Pathways of volcanic glass alteration in laboratory experiments through inorganic and microbially-mediated processes

Clay Minerals ◽  
2013 ◽  
Vol 48 (3) ◽  
pp. 423-445 ◽  
Author(s):  
J. Cuadros ◽  
B. Afsin ◽  
P. Jadubansa ◽  
M. Ardakani ◽  
C. Ascaso ◽  
...  

AbstractRhyolitic obsidian was reacted with natural waters to study the effect of water chemistry and biological activity on the composition and formation mechanisms of clay. Two sets of experiments (18 months, 6 years) used fresh, hypersaline water (Mg-Na-SO4-Cl- and NaCl-rich) and seawater. The 6-year experiments produced the transformation of obsidian into quartz, apparently by in situ re-crystallization (Cuadros et al., 2012). The most abundant neoformed clay was dioctahedral (typically montmorillonite), indicating chemical control by the glass (where Al > Mg). Altered glass morphology and chemistry in the 18-months experiments indicated in situ transformation to clay. Magnesium-rich (saponite) clay formed under water-chemistry control in the bulk and within biofilms with elevated Mg concentration (Cuadros et al., 2013). The contact between microbial structures and glass was very intimate. Glass transformation into quartz may be due to some characteristic of the obsidian and/or alteration conditions. Such combination needs not to be uncommon in nature and opens new possibilities of quartz origin.

2021 ◽  
Vol 11 (4) ◽  
pp. 1570
Author(s):  
Bogdan Ioan Băcilă ◽  
Hyunkook Lee

This paper presents a subjective study conducted on the perception of auditory attributes depending on listener position and head orientation in an enclosed space. Two elicitation experiments were carried out using the repertory grid technique—in-situ and laboratory experiments—which aimed to identify perceptual attributes among 10 different combinations of the listener’s positions and head orientations in a concert hall. It was found that, between the in-situ and laboratory experiments, the listening positions and head orientations were clustered identically. Ten salient perceptual attributes were identified from the data obtained from the laboratory experiment. Whilst these included conventional attributes such as ASW (apparent source width) and LEV (listener envelopment), new attributes such as PRL (perceived reverb loudness), ARW (apparent reverb width) and Reverb Direction were identified, and they are hypothesised to be sub-attributes of LEV (listener envelopment). Timbral characteristics such as Reverb Brightness and Echo Brightness were also identified as salient attributes, which are considered to potentially contribute to the overall perceived clarity.


2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Kylie Owen ◽  
Kentaro Saeki ◽  
Joseph D. Warren ◽  
Alessandro Bocconcelli ◽  
David N. Wiley ◽  
...  

AbstractFinding prey is essential to survival, with marine predators hypothesised to track chemicals such as dimethyl sulfide (DMS) while foraging. Many predators are attracted to artificially released DMS, and laboratory experiments have shown that zooplankton grazing on phytoplankton accelerates DMS release. However, whether natural DMS concentrations are useful for predators and correlated to areas of high prey biomass remains a fundamental knowledge gap. Here, we used concurrent hydroacoustic surveys and in situ DMS measurements to present evidence that zooplankton biomass is spatially correlated to natural DMS concentration in air and seawater. Using agent simulations, we also show that following gradients of DMS would lead zooplankton predators to areas of higher prey biomass than swimming randomly. Further understanding of the conditions and scales over which these gradients occur, and how they are used by predators, is essential to predicting the impact of future changes in the ocean on predator foraging success.


Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2449
Author(s):  
Marion Baillieul ◽  
Emeline Baudet ◽  
Karine Michel ◽  
Jonathan Moreau ◽  
Petr Němec ◽  
...  

The objective of this study is to demonstrate the successful functionalization of the surface of a chalcogenide infrared waveguide with the ultimate goal of developing an infrared micro-sensor device. First, a polyisobutylene coating was selected by testing its physico-chemical compatibility with a Ge-Sb-Se selenide surface. To simulate the chalcogenide platform infrared sensor, the detection of benzene, toluene, and ortho-, meta- and para-xylenes was efficaciously performed using a polyisobutylene layer spin-coated on 1 and 2.5 µm co-sputtered selenide films of Ge28Sb12Se60 composition deposited on a zinc selenide prism used for attenuated total reflection spectroscopy. The thickness of the polymer coating was optimized by attenuated total reflection spectroscopy to achieve the highest possible attenuation of water absorption while maintaining the diffusion rate of the pollutant through the polymer film compatible with the targeted in situ analysis. Then, natural water, i.e., groundwater, wastewater, and seawater, was sampled for detection measurement by means of attenuated total reflection spectroscopy. This study is a valuable contribution concerning the functionalization by a hydrophobic polymer compatible with a chalcogenide optical sensor designed to operate in the mid-infrared spectral range to detect in situ organic molecules in natural water.


