scholarly journals Optimization of gasoline compression ignition combustion with ozone addition and two-stage direct-injection at middle loads

2021 ◽  
pp. 146808742098457
Author(s):  
Yoshimitsu Kobashi ◽  
Tu Dan Dan Da ◽  
Ryuya Inagaki ◽  
Gen Shibata ◽  
Hideyuki Ogawa
Keyword(s):  
Ozone Concentration ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Pressure Rise ◽  
Maximum Pressure ◽  
Injection Timing ◽  
Compression Ignition ◽  
Ozone Addition ◽  
Primary Reference

Ozone (O3) was introduced into the intake air to control the ignition in a gasoline compression ignition (GCI) engine. An early fuel injection at −68 °CA ATDC was adopted to mix the fuel with the reactive O-radicals decomposed from the O3, before the reduction of the O-radicals due to their recombination would take place. The second injection was implemented near top dead center to optimize the profile of the heat release rate. The engine experiments were performed around the indicated mean effective pressure (IMEP) of 0.67 MPa with a primary reference fuel, octane number 90 (PRF90), maintaining the 15% intake oxygen concentration with the EGR. The quantity of the first injection, the second injection timing as well as the ozone concentration were changed as experimental parameters. The results showed that the GCI operation with the ozone addition makes it possible to reduce the maximum pressure rise rate while attaining high thermal efficiency, compared to that without the ozone. Appropriate combinations of the ozone concentration and the first injection quantity achieve low smoke and NOx emissions. Further, the ozone-assisted GCI operation was compared with conventional diesel operation. The results showed that the indicated thermal efficiency of the ozone-assisted GCI combustion is slightly lower than that of the conventional diesel combustion, but that GCI assisted with ozone is highly advantageous to the smoke and NOx emissions.

Factors Affecting Performance of Dual Fuel Compression Ignition Engines

2013 ◽  
Vol 388 ◽  
pp. 217-222
Author(s):  
Mohamed Mustafa Ali ◽  
Sabir Mohamed Salih
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Factors Affecting

Compression Ignition Diesel Engine use Diesel as conventional fuel. This has proven to be the most economical source of prime mover in medium and heavy duty loads for both stationary and mobile applications. Performance enhancements have been implemented to optimize fuel consumption and increase thermal efficiency as well as lowering exhaust emissions on these engines. Recently dual fueling of Diesel engines has been found one of the means to achieve these goals. Different types of fuels are tried to displace some of the diesel fuel consumption. This study is made to identify the most favorable conditions for dual fuel mode of operation using Diesel as main fuel and Gasoline as a combustion improver. A single cylinder naturally aspirated air cooled 0.4 liter direct injection diesel engine is used. Diesel is injected by the normal fuel injection system, while Gasoline is carbureted with air using a simple single jet carburetor mounted at the air intake. The engine has been operated at constant speed of 3000 rpm and the load was varied. Different Gasoline to air mixture strengths investigated, and diesel injection timing is also varied. The optimum setting of the engine has been defined which increased the thermal efficiency, reduced the NOx % and HC%.

scholarly journals Investigation Into Reactivity Separation Between Direct Injected and Premixed Fuels in RCCI Combustion Mode

2019 ◽  
Author(s):  
Ziming Yan ◽  
Brian Gainey ◽  
Deivanayagam Hariharan ◽  
Benjamin Lawler
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Efficiency ◽  
High Reactivity ◽  
Injection System ◽  
Injection Timing ◽  
Nox Emissions ◽  
Light Duty ◽  
Primary Reference

Abstract This experimental study focuses on the effects of the reactivity separation between the port injected fuel and the direct injection fuel, the amount of external-cooled exhaust gas recirculation (EGR), and the direct injection timing of the high reactivity fuel on Reactivity Controlled Compression Ignition (RCCI) combustion. The experiments were conducted on a light-duty, single-cylinder diesel engine with a production GM/Isuzu engine head and piston and a retrofitted port fuel injection system. The global charge-mass equivalence ratio, ϕ′, was fixed at 0.32 throughout all of the experiments. To investigate the effects of the fuel reactivity separation, different Primary Reference Fuels (PRF) were port injected, with the PRF number varying from 50 to 90. To investigate the effects of EGR, an EGR range of 0 to 55% was used. To investigate the effects of the injection timing, an injection timing window of −65 to −45 degrees ATDC was chosen. The results indicate that there are several tradeoffs. First, decreasing the port injected fuel reactivity (increasing the PRF number) delays combustion phasing, decreases the combustion efficiency by up to 9%, increases the gross indicated thermal efficiency up to 22%, enhances the combustion sensitivity to the direct injection timing, and slightly increases the UHC, CO, and NOx emissions. Second, increasing the EGR percentage delays combustion phasing, lowers the peak heat release rate, and lowers the NOx emissions. The combustion efficiency first increases and then decreases with EGR percentage for high reactivity fuels (low PRF number), but only decreases for low reactivity fuels. Finally, delaying the injection timing advances combustion phasing and increases the combustion efficiency, but decreases the gross indicated thermal efficiency and increases the NOx emissions. Across all of the experiments, delays in CA50 increase the gross indicated thermal efficiency and decrease the combustion efficiency, which represents an inherent tradeoff for RCCI combustion on a light-duty engine.

