On finding of high piezoresistive response of carbon nanotube films without surfactants for in-plane strain detection

2011 ◽  
Vol 22 (18) ◽  
pp. 2155-2159 ◽  
Author(s):  
Y. Miao ◽  
L. Chen ◽  
Y. Lin ◽  
R. Sammynaiken ◽  
W. J. Zhang
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Plane Strain ◽  
Composite Films ◽  
Strain Sensors ◽  
Gauge Factor ◽  
Experimental Discovery ◽  
Strain Detection ◽  
Nanotube Films

The use of carbon nanotubes (CNTs) for construction of sensors is promising. This is due to some unique characteristics of CNTs. In recent years, strain sensors built from CNT composite films have been developed; however, their low piezoresistive sensitivity (gauge factor (GF)) in in-plane strain detection is a concern compared with other strain sensors. This article reports an experimental discovery of the superior piezoresistive response of a CNT film that is free of surfactants, known as the pure CNT film. The mechanism for the high GF with the pure CNT film strain sensors is also discussed.

scholarly journals A Review: Carbon Nanotube-Based Piezoresistive Strain Sensors

2012 ◽  
Vol 2012 ◽  
pp. 1-15 ◽  
Author(s):  
Waris Obitayo ◽  
Tao Liu
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Composite Films ◽  
Strain Sensors ◽  
Voltage Response ◽  
Strain Sensing ◽  
Multiwalled Carbon ◽  
Sensing Applications ◽  
Mechanical Deformations ◽  
Electrical Resistivities

The use of carbon nanotubes for piezoresistive strain sensors has acquired significant attention due to its unique electromechanical properties. In this comprehensive review paper, we discussed some important aspects of carbon nanotubes for strain sensing at both the nanoscale and macroscale. Carbon nanotubes undergo changes in their band structures when subjected to mechanical deformations. This phenomenon makes them applicable for strain sensing applications. This paper signifies the type of carbon nanotubes best suitable for piezoresistive strain sensors. The electrical resistivities of carbon nanotube thin film increase linearly with strain, making it an ideal material for a piezoresistive strain sensor. Carbon nanotube composite films, which are usually fabricated by mixing small amounts of single-walled or multiwalled carbon nanotubes with selected polymers, have shown promising characteristics of piezoresistive strain sensors. Studies also show that carbon nanotubes display a stable and predictable voltage response as a function of temperature.

scholarly journals Strain Sensor of Carbon Nanotubes in Microscale: From Model to Metrology

2014 ◽  
Vol 2014 ◽  
pp. 1-9
Author(s):  
Wei Qiu ◽  
Shi-Lei Li ◽  
Wei-lin Deng ◽  
Di Gao ◽  
Yi-Lan Kang
Keyword(s):  
Carbon Nanotubes ◽  
Raman Spectroscopy ◽  
Carbon Nanotube ◽  
Plane Strain ◽  
Standard Procedure ◽  
Strain Sensor ◽  
Mathematic Model ◽  
Strain Sensors ◽  
Polarization Control ◽  
Strain Components

A strain sensor composed of carbon nanotubes with Raman spectroscopy can achieve measurement of the three in-plane strain components in microscale. Based on previous work on the mathematic model of carbon nanotube strain sensors, this paper presents a detailed study on the optimization, diversification, and standardization of a CNT strain sensor from the viewpoint of metrology. A new miniaccessory for polarization control is designed, and two different preparing methods for CNT films as sensing media are introduced to provide diversified choices for applications. Then, the standard procedure of creating CNT strain sensors is proposed. Application experiments confirmed the effectiveness of the above improvement, which is helpful in developing this method for convenient metrology.

Ultra-stretchable and highly sensitive strain sensor based on gradient structure carbon nanotubes

Nanoscale ◽  
2018 ◽  
Vol 10 (28) ◽  
pp. 13599-13606 ◽  
Author(s):  
Binghao Liang ◽  
Zhiqiang Lin ◽  
Wenjun Chen ◽  
Zhongfu He ◽  
Jing Zhong ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Strain Sensor ◽  
High Sensitivity ◽  
Strain Sensors ◽  
Sensitive Strain ◽  
Gauge Factor ◽  
Gradient Structure ◽  
Highly Sensitive ◽  
Highly Stretchable

A highly stretchable and sensitive strain sensor based on a gradient carbon nanotube was developed. The strain sensors show an unprecedented combination of both high sensitivity (gauge factor = 13.5) and ultra-stretchability (>550%).

scholarly journals Synthesis of silver nanoparticles embedded with single-walled carbon nanotubes for printable elastic electrodes and sensors with high stability

