Wear analysis of an automotive window regulator slider

2019 ◽  
Vol 233 (10) ◽  
pp. 1508-1522 ◽  
Author(s):  
Xiaoshuang Xiong ◽  
Lin Hua ◽  
Xiaojin Wan ◽  
Wei Guo ◽  
Can Yang ◽  
...  
Keyword(s):  
Finite Element ◽  
Contact Pressure ◽  
Wear Test ◽  
Wear Depth ◽  
Wear Properties ◽  
Grease Lubrication ◽  
Element Analysis ◽  
Wear Life ◽  
Window Regulator ◽  
Lubrication Condition

The slider, which is made of polyoxymethylene, is the key component of an automotive window regulator. Its function is to guide the window's movement, but it is prone to wear and tear. To reduce noise and improve the wear life of slider, a study of its contact characteristic and the wear life is significant. In this paper, the wear and friction properties of polyoxymethylene under dry sliding condition and grease lubrication condition are investigated using a pin-on-disc apparatus. The complex force conditions of the slider at the normal working condition are studied by a mechanics analysis method. The contact pressure of slider is analyzed by the finite element analysis and the wear of slider is calculated by the proposed wear prediction model. Prediction of the wear life of slider is verified by a window regulator wear experiment. Results show that the value of wear rate of polyoxymethylene under unlubricated condition is much higher than that under lubricated condition. The estimation of wear depth of slider, based on the combination of finite element contact pressure analysis and wear properties of polyoxymethylene, is in accordance with window regulator wear test under unlubricated condition. Besides, the practical wear depth of slider under grease lubrication condition is also in the range of the predicted wear depth of slider under dry and grease lubrication condition.

Finite Element Analysis of Tire/Rim Interface Forces Under Braking and Cornering Loads

1992 ◽  
Vol 20 (2) ◽  
pp. 83-105 ◽  
Author(s):  
J. P. Jeusette ◽  
M. Theves
Keyword(s):  
Finite Element ◽  
Shear Stress ◽  
Contact Pressure ◽  
Element Model ◽  
Shear Stresses ◽  
Detailed Knowledge ◽  
Stress Distributions ◽  
Element Analysis ◽  
Plane Shear ◽  
Normal Contact

Abstract During vehicle braking and cornering, the tire's footprint region may see high normal contact pressures and in-plane shear stresses. The corresponding resultant forces and moments are transferred to the wheel. The optimal design of the tire bead area and the wheel requires a detailed knowledge of the contact pressure and shear stress distributions at the tire/rim interface. In this study, the forces and moments obtained from the simulation of a vehicle in stationary braking/cornering conditions are applied to a quasi-static braking/cornering tire finite element model. Detailed contact pressure and shear stress distributions at the tire/rim interface are computed for heavy braking and cornering maneuvers.

scholarly journals Effect of coronal plane acetabular correction on joint contact pressure in Periacetabular osteotomy: a finite-element analysis

2022 ◽  
Vol 23 (1) ◽  
Author(s):  
Kenji Kitamura ◽  
Masanori Fujii ◽  
Miho Iwamoto ◽  
Satoshi Ikemura ◽  
Satoshi Hamai ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Contact Pressure ◽  
Periacetabular Osteotomy ◽  
Anterior Wall ◽  
Coronal Plane ◽  
Patient Specific ◽  
Element Analysis ◽  
Joint Contact ◽  
Joint Contact Pressure