Experimental Investigation of Direct Fuel Injection into Low-Oxygen Recompression Interval in a Homogenous Charge Compression Ignition Engine

2021 ◽  
pp. 1-25
Author(s):  
Ratnak Sok ◽  
Jin Kusaka
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Combustion Noise ◽  
Maximum Pressure ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Single Digit ◽  
Homogenous Charge Compression Ignition

Abstract This work analyzed measured data from a single-cylinder engine operated under gasoline direction injection homogenous charge compression ignition (GDI-HCCI) mode. The experiments were conducted at a 0.95 equivalence ratio (φ) under 0.5 MPa indicated mean effective pressure and 1500RPM. A side-mounted injector delivered primary reference fuel (octane number 90) into the combustion chamber during negative valve overlap (NVO). Advanced combustion phase CA50 were observed as a function of the start of injection (SOI) timings. Under φ=0.95, peak NVO in-cylinder pressures were lower than motoring for single and split injections, emphasizing that NVO reactions were endothermic. Zero-dimensional kinetics calculations showed classical reformate species (C3H6, C2H4, CH4) from the NVO rich mixture increased almost linearly due to SOI timings, while H2 and CO were typically low. These kinetically reformed species shortened predicted ignition delays. This work also analyzed the effects of intake pressure and single versus double pulses injections on CA50, burn duration, peak cylinder pressure, combustion noise, thermal efficiency, and emissions. Advanced SOI (single-injection) generated excessive combustion noise metrics over constraint limits, but the double-pulse injection could significantly reduce the metrics (Ringing Intensity ≤ 5 MW/m2, Maximum Pressure Rise Rate = 0.6 MPa/CA) and NOx emission. The engine's net indicated thermal efficiency reached 41% under GDI-HCCI mode against 36% under SI mode for the same operating conditions. Under GDI-HCCI mode and without spark-ignition, late fuel injection in the intake stroke could reduce NOx to a single digit.

scholarly journals Impact of injection strategies on combustion characteristics, efficiency and emissions of gasoline compression ignition operation in a heavy-duty multi-cylinder engine

2018 ◽  
Vol 21 (8) ◽  
pp. 1426-1440 ◽  
Author(s):  
Buyu Wang ◽  
Michael Pamminger ◽  
Ryan Vojtech ◽  
Thomas Wallner
Keyword(s):  
High Temperature ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Pressure Rise ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Gas Recirculation ◽  
Direct Fuel Injection

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low-temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high-temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Furthermore, for high-temperature gasoline compression ignition, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high-temperature gasoline compression ignition combustion with port and direct injection. Engine testing was conducted at an engine speed of 1038 r/min and brake mean effective pressure of 1.4 MPa for three injection strategies, late pilot injection, early pilot injection, and port/direct fuel injection. The impact on engine performance and emissions with respect to varying the combustion phasing were quantified within this study. At the same combustion phasing, early pilot injection and port/direct fuel injection had an earlier start of combustion and higher maximum pressure rise rates than late pilot injection attributable to more premixed fuel from pilot or port injection; however, brake thermal efficiencies were higher with late pilot injection due to reduced heat transfer. Early pilot injection also exhibited the highest cylinder-to-cylinder variations due to differences in injector behavior as well as the spray/wall interactions affecting mixing and evaporation process. Overall, peak brake thermal efficiency of 46.1% and 46% for late pilot injection and port/direct fuel injection was achieved comparable to diesel baseline (45.9%), while early pilot injection showed the lowest brake thermal efficiency (45.3%).

