Seismic design of hybrid unbonded post-tensioned precast concrete joints based on bearing capacity and energy dissipation capacity

2020 ◽  
pp. 136943322098273
Author(s):  
Baoxi Song ◽  
Weizhi Xu ◽  
Dongsheng Du ◽  
Shuguang Wang ◽  
Weiwei Li ◽  
...  
Keyword(s):  
Energy Dissipation ◽  
Bearing Capacity ◽  
Design Method ◽  
Precast Concrete ◽  
Residual Deformation ◽  
Time History ◽  
Frame Structure ◽  
Energy Dissipation Capacity ◽  
Concrete Joints ◽  
Post Tensioned

This paper provides a practical design method for hybrid unbonded post-tensioned precast concrete joints. Such joints featured with self-centering capacities have been widely favored in recent years. However, the absence of design methods hinders their further promotion. To solve the issue, two methods for calculating mechanical behavior of the joints were first studied: characteristic points method and iterative method. The effectiveness of the methods was verified by the existing test results. On this basis, a joint design method considering both yield bearing capacity and energy dissipation capacity was proposed. Moreover, to facilitate design, some factors affecting the bearing capacity were discussed. A five-story frame structure was designed by the proposed design method, and the influence of two design factors on structural response was analyzed by utilizing nonlinear time-history method. The analysis results show that: with the increase of energy dissipation factor αs, the post-earthquake residual deformation of the structure tends to increase linearly, while the accumulated damage of the structure will decrease continuously; both overdesign and underdesign of bearing capacity of the joint are unfavorable; and near-field earthquake may cause irreparable damage to structural columns, making the residual deformation of structures contrary to the self-centering capacity of joints, which shall be considered during engineering design.

scholarly journals Parametric Study on Self-centering Precast Concrete Frames with Hysteretic Dampers

2021 ◽  
Author(s):  
Yadong Li ◽  
Fangfang Geng ◽  
Youliang Ding ◽  
Libin Wang
Keyword(s):  
Energy Dissipation ◽  
Rational Design ◽  
Modular Design ◽  
Precast Concrete ◽  
Time History ◽  
Bending Moment ◽  
Frame Structure ◽  
Concrete Frame ◽  
Energy Dissipation Capacity ◽  
Hysteretic Dampers

The self-centering precast concrete frame structure combines the advantages of industrialization and low earthquake damage, and its energy dissipation capacity and seismic performance have always been the focus of research. This paper proposed a kind of self-centering precast concrete frame with hysteretic dampers (SCPCHD). Its modular design makes the energy dissipation device and components easy to repair and replace. In order to obtain the optimal design, the finite element models of SCPCHD frames with different layout types of post-tensioned (PT) tendons and different shapes of hysteretic dampers are established, and the elastoplastic dynamic time-history analyses are carried out. The results show that the layout types and vertical margin of PT tendons have little effect on the displacement response of the frame structure. Compared to linear PT tendons, polygonal PT tendons can better bear the bending moment of the beam and reduce the stress of longitudinal reinforcements in the beam. The reduce effect of shortening the vertical margin on the tensile damage of beam concrete is obvious in the frame with polygonal PT tendons, but not obvious in the frame with linear PT tendons. Rational design of the prestressing force also plays a crucial role in the energy dissipation capacity of SCPCHD frames.

scholarly journals Experimental Study of a New Precast Prestressed Concrete Joint

2018 ◽  
Vol 8 (10) ◽  
pp. 1871 ◽  
Author(s):  
Xueyuan Yan ◽  
Suguo Wang ◽  
Canling Huang ◽  
Ai Qi ◽  
Chao Hong
Keyword(s):  
Energy Dissipation ◽  
Seismic Performance ◽  
Prestressed Concrete ◽  
Precast Concrete ◽  
Concrete Strength ◽  
Frame Structure ◽  
Loading Test ◽  
Concrete Frame ◽  
Concrete Joints ◽  
Precast Prestressed Concrete