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jae-Won Lee ◽  
Joon Young Cho ◽  
Mi Jeong Kim ◽  
Jung Hoon Kim ◽  
Jong Hwan Park ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Silver Nanoparticles ◽  
High Performance ◽  
Composite Films ◽  
Single Walled Carbon Nanotubes ◽  
Gauge Factor ◽  
Time Interval ◽  
Single Walled Carbon ◽  
Irradiation Energy ◽  
Walled Carbon Nanotubes

AbstractSoft electronic devices that are bendable and stretchable require stretchable electric or electronic components. Nanostructured conducting materials or soft conducting polymers are one of the most promising fillers to achieve high performance and durability. Here, we report silver nanoparticles (AgNPs) embedded with single-walled carbon nanotubes (SWCNTs) synthesized in aqueous solutions at room temperature, using NaBH4 as a reducing agent in the presence of highly oxidized SWCNTs as efficient nucleation agents. Elastic composite films composed of the AgNPs-embedded SWCNTs, Ag flake, and polydimethylsiloxane are irradiated with radiation from a Xenon flash lamp within a time interval of one second for efficient sintering of conductive fillers. Under high irradiation energy, the stretchable electrodes are created with a maximum conductivity of 4,907 S cm−1 and a highly stretchable stability of over 10,000 cycles under a 20% strain. Moreover, under a low irradiation energy, strain sensors with a gauge factor of 76 under a 20% strain and 5.4 under a 5% strain are fabricated. For practical demonstration, the fabricated stretchable electrode and strain sensor are attached to a human finger for detecting the motions of the finger.

Mechanical Properties Of Polyaniline / Multi-walled Carbon Nanotube Composite Films

2003 ◽  
Vol 791 ◽  
Author(s):  
P. C. Ramamurthy ◽  
W. R. Harrell ◽  
R. V. Gregory ◽  
B. Sadanadan ◽  
A. M. Rao
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Composite Films ◽  
Weight Percent ◽  
Organic Electronic Devices ◽  
Multiwalled Carbon ◽  
Multi Walled Carbon Nanotube ◽  
Contact Devices ◽  
Carbon Nanotube Composite

ABSTRACTHigh molecular weight polyaniline / multi-walled carbon nanotube composite films were fabricated using solution processing. Composite films with various weight percentages of multiwalled carbon nanotubes were fabricated. Physical properties of these composites were analyzed by thermogravimetric analysis, tensile testing, and scanning electron microscopy. These results indicate that the addition of multiwalled nanotubes to polyaniline significantly enhances the mechanical properties of the films. In addition, metal–semiconductor (composite) (MS) contact devices were fabricated, and it was observed that the current level in the films increased with increasing multiwalled nanotube content. Furthermore, it was observed that polyaniline containing one weight percent of carbon nanotubes appears to be the most promising composition for applications in organic electronic devices.

The Effect of Nanotube Loading and Dispersion on the Three-Dimensional Nanostructure of Carbon Nanotube-Conducting Polymer Composite Films

2002 ◽  
Vol 739 ◽  
Author(s):  
Mark Hughes ◽  
George Z. Chen ◽  
Milo S. P. Shaffer ◽  
Derek J. Fray ◽  
Alan H. Windle
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Conducting Polymer ◽  
Polymer Composite ◽  
Electrochemical Polymerization ◽  
Composite Films ◽  
Three Dimensional ◽  
Ionic Diffusion ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

ABSTRACTNanoporous composite films of multi-walled carbon nanotubes (MWNTs) and either polypyrrole (PPy) or poly(3-methylthiophene) (P3MeT) were grown using an electrochemical polymerization technique in which the nanotubes and conducting polymer were deposited simultaneously. The concentration and dispersion of MWNTs in the polymerization electrolyte was found to have a significant effect on the thickness of polymer coated on each MWNT and hence the loading of MWNTs in the films produced. It has been shown that for an increasing concentration of MWNTs in the polymerization electrolyte, the thickness of polymer coated on each MWNT decreases. This relationship made it possible to minimize ionic diffusion distances within the nanoporous MWNT-PPy films produced, reducing their electrical and ionic resistance and increasing their capacitance relative to similarly prepared pure PPy films.