Abstract Background The ideal acetabular position for optimizing hip joint biomechanics in periacetabular osteotomy (PAO) remains unclear. We aimed to determine the relationship between acetabular correction in the coronal plane and joint contact pressure (CP) and identify morphological factors associated with residual abnormal CP after correction. Methods Using CT images from 44 patients with hip dysplasia, we performed three patterns of virtual PAOs on patient-specific 3D hip models; the acetabulum was rotated laterally to the lateral center-edge angles (LCEA) of 30°, 35°, and 40°. Finite-element analysis was used to calculate the CP of the acetabular cartilage during a single-leg stance. Results Coronal correction to the LCEA of 30° decreased the median maximum CP 0.5-fold compared to preoperatively (p <  0.001). Additional correction to the LCEA of 40° further decreased CP in 15 hips (34%) but conversely increased CP in 29 hips (66%). The increase in CP was associated with greater preoperative extrusion index (p = 0.030) and roundness index (p = 0.038). Overall, virtual PAO failed to normalize CP in 11 hips (25%), and a small anterior wall index (p = 0.049) and a large roundness index (p = 0.003) were associated with residual abnormal CP. Conclusions The degree of acetabular correction in the coronal plane where CP is minimized varied among patients. Coronal plane correction alone failed to normalize CP in 25% of patients in this study. In patients with an anterior acetabular deficiency (anterior wall index < 0.21) and an aspherical femoral head (roundness index > 53.2%), coronal plane correction alone may not normalize CP. Further studies are needed to clarify the effectiveness of multiplanar correction, including in the sagittal and axial planes, in optimizing the hip joint’s contact mechanics.

scholarly journals Finite element analysis to assess the biomechanical behavior of a finger model gripping handles with different diameters

2019 ◽  
Vol 11 (1) ◽  
pp. 69-79 ◽  
Author(s):  
Benedict Jain A.R. Tony ◽  
Masilamany S. Alphin
Keyword(s):  
Finite Element ◽  
Contact Pressure ◽  
Subcutaneous Tissue ◽  
Fe Model ◽  
Stress Strain ◽  
Element Analysis ◽  
Biomechanical Behavior ◽  
Biomechanical Response ◽  
Human Finger ◽  
Finger Model

SummaryStudy aim: Interactions between the fingers and a handle can be analyzed using a finite element finger model. Hence, the biomechanical response of a hybrid human finger model during contact with varying diameter cylindrical handles was investigated numerically in the present study using ABAQUS/CAE.Materials and methods: The finite element index finger model consists of three segments: the proximal, middle, and distal phalanges. The finger model comprises skin, bone, subcutaneous tissue and nail. The skin and subcutaneous tissues were assumed to be non-linearly elastic and linearly visco-elastic. The FE model was applied to predict the contact interaction between the fingers and a handle with 10 N, 20 N, 40 N and 50 N grip forces for four different diameter handles (30 mm, 40 mm, 44mm and 50 mm). The model predictions projected the biomechanical response of the finger during the static gripping analysis with 200 incremental steps.Results: The simulation results showed that the increase in contact area reduced the maximal compressive stress/strain and also the contact pressure on finger skin. It was hypothesized in this study that the diameter of the handle influences the stress/strain and contact pressure within the soft tissue during the contact interactions.Conclusions: The present study may be useful to study the behavior of the finger model under the static gripping of hand-held power tools.

Elastic-Plastic Finite Element Analysis of Indented Layered Media

1989 ◽  
Vol 111 (3) ◽  
pp. 430-439 ◽  
Author(s):  
K. Komvopoulos
Keyword(s):  
Finite Element ◽  
Plastic Zone ◽  
Contact Pressure ◽  
Critical Parameters ◽  
The Finite Element Method ◽  
Contact Pressure Distribution ◽  
Element Analysis ◽  
Elastic Plastic ◽  
Substrate Properties ◽  
Layered Half Space

The elastic-plastic contact problem of a layered half-space indented by a rigid surface is solved with the finite element method. The case of a layer stiffer and harder than the substrate is analyzed and solutions for the contact pressure, subsurface stresses and strains, and location, shape, and growth of the plastic zone are presented for various layer thicknesses and indentation depths. Finite element results for a halfspace having the substrate properties are also given for comparison purposes. Differences between the elastic and elastic-plastic solutions are discussed and the significance of critical parameters such as the layer thickness, mechanical properties of layer and substrate materials, indentation depth, and interfacial friction on the threshold of plasticity, contact pressure distribution, and growth of the plastic zone are examined. Additionally, the mechanisms of layer decohesion and subsurface crack initiation are interpreted in light of the results obtained in this study.

