scholarly journals Learning reference governor for cycle-to-cycle combustion control with misfire avoidance in spark-ignition engines at high exhaust gas recirculation–diluted conditions

2020 ◽  
Vol 21 (10) ◽  
pp. 1819-1834
Author(s):  
Bryan P Maldonado ◽  
Nan Li ◽  
Ilya Kolmanovsky ◽  
Anna G Stefanopoulou
Keyword(s):  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Intake Manifold ◽  
Exhaust Gas ◽  
Model Free ◽  
Recirculation Rate ◽  
Valve Position ◽  
Gas Recirculation ◽  
Reference Governor

Cycle-to-cycle feedback control is employed to achieve optimal combustion phasing while maintaining high levels of exhaust gas recirculation by adjusting the spark advance and the exhaust gas recirculation valve position. The control development is based on a control-oriented model that captures the effects of throttle position, exhaust gas recirculation valve position, and spark timing on the combustion phasing. Under the assumption that in-cylinder pressure information is available, an adaptive extended Kalman filter approach is used to estimate the exhaust gas recirculation rate into the intake manifold based on combustion phasing measurements. The estimation algorithm is adaptive since the cycle-to-cycle combustion variability (output covariance) is not known a priori and changes with operating conditions. A linear quadratic regulator controller is designed to maintain optimal combustion phasing while maximizing exhaust gas recirculation levels during load transients coming from throttle tip-in and tip-out commands from the driver. During throttle tip-outs, however, a combination of a high exhaust gas recirculation rate and an overly advanced spark, product of the dynamic response of the system, generates a sequence of misfire events. In this work, an explicit reference governor is used as an add-on scheme to the closed-loop system in order to avoid the violation of the misfire limit. The reference governor is enhanced with model-free learning which enables it to avoid misfires after a learning phase. Experimental results are reported which illustrate the potential of the proposed control strategy for achieving an optimal combustion process during highly diluted conditions for improving fuel efficiency.

Enhancement of the combustion process in dual-fuel engines at part loads using exhaust gas recirculation

2007 ◽  
Vol 221 (7) ◽  
pp. 877-888 ◽  
Author(s):  
V Pirouzpanah ◽  
R Khoshbakhti Saray
Keyword(s):  
Chemical Kinetics ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Combustion Model ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Performance And Emission ◽  
Dual Fuel Engines ◽  
Gas Recirculation

Dual-fuel engines at part loads inevitably suffer from lower thermal efficiency and higher carbon monoxide and unburned fuel emission. The present work was carried out to investigate the combustion characteristics of a dual-fuel (diesel-gas) engine at part loads, using a single-zone combustion model with detailed chemical kinetics for combustion of natural gas fuel. The authors have developed software in which the pilot fuel is considered as a subsidiary zone and a heat source derived from two superimposedWiebe combustion functions to account for its contribution to ignition of the gaseous fuel and the rest of the total released energy. The chemical kinetics mechanism consists of 112 reactions with 34 species. This quasi-two-zone combustion model is able to establish the development of the combustion process with time and the associated important operating parameters, such as pressure, temperature, heat release rate (HRR), and species concentration. Therefore, this paper describes an attempt to investigate the combustion phenomenon at part loads and using hot exhaust gas recirculation (EGR) to improve the above-mentioned drawbacks and problems. By employing this technique, it is found that lower percentages of EGR and allowance for its thermal and radical effects have a positive influence on performance and emission parameters of dual-fuel engines at part loads. Predicted values show good agreement with corresponding experimental values under special engine operating conditions (quarter-load, 1400 r/min). Implications are discussed in detail.