2007 ◽  
Vol 4 (4) ◽  
pp. 2441-2491 ◽  
Author(s):  
M. S. Twardowski ◽  
H. Claustre ◽  
S. A. Freeman ◽  
D. Stramski ◽  
Y. Huot

Abstract. During the BIOSOPE field campaign October–December 2004, measurements of inherent optical properties from the surface to 500 m depth were made with a ship profiler at stations covering over ~8000 km through the Southeast Pacific Ocean. Data from a ~3000 km section containing the very clearest waters in the central gyre are reported here. The total volume scattering function at 117°, βt(117°), was measured with a WET Labs ECO-BB3 sensor at 462, 532, and 650 nm with estimated uncertainties of 2×10−5, 5×10−6, and 2×10−6 m−1 sr−1, respectively. These values were approximately 6%, 3%, and 3% of the scattering by pure seawater at their respective wavelengths. From a methodological perspective, there were several results: – bbp distributions were resolvable even though some of the values from the central gyre were an order of magnitude lower than the lowest previous measurements in the literature; – Direct in-situ measurements of instrument dark offsets were necessary to accurately resolve backscattering at these low levels; – accurate pure seawater backscattering values are critical in determining particulate backscattering coefficients in the open ocean (not only in these very clear waters); the pure water scattering values determined by Buiteveld et al. (1994) with a [1 + 0.3S/37] adjustment for salinity based on Morel (1974) appear to be the most accurate estimates, with aggregate accuracies as low as a few percent; and – closure was demonstrated with subsurface reflectance measurements reported by Morel et al. (2007) within instrument precisions, a useful factor in validating the backscattering measurements. This methodology enabled several observations with respect to the hydrography and the use of backscattering as a biogeochemical proxy: – The clearest waters sampled were found at depths between 300 and 350 m, from 23.5° S, 118° W to 26° S, 114° W, where total backscattering at 650 nm was not distinguishable from pure seawater; – Distributions of particulate backscattering bbp across the central gyre exhibited a broad particle peak centered ~100 m; – The particulate backscattering ratio typically ranged between 0.4% and 0.6% through the majority of the central gyre from the surface to ~210 m, indicative of "soft" water-filled particles with low bulk refractive index; and – bbp at 532 and 650 nm showed a distinct secondary deeper layer centered ~230 m that was absent in particulate attenuation cp data. The particulate backscattering ratio was significantly higher in this layer than in the rest of the water column, reaching 1.2% in some locations. This high relative backscattering, along with the pigment composition and ecological niche of this layer, appear to be consistent with the coccolithophorid F. profunda. Moreover, results were consistent with several expectations extrapolated from theory and previous work in oceanic and coastal regions, supporting the conclusion that particulate and total backscattering could be resolved in these extremely clear natural waters.


2021 ◽  
Author(s):  
Juan Manuel Leon ◽  
Shehadeh K. Masalmeh ◽  
Siqing Xu ◽  
Ali M. AlSumaiti ◽  
Ahmed A. BinAmro ◽  
...  

Abstract Assessing polymer injectivity for EOR field applications is highly important and challenging. An excessive injectivity reduction during and after polymer injection may potentially affect the well integrity and recovery efficiency and consequently, injection strategy and the economics of the polymer projects. Moreover, well conditions such as skin, completion configuration, and injection water quality can significantly impact polymer injectivity. Additionally, the presence of fractures or micro-fractures may govern injection pressure. In contrast, historic field applications have shown that polymer injectivity is in general better than expected from simulations or laboratory data. In the laboratory experiments, the polymer injectivity has been evaluated by injection of significant amounts of pore volumes of polymer at relevant well-injection rates. In addition, several experiments were performed to measure the complex in-situ rheology expected to dominate the flow near the wellbore This paper presents the analysis of the the world's first polymer injectivity test (PIT) conducted in a high temperature and high salinity (HTHS) carbonate reservoir in Abu Dhabi as part of a comprehensive de-risking program for a new polymer-based EOR scheme proposed by ADNOC for these challenging carbonate reservoirs (see Masalmeh et. al., 2014). The de-risking program includes an extensive laboratory experimental program and field injectivity test to ensure that the identified polymer can be injected and propagated in the target formation before multi-well pilot and full-field implementation stages. Experimental laboratory data and the field injectivity test results are presented in earlier publications (Masalmeh et. al., 2019; Rachapudi et. al., 2020) and references therein. This PIT is the world's first polymer injectivity test in a carbonate reservoir under such harsh conditions of high salinity, high content of divalent ions and high temperature. In addition, the polymer used during the test has never been field-tested before. Therefore, the results of the PIT interpretation will help to de-risk the suitable polymer for the future inter-well pilot for the new proposed EOR Polymer-based scheme and it is a game-changer to unlock several opportunities for different Chemical EOR applications on full-field scale in other reservoirs with similar characteristics. A single well radial simulation model was built to integrate the surveillance data during PIT and the extensive laboratory experiments. Morever, multiple Pressure Fall Off Tests (PFOs) during the same periods were analyzed and intergaretd in the model.The study assessed the effect of polymer viscosity on mobility reduction, evaluated the polymer bank propagation, investigated the effect of the skin build-up, residual resistance factor (RRF) and shear effects on the well injectivity. Additionally, a comprehensive assisted history match method and robust simulation sensitivity analysis was implemented, thousands of sensitivity simulation runs were performed to capture several possible injection scenarios and validate laboratory parameters. The simulation study confirmed that the PIT could be interpreted using the laboratory-measured polymer parameters such as polymer bulk viscosity, in-situ rheology, RRF and adsorption.


2018 ◽  
Vol 91 (2) ◽  
pp. 1344-1352 ◽  
Author(s):  
Hongmei Deng ◽  
Mengting Luo ◽  
Xinyao Shi ◽  
Paul N. Williams ◽  
Kexin Li ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document