Evaluation of the Elliptical Flange Configurations for 24-Inch and 30-Inch Heater/Cooler Units

2007 ◽  
Author(s):  
Chris Alexander ◽  
Wade Armer ◽  
Stuart Harbert
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Heat Exchanger ◽  
Contact Pressure ◽  
Parameter Study ◽  
Element Analysis ◽  
Iterative Design ◽  
Pressure Changes ◽  
Geometric Changes ◽  
Maximum Contact

KOCH Heat Transfer Company contracted Stress Engineering Services, Inc. to perform a design/parameter study of a return bonnet used in hairpin heat exchangers that employs an elliptical flange design. The return bonnet is an important component of the heat exchanger as it can be removed to permit inspection of the heat exchanger tubes. The return bonnet is bolted to the hairpin leg flange. To maintain sealing integrity a gasket is placed between the return bonnet flange and the hairpin leg flange. The sealing efficiency of two return bonnet sizes (24-inch and 30-inch) was investigated in this study using finite element analysis. The sealing efficiency is an indication of how the contact pressure changes circumferentially around the gasket and is calculated by dividing the local contact pressure by the maximum contact pressure calculated in the gasket for each respective design. The study assessed the effects of geometric changes to the mating flanges. Using an iterative design process using finite element analysis, the elliptical flanges were optimized to maximize sealing efficiency. Upon completion of the study, the manufacturer successfully employed the modifications as evidenced with multiple successful hydrotests.

Combined Effects of Tube Projection, Initial Tube-Tubesheet Clearance, and Tube Material Strain Hardening on Rolled Joint Strength

2009 ◽  
Vol 131 (5) ◽  
Author(s):  
N. Merah ◽  
A. Al-Aboodi ◽  
A. N. Shuaib ◽  
Y. Al-Nassar ◽  
S. S. Al-Anizi
Keyword(s):  
Finite Element ◽  
Strain Hardening ◽  
Contact Pressure ◽  
Joint Strength ◽  
Element Model ◽  
Design Parameters ◽  
Radial Clearance ◽  
Tube Material ◽  
Element Analysis ◽  
Interfacial Pressure

The tube-to-tubesheet joint strength is measured in terms of interfacial pressure between the tube’s outer surface and tubesheet bore. The strength of a rolled joint is influenced by several design parameters, including the type of tube and tubesheet materials, initial tube projection, and the initial radial clearance between the tube and tubesheet, among other factors. This paper uses finite element analysis (FEA) to evaluate the effect of several parameters on the strength of rolled joints having large overtolerances, a situation that applies to used equipment. An axisymmetric finite element model based on the sleeve diameter and rigid tube expanding roller concepts was used to analyze the effects of tube projection, initial tube-tubesheet clearance, and tube material strain-hardening property on the deformation behavior of the rolled tube and on the strength of the tube-tubesheet joint. The FEA results show that for zero tube projection (flush) the initial clearance effect is dependent on the strain-hardening capability of the tube material. For low strain-hardening tube material the interfacial pressure remains constant well above the Tubular Exchanger Manufacturer’s Association maximum overtolerance. A drastic reduction in joint strength is observed at high values of radial clearances. The cut-off clearance (clearance at which the interfacial pressure starts to drop) is found to vary linearly with the tube material hardening level, and the contact stress increases slightly for moderate strain-hardening tube materials but shows lower cut-off clearance levels. Furthermore, with flush tubes the maximum contact pressure occurs close to the secondary face (at the end of rolling) while for joints with initial tube projection the contact pressure shows two maxima occurring near the primary and the secondary faces. This is attributed to the presence of two elbows in tube deformation near the primary and secondary faces. The average interfacial pressure increased with increasing projection length for all clearances. Tube material strain hardening enhances the interfacial pressure in a similar fashion for all initial tube projection lengths considered in the analysis.

Sign in / Sign up

Export Citation Format

Share Document