Effects of friction stir welding on corrosion and mechanical properties of AA6063 in sea water

2021 ◽  
pp. 095440622199554
Author(s):  
Laxmana Raju Salavaravu ◽  
Lingaraju Dumpala
Keyword(s):  
Mechanical Properties ◽  
Electron Microscope ◽  
Friction Stir Welding ◽  
Corrosion Rate ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Tool Pin

Submerged friction stir welding (FSW) is used to improve the weld zones mechanical properties in the present study. This research aims to obtain the optimized process parameters used to fabricate the AA6063 Submerged FSW joint. In the Submerged FSW process, the most important influential factors are tool rotational speed, traverse speed, and pin profile in a seawater environment. The different workpieces are friction stir welded while submerged in seawater at different tool rotational speeds, traverse speeds, and tool pin profiles such as square pin, cylindrical taper pin, and threaded pin. The produced weldments were tested for the mechanical properties of higher tensile strength, microhardness, corrosion rate, and the microstructure of weldments was characterized by using a scanning electron microscope, transmission electron microscope, and X-ray diffractometer. The corrosion rate is investigated by using an electrochemical analyzer by potential dynamic polarization open-circuit technique. For this investigation, The Taguchi method with the L9 orthogonal array design of experimentation is adopted. The maximum UTS was acquired in the weld joint fabricated with 1250 r/min of tool rotational speed, 45 mm/min traverse speed, and a square tool pin. The stirred zone is tested for microhardness. High hardness is achieved with high tool rotational speed and low traverse speed with a square tool pin profile. The corrosion rate is also decreased with high tool rotational speed, low traverse speed, and a square tool pin profile.

scholarly journals Parametric Optimization of Mechanical Properties via FSW on AA5052 Using Taguchi Based Grey Relational Analysis

2021 ◽  
Vol 13 (2) ◽  
pp. 21-30
Author(s):  
C. CHANAKYAN ◽  
S. SIVASANKAR ◽  
M. MEIGNANAMOORTHY ◽  
S. V. ALAGARSAMY
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Grey Relational Analysis ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Relational Analysis ◽  
Grey Relational ◽  
Tool Pin

The Friction stir processing benefits of aluminium composites contain advanced exploration in the region of aluminium alloy Friction Stir Welding - FSW. The modern advancements in Friction Stir Welding are concentrated on the optimization of welding parameters for multi response attributes. The investigations were carried out with the tool pin profiles, tool rotational speed and traverse speed as predictable process parameters for multi response optimization in Friction Stir Welding of 5052 aluminium alloy. GRG (grey relational grade) was obtained by the grey relational analysis of the friction stir welding process through different qualities, particularly, UTS-ultimate tensile strength and micro hardness. The significant process variables on GRG and most substantial parameters traverse speed and tool pin profiles are examined by ANOVA. Excluding tool rotational speed, tool pin profiles and traverse speed were likewise observed to be significant. To approve the investigation, verification of tests was completed at optimal parameters arrangement and predicted outcomes were observed to be in great concurrence with test values.

Effect of Al2O3 nanoparticles on microstructure and mechanical properties of friction stir-welded dissimilar aluminum alloys AA7075-T6 and AA6061-T6

2021 ◽  
pp. 095440892110655
Author(s):  
Sumit Jain ◽  
R.S. Mishra
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Particle Dispersion ◽  
Al2o3 Nanoparticles ◽  
Tool Rotational Speed ◽  
Micro Hardness ◽  
Friction Stir ◽  
Dissimilar Aluminum Alloys

In this research, a defect-free dissimilar weld joint of AA7075-T6 and AA6061-T6 reinforced with Al2O3 nanoparticles was fabricated via friction stir welding (FSW). The influence of tool rotational speed (700, 900 and 1100 rpm), traverse speed (40, 50 and 60 mm/min) with varying volume fractions of Al2O3 nanoparticles (4%, 7% and 10%) on microstructural evolution and mechanical properties were investigated. The augmentation of various mechanical properties is based on the homogeneity of particle dispersion and grains refinement in the SZ of the FSWed joint. The findings revealed that the remarkable reduction in grain size in the SZ was observed owing to the incorporation of Al2O3 nanoparticles produces the pinning effect, which prevents the growth of grain boundaries by dynamic recrystallization (DRX). The increasing volume fraction of Al2O3 nanoparticles enhanced the mechanical properties such as tensile strength, % elongation and micro-hardness. Agglomeration of particles was observed in the SZ of the FSWed joints produced at lower tool rotational speed of 700 rpm and higher traverse speed of 60 mm/min due to unusual material flow. Homogenous particle dispersion and enhanced material mixing ensue at higher rotational speed of 1100 rpm and lower traverse speed of 40 mm/min exhibit higher tensile strength and micro-hardness.

Mechanical Property of Friction Stir Welded Retardant Magnesium Alloy Joint

2011 ◽  
Vol 295-297 ◽  
pp. 1929-1932
Author(s):  
Yi Min Tu ◽  
Ran Feng Qiu ◽  
Hong Xin Shi ◽  
Xin Zhang ◽  
Ke Ke Zhang
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Friction Stir Welding ◽  
Magnesium Alloy ◽  
Welding Speed ◽  
Rotational Speed ◽  
Maximum Strength ◽  
Welding Parameters ◽  
Tool Rotational Speed ◽  
Friction Stir

In order to obtain better understanding of the friction stir weldability of the magnesium alloy and provide some foundational information for improving mechanical properties of retardant magnesium alloy joints. A retardant magnesium alloy was weld using the method of friction stir welding. The influence of welding parameters on the strength of the joint was investigated. The maximum strength of 230 MPa was obtained from the joint welded at the tool rotational speed of 1000 r/min and welding speed of 750 mm/min.