Flexible resistance-type strain sensors toward monitoring finger movements

Synlett ◽  
2021 ◽  
Author(s):  
Chao Lu ◽  
Xi Chen
Keyword(s):  
Carbon Nanotubes ◽  
Electrical Properties ◽  
Composite Films ◽  
Strain Sensors ◽  
Sensitive Strain ◽  
Nanocomposite Films ◽  
Finger Movements ◽  
Resistance Response ◽  
Mechanical And Electrical Properties ◽  
Highly Sensitive

Flexible strain sensors with superior flexibility and high sensitivity are critical to artificial intelligence. And it is favorable to develop highly sensitive strain sensors with simple and cost effective method. Here, we have prepared carbon nanotubes enhanced thermal polyurethane nanocomposites with good mechanical and electrical properties for fabrication of highly sensitive strain sensors. The nanomaterials have been prepared through simple but effective solvent evaporation method, and the cheap polyurethane has been utilized as main raw materials. Only a small quantity of carbon nanotubes with mass content of 5% has been doped into polyurethane matrix with purpose of enhancing mechanical and electrical properties of the nanocomposites. As a result, the flexible nanocomposite films present highly sensitive resistance response under external strain stimulus. The strain sensors based on these flexible composite films deliver excellent sensitivity and conformality under mechanical conditions, and detect finger movements precisely under different bending angles.

scholarly journals An ultra-compact blackbody using electrophoretic deposited carbon nanotube films

RSC Advances ◽  
2018 ◽  
Vol 8 (7) ◽  
pp. 3453-3461 ◽  
Author(s):  
Albert Lin ◽  
Chien-Chih Yang ◽  
Parag Parashar ◽  
Chien-Yung Lin ◽  
Ding Rung Jian ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Optical Properties ◽  
Carbon Nanotube ◽  
Low Cost ◽  
Black Body ◽  
Compact Dimension ◽  
Nanotube Films

Electrophoretic-deposited carbon nanotubes (EPD-CNTs) possess decent optical properties and low-cost processing and thus can be used as an ideal black body with compact dimension.

scholarly journals A Fully Inkjet-Printed Strain Sensor Based on Carbon Nanotubes

Coatings ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 792 ◽  
Author(s):  
Hsuan-Ling Kao ◽  
Cheng-Lin Cho ◽  
Li-Chun Chang ◽  
Chun-Bing Chen ◽  
Wen-Hung Chung ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Surface Morphology ◽  
Silver Film ◽  
Strain Sensor ◽  
Strain Sensors ◽  
Gauge Factor ◽  
Lower Sensitivity ◽  
High Reproducibility ◽  
Silver Films ◽  
Microcrack Detection

A fully inkjet-printed strain sensor based on carbon nanotubes (CNTs) was fabricated in this study for microstrain and microcrack detection. Carbon nanotubes and silver films were used as the sensing layer and conductive layer, respectively. Inkjet-printed CNTs easily undergo agglomeration due to van der Waals forces between CNTs, resulting in uneven films. The uniformity of CNT film affects the electrical and mechanical properties. Multi-pass printing and pattern rotation provided precise quantities of sensing materials, enabling the realization of uniform CNT films and stable resistance. Three strain sensors printed eight-layer CNT film by unidirectional printing, rotated by 180° and 90° were compared. The low density on one side of eight-layer CNT film by unidirectional printing results in more disconnection and poor connectivity with the silver film, thereby, significantly increasing the resistance. For 180° rotation eight-layer strain sensors, lower sensitivity and smaller measured range were found because strain was applied to the uneven CNT film resulting in non-uniform strain distribution. Lower resistance and better strain sensitivity was obtained for eight-layer strain sensor with 90° rotation because of uniform film. Given the uniform surface morphology and saturated sheet resistance of the 20-layer CNT film, the strain performance of the 20-layer CNT strain sensor was also examined. Excluding the permanent destruction of the first strain, 0.76% and 1.05% responses were obtained for the 8- and 20-layer strain sensors under strain between 0% and 3128 µε, respectively, which demonstrates the high reproducibility and recoverability of the sensor. The gauge factor (GF) of 20-layer strain sensor was found to be 2.77 under strain from 71 to 3128 µε, which is higher than eight-layer strain sensor (GF = 1.93) due to the uniform surface morphology and stable resistance. The strain sensors exhibited a highly linear and reversible behavior under strain of 71 to 3128 µε, so that the microstrain level could be clearly distinguished. The technology of the fully inkjet-printed CNT-based microstrain sensor provides high reproducibility, stability, and rapid hardness detection.

scholarly journals Directed self-assembly of rhombic carbon nanotube nanomesh films for transparent and stretchable electrodes

2015 ◽  
Vol 3 (10) ◽  
pp. 2319-2325 ◽  
Author(s):  
Sehee Ahn ◽  
Ayoung Choe ◽  
Jonghwa Park ◽  
Heesuk Kim ◽  
Jeong Gon Son ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Sheet Resistance ◽  
Self Assembly ◽  
Lower Sheet ◽  
Mechanical Durability ◽  
Lower Sheet Resistance ◽  
Nanotube Films

Directed self-assembly of carbon nanotubes into 2D rhombic nanomesh films results in greatly lower sheet resistance, higher stretchability, and better mechanical durability than those of random carbon nanotube films.

Sign in / Sign up

Export Citation Format

Share Document