Precast monolithic structures are increasingly applied in construction. Such a structure has a performance somewhere between that of a pure precast structure and that of a cast-in-place structure. A precast concrete frame structure is one of the most common prefabricated structural systems. The post-pouring joint is important for controlling the seismic performance of the entire precast monolithic frame structure. This paper investigated the joints of a precast prestressed concrete frame structure. A reversed cyclic loading test was carried out on two precast prestressed concrete beam–column joints that were fabricated with two different concrete strengths in the keyway area. This testing was also performed on a cast-in-place reinforced concrete joint for comparison. The phenomena such as joint crack development, yielding, and ultimate damage were observed, and the seismic performance of the proposed precast prestressed concrete joint was determined. The results showed that the precast prestressed concrete joint and the cast-in-place joint had a similar failure mode. The stiffness, bearing capacity, ductility, and energy dissipation were comparable. The hysteresis curves were full and showed that the joints had good energy dissipation. The presence of prestressing tendons limited the development of cracks in the precast beams. The concrete strength of the keyway area had little effect on the seismic performance of the precast prestressed concrete joints. The precast prestressed concrete joints had a seismic performance that was comparable to the equivalent monolithic system.

Experimental Investigations on the Seismic Behavior of Precast Concrete Columns with Novel Box Connections

2019 ◽  
Vol 14 (02) ◽  
pp. 2050007
Author(s):  
Xizhi Zhang ◽  
Shengbo Xu ◽  
Shaohua Zhang ◽  
Gaodong Xu
Keyword(s):  
Energy Dissipation ◽  
Bearing Capacity ◽  
Failure Mode ◽  
Seismic Behavior ◽  
Load Transfer ◽  
Precast Concrete ◽  
Hysteretic Behavior ◽  
Experimental Investigations ◽  
Test Results ◽  
Energy Dissipation Capacity

In this study, two types of novel box connections were developed to connect precast concrete (PC) columns and to ensure load transfer integrity. Cyclic loading tests were conducted to investigate the seismic behavior of the PC columns with proposed connections as well as the feasibility and reliability of novel box connections. The failure mode, hysteretic behavior, bearing capacity, ductility, stiffness degradation and energy dissipation were obtained and discussed. The test results indicated that the all PC columns exhibited the ductile flexural failure mode and that the proposed connections could transfer the force effectively. The adoption of novel box connections could improve the deformation capacity and energy dissipation capacity of PC columns. A higher axial compression ratio could enhance the bearing capacity of PC column with proposed connection but would significantly deteriorate the ductility and energy dissipation capacity. Finite element models were developed and the feasibility of the models was verified by the comparison with the test results.

ENERGY DISSIPATION IN POST-TENSIONED SELF-CENTERING PRECAST CONCRETE CONNECTIONS WITH A FRICTION DEVICE

2015 ◽  
Vol 2 (1) ◽  
Author(s):  
Takeaki Koshikawa
Keyword(s):  
Energy Dissipation ◽  
Friction Force ◽  
Precast Concrete ◽  
Design Parameters ◽  
Effective Energy ◽  
Energy Dissipation Capacity ◽  
Post Tensioning ◽  
The Moment ◽  
The Relationship ◽  
Post Tensioned

This paper presents an analytical study on the energy dissipation capacity of unbonded post-tensioned self-centering precast concrete beam-column connections that have a friction device only below the beam or on the web. The energy dissipation capacity is quantified using an effective energy dissipation ratio. To quantitatively evaluate the influence of three design parameters on the energy dissipation capacity, nonlinear analyses were carried out using a section-analysis method to predict the relationship between the moment and the relative rotation at the beam-column interface under cyclic loading. The design parameters were the initial post-tensioning force in the unbonded post-tensioning tendon, the friction force, and the location of the friction device. The analysis results show that the effective energy dissipation ratios for connections whose friction devices are in the same location can be related to the ratio of the friction force to the initial post-tensioning force.