Optimization of friction stir welding process parameters for AA6063-ETP copper using central composite design

2020 ◽  
Vol 17 (4) ◽  
pp. 491-507 ◽  
Author(s):  
Nitin Panaskar ◽  
Ravi Prakash Terkar
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Content Type ◽  
Friction Stir ◽  
Central Composite

Purpose Recently, several studies have been performed on lap welding of aluminum and copper using friction stir welding (FSW). The formation of intermetallic compounds at the weld interface hampers the weld quality. The use of an intermediate layer of a compatible material during welding reduces the formation of intermetallic compounds. The purpose of this paper is to optimize the FSW process parameters for AA6063-ETP copper weld, using a compatible zinc intermediate filler metal. Design/methodology/approach In the present study, a three-level, three-factor central composite design (CCD) has been used to determine the effect of various process parameters, namely, tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil on ultimate tensile strength of the weld. A total of 60 experimental data were fitted in the CCD. The experiments were performed with tool rotational speeds of 1,000, 1,200 and 1,400 rpm each of them with tool traverse speeds of 5, 10 and 15 mm/min. A zinc inter-filler foil of 0.2 and 0.4 mm was also used. The macrograph of the weld surface under different process parameters and the tensile strength of the weld have been investigated. Findings The feasibility of joining 3 mm thick AA6063-ETP copper using zinc inter-filler is established. The regression analysis showed a good fit of the experimental data to the second-order polynomial model with a coefficient of determination (R2) value of 0.9759 and model F-value of 240.33. A good agreement between the prediction model and experimental findings validates the reliability of the developed model. The tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil significantly affected the tensile strength of the weld. The optimal conditions found for the weld were, rotational speed of 1,212.83 rpm and traverse speed of 9.63 mm/min and zinc foil thickness is 0.157 mm; by using optimized values, ultimate tensile strength of 122.87 MPa was achieved, from the desirability function. Originality/value Aluminium and copper sheets could be joined feasibly using a zinc inter-filler. The maximum tensile strength of joints formed by inter-filler (122.87 MPa) was significantly better as compared to those without using inter-filler (83.78 MPa). The optimum process parameters to achieve maximum tensile strength were found by CCD.

Effect of Tool Rotational Speed on Microstructure and Microhardness of AA6082/TiC Surface Composites using Friction Stir Processing

2014 ◽  
Vol 592-594 ◽  
pp. 234-239 ◽  
Author(s):  
A. Thangarasu ◽  
N. Murugan ◽  
I. Dinaharan ◽  
S.J. Vijay
Keyword(s):  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Surface Composite ◽  
Surface Composites ◽  
Homogenous Distribution ◽  
Tool Pin ◽  
Scanning Electron

Friction stir processing (FSP) is as a novel modifying technique to synthesize surface composites. An attempt has been made to synthesis AA6082/TiC surface composite using FSP and to analyze the effect of tool rotational speed on microstructure and microhardness of the same. The tool rotational speed was varied from 800 rpm to 1600 rpm in steps of 400 rpm. The traverse speed, axial force, groove width and tool pin profile were kept constant. Scanning electron microscopy was employed to study the microstructure of the fabricated surface composites. The results indicated that the tool rotational speed significantly influenced the area of the surface composite and distribution of TiC particles. Higher rotational speed provided homogenous distribution of TiC particles while lower rotational speed caused poor distribution of TiC particles in the surface composite. The effect of the tool rotational speed on microhardness is also reported in this paper.

scholarly journals Influence of tool rotational speed on the evolution of microstructure and mechanical properties of precipitation-hardened Aluminium 6061 butt joint during friction stir welding

2022 ◽  
Author(s):  
Biplab Ghosh ◽  
Hrishikesh Das ◽  
Asis Samanta ◽  
Jyotsna Dutta Majumdar ◽  
Manojit Ghosh
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Rotational Speed ◽  
Butt Joint ◽  
Tool Rotational Speed ◽  
Nugget Zone ◽  
Friction Stir ◽  
Transmission Electron ◽  
Free Region ◽  
Evolution Of Microstructure

Abstract The present investigation intends to interpret the effect of tool rotational speed on the mechanical properties and microstructural evolution in Aluminium 6061-T6 alloy during friction stir welding. A higher value of tool rotation produces more hardness at the nugget zone, which is attributed to the higher intensity of reprecipitation at higher rpm, revealed by transmission electron microscopy. The nugget zone is revealed as a nearly precipitate-free region, while the thermo-mechanically affected zone contains coarse precipitates, deformed and dynamically recovered grains with a few recrystallized grains. Significant reduction in grain size in the stirred zone is also a key finding. The observations depict the dependence of microstructure, and thus mechanical behaviour on tool rotational speed. A specific combination of process parameters has been determined from experiments, which corresponds to the maximum joint efficiency.

Sign in / Sign up

Export Citation Format

Share Document