rpm and 125 mm/min for the welding speed, also 1400 rpm and 160 mm/min to maximize Hardness (HV).

Effect of Process Parameters on Mechanical Characterization of Dissimilar Friction Stir Welded Aluminium Alloys

2015 ◽  
Vol 766-767 ◽  
pp. 701-704
Author(s):  
R. Ramesh ◽  
S. Suresh Kumar ◽  
R.V. Srinivasan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Process Parameters ◽  
Weight Ratio ◽  
Welding Parameters ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Axial Forces ◽  
Tool Pin

Aluminum alloys exhibit poor weldability by conventional fusion welding process. The heat treatable aluminum alloy AA2014 is extensively used in the aircraft industry because it has good ductility and high strength to weight ratio. In this paper the effects of welding parameters and tool profile on the mechanical properties of friction stir welded butt joints of dissimilar aluminum alloy sheets AA6082 and AA2014. The process parameters such as rotational speed, transverse speed and axial forces were considered. The effect of parameters on weld quality was analyzed. Hardness and tensile tests are carried out at room temperature to examine the mechanical properties of the welded joints. The joints produced with straight square tool pin profile have higher ultimate tensile strength, whereas the straight cylindrical tool pin profile results in lower tensile strength.

scholarly journals Experimental Investigation of Friction stir Welding Using Hybrid Alloys

2021 ◽  
pp. 352-360
Author(s):  
A. J Amroliya ◽  
Dr. D. B Jani ◽  
Dr. R. K Shukla
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Rotational Speed ◽  
Research Work ◽  
Weld Strength ◽  
Tool Rotational Speed ◽  
Experimental Conditions ◽  
Friction Stir ◽  
Fsw Parameters ◽  
Tool Pin

Friction stir welding is an emerging solid state joining process which is used to join metals and alloys having low weldability. In this research work experimental analysis has been performed on FSW for AA 6061 and MgZ31B A. Effect of FSW parameters like tool rpm, tool transverse speed and tool pin profile are investigated. A vertical milling head is used to produce FSW joints. Hot work tool steel (H13) is used as a tool material and total 3 number of tools are manufactured namely as cylindrical pin, tapered pin and square pin. Tool transverse feed of 10, 15 and 20 mm/min and tool rotational speed of 800, 1000 and 1200 rpm are taken for the study. A full factorial method is used for three numbers of parameters and their three levels and total 27 numbers of experiments are conducted keeping all other parameters constant. As a response weld tensile strength of joints are tested according to ASME-IX. Response surface method (RSM) and Analysis of variance (ANOVA) is adopted for the statistical analysis. Chi square method is used for the validation purpose and a strong match has been found between predicted and actual value of weld tensile strength of joints. As a conclusion it has been derived that feed of 15 mm/min, tool rotational speed of 1200 rpm and tapered pin profile gives better weld strength for the given experimental conditions. Furthermore research can be carried out on Bobbin type tool, numerical analysis and multi pass of FSW tool.

Sign in / Sign up

Export Citation Format

Share Document