Measurement of Flame Frequency Response Functions Under Exhaust Gas Recirculation Conditions

2012 ◽  
Vol 134 (9) ◽  
Author(s):  
Joseph Ranalli ◽  
Don Ferguson
Keyword(s):  
Transfer Function ◽  
Carbon Capture ◽  
Transfer Functions ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Exhaust Gas ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Flame Response ◽  
Gas Recirculation

Exhaust gas recirculation has been proposed as a potential strategy for reducing the cost and efficiency penalty associated with postcombustion carbon capture. However, this approach may cause as-yet unresolved effects on the combustion process, including additional potential for the occurrence of thermoacoustic instabilities. Flame dynamics, characterized by the flame transfer function, were measured in traditional swirl stabilized and low-swirl injector combustor configurations, subject to exhaust gas circulation simulated by N2 and CO2 dilution. The flame transfer functions exhibited behavior consistent with a low-pass filter and showed phase dominated by delay. Flame transfer function frequencies were nondimensionalized using Strouhal number to highlight the convective nature of this delay. Dilution was observed to influence the dynamics primarily through its role in changing the size of the flame, indicating that it plays a similar role in determining the dynamics as changes in the equivalence ratio. Notchlike features in the flame transfer function were shown to be related to interference behaviors associated with the convective nature of the flame response. Some similarities between the two stabilization configurations proved limiting and generalization of the physical behaviors will require additional investigation.

The impact of water injection and exhaust gas recirculation on combustion and emissions in a heavy-duty compression ignition engine operated on diesel and gasoline

2019 ◽  
Vol 21 (8) ◽  
pp. 1555-1573 ◽  
Author(s):  
Michael Pamminger ◽  
Buyu Wang ◽  
Carrie M Hall ◽  
Ryan Vojtech ◽  
Thomas Wallner
Keyword(s):  
Thermal Efficiency ◽  
Water Injection ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Exhaust Gas ◽  
Brake Thermal Efficiency ◽  
Fuel Ratio ◽  
Main Injection ◽  
Gas Recirculation ◽  
Diesel Operation

Steady-state experiments were conducted on a 12.4L, six-cylinder heavy-duty engine to investigate the influence of port-injected water and dilution via exhaust gas recirculation (EGR) on combustion and emissions for diesel and gasoline operation. Adding a diluent to the combustion process reduces peak combustion temperatures and can reduce the reactivity of the charge, thereby increasing the ignition-delay and, allowing for more time to premix air and fuel. Experiments spanned water/fuel mass ratios up to 140mass% and exhaust gas recirculation ratios up to 20vol% for gasoline and diesel operation with different injection strategies. Diluting the combustion process with either water or EGR resulted in a significant reduction in nitrogen oxide emissions along with a reduction in brake thermal efficiency. The sensitivity of brake thermal efficiency to water and EGR varied among the fuels and injection strategies investigated. An efficiency breakdown revealed that water injection considerably reduced the wall heat transfer; however, a substantial increase in exhaust enthalpy offset the reduction in wall heat transfer and led to a reduction in brake thermal efficiency. Regular diesel operation with main and post injection exhibited a brake thermal efficiency of 45.8% and a 0.3% reduction at a water/fuel ratio of 120%. The engine operation with gasoline, early pilot, and main injection strategy showed a brake thermal efficiency of 45.0% at 0% water/fuel ratio, and a 1.2% decrease in brake thermal efficiency for a water/fuel ratio of 140%. Using EGR as a diluent reduced the brake thermal efficiency by 0.3% for diesel operation, comparing ratios of 0% and 20% EGR. However, a higher impact on brake thermal efficiency was seen for gasoline operation with early pilot and main injection strategy, with a reduction of about 0.8% comparing 0% and 20% EGR. Dilution by means of EGR exhibited a reduction in nitrogen oxide emissions up to 15 g/kWh; water injection showed only up to 10 g/kWh reduction for the EGR rates and water/fuel ratio investigated.