Influence of fuel injection strategies on efficiency and particulate emissions of gasoline and ethanol blends in a turbocharged multi-cylinder direct injection engine

2019 ◽  
Vol 22 (1) ◽  
pp. 152-164 ◽  
Author(s):  
Ripudaman Singh ◽  
Taehoon Han ◽  
Mohammad Fatouraie ◽  
Andrew Mansfield ◽  
Margaret Wooldridge ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Multiple Injection ◽  
Fuel Mass ◽  
Direct Injection Engine ◽  
Fuel Blends ◽  
Ethanol Blends ◽  
Injection Strategies

The effects of a broad range of fuel injection strategies on thermal efficiency and engine-out emissions (CO, total hydrocarbons, NOx and particulate number) were studied for gasoline and ethanol fuel blends. A state-of-the-art production multi-cylinder turbocharged gasoline direct injection engine equipped with piezoelectric injectors was used to study fuels and fueling strategies not previously considered in the literature. A large parametric space was considered including up to four fuel injection events with variable injection timing and variable fuel mass in each injection event. Fuel blends of E30 (30% by volume ethanol) and E85 (85% by volume ethanol) were compared with baseline E0 (reference grade gasoline). The engine was operated over a range of loads with intake manifold absolute pressure from 800 to 1200 mbar. A combined application of ethanol blends with a multiple injection strategy yielded considerable improvement in engine-out particulate and gaseous emissions while maintaining or slightly improving engine brake thermal efficiency. The weighted injection spread parameter defined in this study, combined with the weighted center of injection timing defined in the previous literature, was found well suited to characterize multiple injection strategies, including the effects of the number of injections, fuel mass in each injection and the dwell time between injections.

Experimental investigations on combustion of jatropha methyl ester in a turbocharged direct-injection diesel engine

2008 ◽  
Vol 222 (10) ◽  
pp. 1865-1877 ◽  
Author(s):  
K Anand ◽  
R P Sharma ◽  
P S Mehta
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Peak Pressure ◽  
Direct Injection ◽  
Pressure Rise ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Gas Temperature

Suitability of vegetable oil as an alternative to diesel fuel in compression ignition engines has become attractive, and research in this area has gained momentum because of concerns on energy security, high oil prices, and increased emphasis on clean environment. The experimental work reported here has been carried out on a turbocharged direct-injection multicylinder truck diesel engine using diesel fuel and jatropha methyl ester (JME)-diesel blends. The results of the experimental investigation indicate that an increase in JME quantity in the blend slightly advances the dynamic fuel injection timing and lowers the ignition delay compared with the diesel fuel. A maximum rise in peak pressure limited to 6.5 per cent is observed for fuel blends up to 40 per cent JME for part-load (up to about 50 per cent load) operations. However, for a higher-JME blend, the peak pressures decrease at higher loads remained within 4.5 per cent. With increasing proportion of JME in the blend, the peak pressure occurrence slightly advances and the maximum rate of pressure rise, combustion duration, and exhaust gas temperature decrease by 9 per cent, 15 per cent and 17 per cent respectively. Although the changes in brake thermal efficiencies for 20 per cent and 40 per cent JME blends compared with diesel fuel remain insignificant, the 60 per cent JME blend showed about 2.7 per cent improvement in the brake thermal efficiency. In general, it is observed that the overall performance and combustion characteristics of the engine do not alter significantly for 20 per cent and 40 per cent JME blends but show an improvement over diesel performance when fuelled with 60 per cent JME blend.

A Numerical Study of NOx Reduction for a DI Diesel Engine With Complex Geometry

2004 ◽  
Vol 126 (1) ◽  
pp. 13-20 ◽  
Author(s):  
Renshan Liu ◽  
Chao Zhang
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Complex Geometry ◽  
Numerical Study ◽  
Direct Injection ◽  
Nox Reduction ◽  
Geometrical Parameters ◽  
Injection Timing ◽  
Di Diesel Engine

A numerical study of NOx reduction for a Direct Injection (DI) Diesel engine with complex geometry, which includes intake/exhaust ports and moving valves, was carried out using the commercial computational fluid dynamics software KIVA-3v. The numerical simulations were conducted to investigate the effects of engine operating and geometrical parameters, including fuel injection timing, fuel injection duration, and piston bowl depth, on the NOx formation and the thermal efficiency of the DI Diesel engine. The tradeoff relationships between the reduction in NOx and the decrease in thermal efficiency were established.

Investigation of the Effect of Injection and Control Strategies on Combustion Instability in Reactivity-Controlled Compression Ignition Engines

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
David T. Klos ◽  
Sage L. Kokjohn
Keyword(s):  
Direct Injection ◽  
Combustion Instability ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Cfd Modeling ◽  
Surface Model ◽  
Injection Timing ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition

This paper uses detailed computational fluid dynamics (CFD) modeling with the kiva-chemkin code to investigate the influence of injection timing, combustion phasing, and operating conditions on combustion instability. Using detailed CFD simulations, a large design of experiments (DOE) is performed with small perturbations in the intake and fueling conditions. A response surface model (RSM) is then fit to the DOE results to predict cycle-to-cycle combustion instability. Injection timing had significant tradeoffs between engine efficiency, emissions, and combustion instability. Near top dead center (TDC) injection timing can significantly reduce combustion instability, but the emissions and efficiency drop close to conventional diesel combustion levels. The fuel split between the two direct injection (DI) injections has very little effect on combustion instability. Increasing exhaust gas recirculation (EGR) rate, while making adjustments to maintain combustion phasing, can significantly reduce peak pressure rise rate (PPRR) variation until the engine is on the verge of misfiring. Combustion phasing has a very large impact on combustion instability. More advanced phasing is much more stable, but produces high PPRRs, higher NOx levels, and can be less efficient due to increased heat transfer losses. The results of this study identify operating parameters that can significantly improve the combustion stability of dual-fuel reactivity-controlled compression ignition (RCCI) engines.