A Practical Design Method for Energy Dissipation Structure

2012 ◽  
Vol 204-208 ◽  
pp. 1150-1153
Author(s):  
Min Chen ◽  
Guo Jing He ◽  
Chang Liu
Keyword(s):  
Energy Dissipation ◽  
Design Method ◽  
Damping Ratio ◽  
Time History ◽  
Structure Design ◽  
Frame Structure ◽  
Seismic Region ◽  
History Analysis ◽  
Dissipation Structure ◽  
Supplemental Damping

Energy dissipation structure is favored by designers because the earthquake energy can be dissipated by the dampers, which can avoid or reduce the damage caused by earthquake. However, the energy dissipation structure design is complex and the most domestic designers can not master it easily. In this paper, a simple and practicable design method for viscous damper dissipation structure by using the PKPM design software is proposed based on a 7-storey frame structure in highly seismic region. Firstly, lower half or one degree for the design intensity to design out an uncontrolled structure. Secondly, determine the supplemental damping ratio required for the fortification intensity via modal analysis method of PKPM software, and identify the numbers of the required dampers as well as their corresponding installation positions in line with the methods in the seismic code of China. Finally, the ETABS program is adopted to conduct the time-history analysis of the designed dissipation structure, showing that the proposed method in this paper can produce a satisfied result.

scholarly journals Influence of Different Types of Infill Walls on the Hysteretic Performance of Reinforced Concrete Frames

Buildings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 310
Author(s):  
Fei Wang ◽  
Kaozhong Zhao ◽  
Jianwei Zhang ◽  
Kai Yan
Keyword(s):  
Reinforced Concrete ◽  
Energy Dissipation ◽  
Bearing Capacity ◽  
Frame Structure ◽  
Concrete Frames ◽  
Reinforced Concrete Frame ◽  
Infill Walls ◽  
Concrete Frame ◽  
Hysteretic Performance ◽  
Energy Dissipation Capacity

To study the influence of masonry infill walls on the hysteretic performance of reinforced concrete frames, a cyclic experiment was conducted for three two-story and two-span reinforced concrete frame structures, including one reinforced concrete frame without infill walls and two frames with infill walls. Whether the infill walls were constructed in the frames and the type of infilled material were the main parameters of the test. The major results reveal that: the infill walls clearly changed the mechanical mechanism of the frame structure at the early stage of loading, magnified the stiffness and horizontal bearing capacity of the frame structure, and enhanced the energy dissipation capacity of the frame structure, but reduced the deformation performance of the frame structure. In the later stage of loading, the infill walls would no longer work as one with the frame gradually with the failure of the infill walls, and the above performance of the structure would approach the empty frame structure. Moreover, the initial stiffness, energy dissipation capacity, and horizontal bearing capacity of the frame with infill walls of clay hollow bricks were the highest among the three specimens. But due to the strong diagonal bracing effect, the damage to the top of the columns and beam-column joints was serious, the yield displacement was reduced significantly, and the shear failure of the top of the columns and the joints occurred prematurely, which showed poor performance of deformation and ductility. However, the frame with infill walls of relatively soft aerated lightweight concrete blocks showed better performance of deformation and ductility.

scholarly journals Seismic Performance Assessments of RC Frame Structures Strengthened by External Precast Wall Panel

2020 ◽  
Vol 10 (5) ◽  
pp. 1749
Author(s):  
Seung-Ho Choi ◽  
Jin-Ha Hwang ◽  
Sun-Jin Han ◽  
Hyo-Eun Joo ◽  
Hyun-Do Yun ◽  
...  
Keyword(s):  
Energy Dissipation ◽  
Seismic Performance ◽  
Precast Concrete ◽  
Frame Structure ◽  
Frame Structures ◽  
Rc Frame ◽  
Analysis Model ◽  
Energy Dissipation Capacity ◽  
Precast Walls ◽  
Rc Frame Structures

In recent years, a variety of strengthening methods have been developed to improve the seismic performance of reinforced concrete (RC) frame structures with non-seismic details. In this regard, this study proposes a new type of seismic strengthening method that compresses prefabricated precast concrete (PC) walls from the outside of a building. In order to verify the proposed method, a RC frame structure strengthened with precast walls was fabricated, and cyclic loading tests were performed. The results showed that specimens strengthened using the proposed method exhibited further improvements in strength, stiffness and energy dissipation capacity, compared to RC frame structures with non-seismic details. In addition, a nonlinear analysis method, capable of considering the flexural compression and shear behaviors of the walls, was suggested to analytically evaluate the structural behavior of the frame structures strengthened by the proposed method. Using this, an analysis model for frame structures strengthened with precast walls was proposed. Through the proposed model, the analysis and test results were compared in relation to stiffness, strength, and energy dissipation capacity. Then, the failure mode of the column was evaluated based on the pushover analysis. In addition, this study proposed a simplified analysis model that considered the placement of longitudinal reinforcements in shear walls.

