Effects of processing parameters on in situ synthesis of β-Sialon/ZrN/ZrO2 from fly ash and zircon

2013 ◽  
Vol 17 (sup2) ◽  
pp. s136-s141
Author(s):  
B. Ma ◽  
B. Li ◽  
Y. Li ◽  
Y. Ding ◽  
C. Yan ◽  
...  
2018 ◽  
Vol 57 (46) ◽  
pp. 15632-15637 ◽  
Author(s):  
Bangda Wang ◽  
Yuexi Zhou ◽  
Lei Li ◽  
Hui Xu ◽  
Yinglong Sun ◽  
...  

2014 ◽  
Vol 53 (37) ◽  
pp. 14282-14290 ◽  
Author(s):  
Swati Varshney ◽  
Anil Ohlan ◽  
Vinod Kumar Jain ◽  
Ved Prakash Dutta ◽  
Sundeep K. Dhawan
Keyword(s):  
Fly Ash ◽  

2014 ◽  
Vol 1061-1062 ◽  
pp. 526-529
Author(s):  
Jing Liang ◽  
Chao Wang ◽  
Sui Yuan Chen ◽  
Chang Sheng Liu ◽  
Cheng Yu Yang

B4C/TiNi mixed powders with different composition (10B4C+90TiNi and 20B4C+80TiNi in wt. %) prepasted on Ti-6Al-4V substrates were scanned by a FL-Dlight02-3000W semiconductor laser to obtain TiBx+TiC reinforced graded composite coatings. The influences of the processing parameters on the microstructure of the coatings were studied. Optimal processing parameters were obtained with laser power (P) 1700W/1900W, laser scanning speed (V) 6.67mm/s and defocus length 310mm. The microstructures and phases of the coatings were analyzed with OM, SEM and XRD respectively. Graded composite coatings with in-situ synthesis of TiC, TiB and TiB2 reinforcements in the matrix of Ti2Ni and TiNi were obtained.


Author(s):  
Dongzhe Zhang ◽  
Yunze Li ◽  
Hui Wang ◽  
Weilong Cong

Abstract Nickel-Titanium (NiTi) alloy is difficult to be machined and fabricated due to its properties of rapid work-hardening and superelasticity. Traditional manufacturing methods, such as casting, vacuum arc melting, and hot-isostatic pressing, have disadvantages of high cost, time-consuming, and limitation in the complexity of parts’ fabrication. In order to reduce or solve these problems, laser additive manufacturing methods have been studied in the fabrication of NiTi alloy. Among the investigations, laser engineered net-shaping (LENS) in-situ synthesis of NiTi from blended Ni and Ti powders shows its unique advantage of cost-effectiveness and flexibility in tailoring NiTi’s phase transformation properties. In addition, it is reported that LENS in-situ synthesized NiTi parts have comparable properties with NiTi alloys fabricated from pre-alloyed powders. However, there are no existing investigations on the effects of processing parameters on the mechanical properties of the LENS in-situ fabricated NiTi parts. The processing parameters would have great influences on the properties of the LENS in-situ synthesized NiTi parts. This paper, for the first time, reports the effects of laser power, powder feeding rate, and Z increment of the deposition head on microstructure, microhardness, and Young’s modulus of the LENS in-situ synthesized NiTi parts.


2019 ◽  
Vol 236 ◽  
pp. 644-648 ◽  
Author(s):  
A. De Rossi ◽  
L. Simão ◽  
M.J. Ribeiro ◽  
R.M. Novais ◽  
J.A. Labrincha ◽  
...  

2019 ◽  
Vol 102 (12) ◽  
pp. 7665-7677 ◽  
Author(s):  
Yanan Zhang ◽  
Wei Kang ◽  
Hongjing Han ◽  
Haiying Wang ◽  
Yanguang Chen ◽  
...  

2017 ◽  
Vol 120 (3) ◽  
pp. 303-322
Author(s):  
D. Pienaar ◽  
B.M. Guy ◽  
C. Pienaar ◽  
K.S. Viljoen

Abstract Mineralogical and textural variability of ores from different sources commonly leads to processing inefficiencies, particularly when a processing plant is designed to treat ore from a single source (i.e. ore of a relatively uniform composition). The bulk of the Witwatersrand ore in the Klerksdorp goldfield, processed at the AngloGold Ashanti Great Noligwa treatment plant, is derived from the Vaal Reef (>90%), with a comparatively small contribution obtained from the Crystalkop Reef (or C-Reef). Despite the uneven contribution, it is of critical importance to ensure that the processing parameters are optimized for the treatment of both the Vaal and C-Reefs. This paper serves to document the results of a geometallurgical study of the C-Reef at the Great Noligwa gold mine in the Klerksdorp goldfield of South Africa, with the primary aim of assessing the suitability of the processing parameters that are in use at the Great Noligwa plant. The paper also draws comparisons between the C-Reef and the Vaal Reef A-facies (Vaal Reef) and attempts to explain minor differences in the recovery of gold and uranium from these two sources. Three samples of the C-Reef were collected in-situ from the underground operations at Great Noligwa mine for mineralogical analyses and metallurgical tests. Laboratory-scale leach tests for gold (cyanide) and uranium (sulphuric acid) were carried out using dissolution conditions similar to that in use at the Great Noligwa plant, followed by further diagnostic leaching in the case of gold. The gold in the ore was found to be readily leachable with recoveries ranging from 95% to 97% (as opposed to 89% to 93% for the Vaal Reef). Additional recoveries were achieved in the presence of excess cyanide (96% to 98%). The recovery of uranium varied between 72% and 76% (as opposed to 30% to 64% for the Vaal Reef), which is substantially higher than predicted, given the amount of brannerite in the ore, which is generally regarded as refractory. Thus, the higher uranium recoveries from the C-Reef imply that a proportion of the uranium was recovered by the partial dissolution of brannerite. As the Vaal Reef contain high amounts of chlorite (3% to 8%), which is an important acid consumer, it is considered likely that this could have reduced the effectiveness of the H2SO4 leach in the case of the ore of the Vaal Reef. Since the gold and uranium recoveries from the C-Reef were higher than the recoveries from the Vaal Reef, the results demonstrate that the processing parameters used for treatment of the Vaal Reef are equally suited to the treatment of the C-Reef. Moreover, small processing modifications, such as increased milling and leach retention times, may well increase the recovery of gold (particularly when e.g. coarse gold, or unexposed gold, is present).


Sign in / Sign up

Export Citation Format

Share Document