Fuel Stratification and Partially Premixed Combustion With Neat n-Butanol in a Compression Ignition Engine

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Shouvik Dev ◽  
Tongyang Gao ◽  
Xiao Yu ◽  
Mark Ives ◽  
Ming Zheng
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Premixed Combustion ◽  
Injection Timing ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Stratification ◽  
Partially Premixed Combustion ◽  
Partially Premixed ◽  
Ci Engines

Homogeneous charge compression ignition (HCCI) has been considered as an ideal combustion mode for compression ignition (CI) engines due to its superb thermal efficiency and low emissions of nitrogen oxides (NOx) and particulate matter. However, a challenge that limits practical applications of HCCI is the lack of control over the combustion rate. Fuel stratification and partially premixed combustion (PPC) have considerably improved the control over the heat release profile with modulations of the ratio between premixed fuel and directly injected fuel, as well as injection timing for ignition initiation. It leverages the advantages of both conventional direct injection compression ignition and HCCI. In this study, neat n-butanol is employed to generate the fuel stratification and PPC in a single cylinder CI engine. A fuel such as n-butanol can provide additional benefits of even lower emissions and can potentially lead to a reduced carbon footprint and improved energy security if produced appropriately from biomass sources. Intake port fuel injection (PFI) of neat n-butanol is used for the delivery of the premixed fuel, while the direct injection (DI) of neat n-butanol is applied to generate the fuel stratification. Effects of PFI-DI fuel ratio, DI timing, and intake pressure on the combustion are studied in detail. Different conditions are identified at which clean and efficient combustion can be achieved at a baseline load of 6 bar IMEP. An extended load of 14 bar IMEP is demonstrated using stratified combustion with combustion phasing control.

scholarly journals Effect of Premixed Fuel Preparation for Partially Premixed Combustion With a Low Octane Gasoline on a Light-Duty Multicylinder Compression Ignition Engine

2015 ◽  
Vol 137 (11) ◽  
Author(s):  
Adam B. Dempsey ◽  
Scott Curran ◽  
Robert Wagner ◽  
William Cannella
Keyword(s):  
High Pressure ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Premixed Combustion ◽  
Injection System ◽  
Injection Timing ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Partially Premixed Combustion ◽  
Injection Strategies

Gasoline compression ignition (GCI) concepts with the majority of the fuel being introduced early in the cycle are known as partially premixed combustion (PPC). Previous research on single- and multicylinder engines has shown that PPC has the potential for high thermal efficiency with low NOx and soot emissions. A variety of fuel injection strategies have been proposed in the literature. These injection strategies aim to create a partially stratified charge to simultaneously reduce NOx and soot emissions while maintaining some level of control over the combustion process through the fuel delivery system. The impact of the direct injection (DI) strategy to create a premixed charge of fuel and air has not previously been explored, and its impact on engine efficiency and emissions is not well understood. This paper explores the effect of sweeping the direct injected pilot timing from −91 deg to −324 deg ATDC, which is just after the exhaust valve closes (EVCs) for the engine used in this study. During the sweep, the pilot injection consistently contained 65% of the total fuel (based on command duration ratio), and the main injection timing was adjusted slightly to maintain combustion phasing near top dead center. A modern four cylinder, 1.9 l diesel engine with a variable geometry turbocharger (VGT), high pressure common rail injection system, wide included angle injectors, and variable swirl actuations was used in this study. The pistons were modified to an open bowl configuration suitable for highly premixed combustion modes. The stock diesel injection system was unmodified, and the gasoline fuel was doped with a lubricity additive to protect the high pressure fuel pump and the injectors. The study was conducted at a fixed speed/load condition of 2000 rpm and 4.0 bar brake mean effective pressure (BMEP). The pilot injection timing sweep was conducted at different intake manifold pressures, swirl levels, and fuel injection pressures. The gasoline used in this study has relatively high fuel reactivity with a research octane number of 68. The results of this experimental campaign indicate that the highest brake thermal efficiency (BTE) and lowest emissions are achieved simultaneously with the earliest pilot injection timings (i.e., during the intake stroke).

Sign in / Sign up

Export Citation Format

Share Document