scholarly journals Seismic Response and Evaluation of SDOF Self-Centering Friction Damping Braces Subjected to Several Earthquake Ground Motions

2015 ◽  
Vol 2015 ◽  
pp. 1-17 ◽  
Author(s):  
Jong Wan Hu ◽  
Myung-Hyun Noh
Keyword(s):  
Energy Dissipation ◽  
Seismic Response ◽  
Ground Motions ◽  
Residual Deformation ◽  
Time History ◽  
Frame Structure ◽  
Friction Damping ◽  
Friction Mechanism ◽  
Earthquake Ground Motions ◽  
Concentrically Braced Frame

This paper mainly deals with seismic response and performance for self-centering friction damping braces (SFDBs) subjected to several maximum- or design-leveled earthquake ground motions. The self-centering friction damping brace members consist of core recentering components fabricated with superelastic shape memory alloy wires and energy dissipation devices achieved through shear friction mechanism. As compared to the conventional brace members for use in the steel concentrically braced frame structure, these self-centering friction damping brace members make the best use of their representative characteristics to minimize residual deformations and to withstand earthquake loads without member replacement. The configuration and response mechanism of self-centering friction damping brace systems are firstly described in this study, and then parametric investigations are conducted through nonlinear time-history analyses performed on numerical single degree-of-freedom spring models. After observing analysis results, adequate design methodologies that optimally account for recentering capability and energy dissipation according to their comparative parameters are intended to be suggested in order to take advantage of energy capacity and to minimize residual deformation simultaneously.

Nonlinear Dynamic Analysis of the Damping Frame Structure System

2012 ◽  
Vol 594-597 ◽  
pp. 886-890 ◽  
Author(s):  
Gan Hong ◽  
Mei Li ◽  
Yi Zhen Yang
Keyword(s):  
Energy Dissipation ◽  
Seismic Response ◽  
Nonlinear Dynamic ◽  
Time History ◽  
Time History Analysis ◽  
Frame Structure ◽  
Force Model ◽  
Operating Characteristics ◽  
Restoring Force ◽  
History Analysis

Abstract. In the paper, take full account of energy dissipation operating characteristics. Interlayer shear-frame structure for the analysis of the Wilson-Θmethod ELASTOPLASTIC schedule, the design of a nonlinear dynamic time history analysis procedure. On this basis, taking into account the restoring force characteristics of the energy dissipation system, the inflection point in the restoring force model treatment, to avoid a result of the calculation results of distortion due to the iterative error. A frame structure seismic response time history analysis results show that: the framework of the energy dissipation significantly lower than the seismic response of the common framework, and its role in the earthquake when more significant.

Experimental investigation of seismic performance of a novel isostatic frame-cladding system

2022 ◽  
pp. 136943322110572
Author(s):  
Xun Chong ◽  
Pu Huo ◽  
Linlin Xie ◽  
Qing Jiang ◽  
Linbing Hou ◽  
...  
Keyword(s):  
Seismic Performance ◽  
Damage Evolution ◽  
Failure Modes ◽  
Static Load ◽  
Precast Concrete ◽  
Frame Structure ◽  
Deformation Capacity ◽  
Load Bearing Capacity ◽  
Cladding Panels ◽  
Energy Dissipation Capacity

A new connection measure between the precast concrete (PC) cladding panel and PC frame structure is proposed to realize a new kind of isostatic frame-cladding system. Three full-scale PC wall-frame substructures were tested under the quasi-static load. These substructures included a bare wall-frame specimen, a specimen with a cladding panel that has no opening, and a specimen with a cladding panel that has an opening in it. The damage evolution, failure mode, load-bearing capacity, deformation capacity, and energy dissipation capacity of three specimens were compared. The results indicated that the motions of the cladding panels and the main structures were uncoupled through the relative clearance of the bottom connections, and three specimens exhibited approximately identical failure modes and seismic performance. Thus, the reliability of this new isostatic system was validated.

Sign in / Sign up

Export Citation Format

Share Document