Diesel Engine Intake Condition Control-Oriented Models for Active Fuel Injection Profile Control

2011 ◽  
Author(s):  
Fengjun Yan ◽  
Junmin Wang
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Fuel Injection ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
High Fidelity ◽  
Exhaust Gas ◽  
Engine Model ◽  
Profile Control ◽  
Gas Recirculation

Fueling control in Diesel engines is not only of significance to the combustion process in one particular cycle, but also influences the subsequent dynamics of air-path loop and combustion events, particularly when exhaust gas recirculation (EGR) is employed. To better reveal such inherently interactive relations, this paper presents a physics-based, control-oriented model describing the dynamics of the intake conditions with fuel injection profile being its input for Diesel engines equipped with EGR and turbocharging systems. The effectiveness of this model is validated by comparing the predictive results with those produced by a high-fidelity 1-D computational GT-Power engine model.

scholarly journals Cyclic NO2:NOx ratio from a diesel engine undergoing transient load steps

2019 ◽  
Vol 22 (1) ◽  
pp. 284-294 ◽  
Author(s):  
FCP Leach ◽  
MH Davy ◽  
MS Peckham
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Formation Mechanisms ◽  
Exhaust Gas ◽  
Work Cycle ◽  
Wide Range ◽  
Gas Recirculation ◽  
Aftertreatment Systems

As the control of real driving emissions continues to increase in importance, the importance of understanding emission formation mechanisms during engine transients similarly increases. Knowledge of the NO2/NOx ratio emitted from a diesel engine is necessary, particularly for ensuring optimum performance of NOx aftertreatment systems. In this work, cycle-to-cycle NO and NOx emissions have been measured using a Cambustion CLD500, and the cyclic NO2/NOx ratio calculated as a high-speed light-duty diesel engine undergoes transient steps in load, while all other engine parameters are held constant across a wide range of operating conditions with and without exhaust gas recirculation. The results show that changes in NO and NOx, and hence NO2/NOx ratio, are instantaneous upon a step change in engine load. NO2/NOx ratios have been observed in line with previously reported results, although at the lightest engine loads and at high levels of exhaust gas recirculation, higher levels of NO2 than have been previously reported in the literature are observed.

Optimization of a diesel engine calibration for operating with a residual glycerol-derived biofuel

2019 ◽  
pp. 146808741989153 ◽  
Author(s):  
Magín Lapuerta ◽  
Ángel Ramos ◽  
Sara Rubio ◽  
Carles Estévez
Keyword(s):  
Particulate Matter ◽  
Fatty Acid ◽  
Diesel Fuel ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Transport Sector ◽  
Exhaust Gas ◽  
Engine Calibration ◽  
Particulate Matter Emissions ◽  
Gas Recirculation

The new European directive for the promotion of renewable energy mandates an increase in the share of advanced and waste-based biofuels in the transport sector. In this study, an advanced glycerol-derived biofuel was used as a component of a ternary blend, denoted as o·bio®. This blend included 27.4 %v/v of fatty acid glycerol formal ester, 69.6 %v/v of fatty acid methyl ester and 3 %v/v of acetals obtained as a by-product of the fatty acid glycerol formal ester production process (which were proved to improve cold-flow properties). Finally, o·bio® was blended with diesel fuel at a content of 20 %v/v. Two operating conditions based on usual driving modes were selected, where the engine calibration could be re-optimized after the change of fuel, corresponding to vehicle velocities of 50 and 70 km/h. Since the main effect of the blend used is to reduce particulate matter emissions, exhaust gas recirculation was increased and injection was delayed, so that the initial benefits in particulate matter emissions could be re-distributed into benefits in both particulate matter and nitrogen oxides (NOx) emissions. From a combined analysis of the particulate matter–NOx trade-off and trying to limit the negative effect of delaying injection on fuel consumption, the final proposal was to set an additional 6% exhaust gas recirculation at 50 km/h and an additional 3% exhaust gas recirculation at 70 km/h, while delaying injection 2 °CA after top dead center at both vehicle operating conditions with respect to the original calibration. The use of the blend along with the optimization of the engine calibration is expected to reduce particulate matter and NOx emissions by around 50% with a vehicle speed condition of 50 km/h and to reduce particulate matter and NOx emissions by around 30% and 40% at 70 km/h with respect to diesel fuel emissions.

An experimental investigation on performance, emissions, and combustion in a manifold injection for different exhaust gas recirculation flowrates in hydrogen—diesel dual-fuel operations

2008 ◽  
Vol 222 (11) ◽  
pp. 2131-2145 ◽  
Author(s):  
N Saravanan ◽  
G Nagarajan
Keyword(s):  
Experimental Investigation ◽  
Exhaust Gas Recirculation ◽  
Intake Manifold ◽  
Dual Fuel ◽  
Injection Timing ◽  
Exhaust Gas ◽  
Exhaust Gases ◽  
Injection Duration ◽  
Performance And Emissions ◽  
Gas Recirculation

Hydrogen is receiving considerable attention as an alternative fuel to replace the rapidly depleting petroleum-based fuels. Its clean burning characteristics help to meet the stringent emission norms. In this experimental investigation a single-cylinder diesel engine was converted to operate in hydrogen—diesel dual-fuel mode. Hydrogen was injected in the intake manifold and the diesel was injected directly inside the cylinder. The injection timing and the injection duration of hydrogen were optimized on the basis of performance and emissions. Best results were obtained with hydrogen injection at gas exchange top dead centre with an injection duration of 30° crank angle. The flowrate of hydrogen was optimized as 7.5l/min with optimized injection timing and duration. The optimized exhaust gas recirculation (EGR) flowrate was 20 per cent at 75 per cent load. The optimized timings were chosen on the basis of performance, emission, and combustion characteristics. The EGR technique was adopted in the hydrogen—diesel dual-fuel mode by varying the EGR flowrate from 0 per cent to 25 per cent in steps of 5 per cent. The maximum quantity of exhaust gases recycled during the test was 25 per cent (up to 75 per cent load); beyond that unstable combustion was observed with an increase in smoke. The brake thermal efficiency with 20 per cent EGR decreases by 9 per cent compared with diesel. The nitrogen oxide (NO x) emission in hydrogen manifold injection decreases by threefold with 20 per cent EGR operation at full load. The NO x emission tends to reduce drastically with increase in the EGR percentage at all load conditions owing to the increase in heat capacity of the exhaust gases. The smoke decreases by 80 per cent in the dual-fuel operation compared with diesel at 75 per cent load.

Effects of Exhaust Gas Recirculation on Particulate Morphology from a Diesel Engine

2013 ◽  
Vol 664 ◽  
pp. 926-930
Author(s):  
Wei Zhang ◽  
Xiao Dong Wang ◽  
Rui Sun ◽  
Jian Wei Sun ◽  
Wei Han
Keyword(s):  
Particle Size ◽  
Diesel Engine ◽  
Primary Particle ◽  
Morphological Characteristics ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Injection System ◽  
Exhaust Gas ◽  
Aggregate Particle ◽  
Gas Recirculation

The effects of EGR operating mode on particulate morphology were investigated for a 5.79-liter diesel engine which was equipped with a turbocharged and inter-cooled air induction system, a common-rail direct fuel injection system, and an EGR system. Morphological characteristics, such as primary particle size, number concentration and aggregate particle size were investigated by a transmission electron microscope (TEM) analysis and a electrical low pressure impactor (ELPI) under engine operating conditions of 0.41 in fuel/air ratio at different exhaust gas recirculation (EGR) rate from 0～35%. The experimental results indicated that primary particle were in the range of 17.05nm～18.34nm, which increased with increased EGR rate. As EGR rate increased, aggregate particle size were measured in a narrow range from 120nm to 170nm.

scholarly journals The effect of engine operating conditions on exhaust gas recirculation cooler fouling

2018 ◽  
Vol 126 ◽  
pp. 509-520 ◽  
Author(s):  
Michael J. Lance ◽  
Zachary G. Mills ◽  
Joshua C. Seylar ◽  
John M.E. Storey ◽  
C. Scott Sluder
Keyword(s):  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Exhaust Gas ◽  
Gas Recirculation
Sign in / Sign up

Export Citation Format

Share Document