EFFECT OF PORE FLUIDS ON THE ELASTIC PROPERTIES OF SANDSTONE

Geophysics ◽  
1960 ◽  
Vol 25 (2) ◽  
pp. 433-444 ◽  
Author(s):  
R. L. Mann ◽  
I. Fatt
Keyword(s):  
Young’S Modulus ◽  
Elastic Properties ◽  
Poisson’S Ratio ◽  
Elastic Moduli ◽  
Young's Modulus ◽  
Clay Content ◽  
Poisson's Ratio ◽  
Statistical Validity ◽  
Bulk Compressibility ◽  
Water Saturated

Bulk compressibility, Young’s modulus, and Poisson’s ratio were measured on three sandstones. Measurements were made on both dry and water saturated samples. Several runs were made on each sandstone to establish the statistical validity of the differences observed between the wet and dry samples. Bulk compressibility of wet sandstone was 10 to 30 percent greater than for dry. Young’s modulus was 8 to 20 percent less for wet sandstone, and Poisson’s ratio was 100 percent greater on one type of sandstone when wet and only slightly greater or about the same on wet samples of the others. A high clay content is believed to lead to a large effect of water on the elastic moduli of sandstone.

Experimental investigation of the effects of clay content and compaction stress on the elastic properties and anisotropy of dry and saturated synthetic shale

Geophysics ◽  
2018 ◽  
Vol 83 (5) ◽  
pp. C195-C208 ◽  
Author(s):  
Fei Gong ◽  
Bangrang Di ◽  
Jianxin Wei ◽  
Pinbo Ding ◽  
He Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Elastic Properties ◽  
Poisson’S Ratio ◽  
Symmetry Axis ◽  
Young's Modulus ◽  
Clay Content ◽  
Mechanical Anisotropy ◽  
Poisson's Ratio ◽  
Compaction Stress

Anisotropy in shales is an important issue in exploration and reservoir geophysics, and it has been proven extremely difficult to correlate anisotropy in natural shale by means of a single variable (in this case, clay content or compaction stress) because of the influence of multiple factors, such as water content, total organic carbon content, and complex mineral compositions. Thus, we used quartz, kaolinite, calcite, and kerogen extract as the primary materials to construct two sets of synthetic shale samples, each with a different clay content by weight and a different compaction stress. Ultrasonic experiments were conducted to investigate the anisotropy of velocity and mechanical properties in dry and saturated samples of our synthetic shales. The results reveal that the velocities decrease with clay content by weight and increase with compaction stress and that these changes are significant at low compaction stress. The velocity anisotropy of the samples increases with clay content and compaction stress due to the increasing alignment of the clay platelets. S-wave anisotropy is more sensitive to the clay content or compaction stress than P-wave anisotropy. The dynamic Young’s modulus [Formula: see text] of the samples decreases with clay content and increases with compaction stress, whereas Poisson’s ratio [Formula: see text] increases with clay content and decreases with compaction stress. Young’s modulus perpendicular to the symmetry axis is always larger than that parallel to the symmetry axis, but Poisson’s ratio perpendicular to the symmetry axis may be larger or smaller than that parallel to the symmetry axis, which indicates that mechanical properties have obvious anisotropic behavior. The elastic properties and anisotropy are also affected by fluids; the values of elastic and mechanical anisotropy parameters in saturated samples are significantly lower than those in dry samples.

scholarly journals Elastic Properties of Thulium Doped Zinc Borotellurite Glass

2016 ◽  
Vol 863 ◽  
pp. 70-74 ◽  
Author(s):  
Laoding Hasnimulyati ◽  
Mohamed Kamari Halimah ◽  
Zakaria Azmi ◽  
Abdul Halim Shaari ◽  
Mansor Ishak
Keyword(s):  
Young’S Modulus ◽  
Elastic Properties ◽  
Poisson’S Ratio ◽  
Elastic Moduli ◽  
Young's Modulus ◽  
Longitudinal Shear ◽  
Poisson's Ratio ◽  
Melt Quenching ◽  
Ultrasound Technique ◽  
Quenching Method

A series of Tm-doped zinc borotellurite glass have been extracted by conventional melt-quenching method. The density was measured and it had been found that the value is increased by the increment of Tm3+ ion. The elastic properties of the sample were determined by measuring longitudinal and shear velocities using an ultrasound technique. Then the values inserted into equations that calculate the elastic moduli of the glass samples. These include longitudinal, shear, bulk, Young’s modulus and also the Poisson’s ratio. The longitudinal and shear velocities show an increment as Tm3+ increases from 0.01 to 0.03 mol content. The trend then changes as Tm3+ increases from 0.03 to 0.05 mol content. In terms of elastic moduli, it produces a rapid increment with Tm3+ until 0.03 mol content. But after that, the increment becomes slow until 0.05 mol of Tm3+. The value of Poisson’s ratio decreases with the addition of Tm3+ concentration.

Evaluation of Effective Elastic Mechanical Properties of Graphene Sheets

2012 ◽  
Author(s):  
Khalid I. Alzebdeh
Keyword(s):  
Boundary Conditions ◽  
Young’S Modulus ◽  
Graphene Sheet ◽  
Poisson’S Ratio ◽  
Elastic Moduli ◽  
Young's Modulus ◽  
Unit Cell ◽  
Poisson's Ratio ◽  
Graphene Sheets ◽  
Numerical Predictions

The mechanical behaviour of a single-layer nanostructured graphene sheet is investigated using an atomistic-based continuum model. This is achieved by equating the stored energy in a representative unit cell for a graphene sheet at atomistic scale to the strain energy of an equivalent continuum medium under prescribed boundary conditions. Proper displacement-controlled (essential) boundary conditions which generate a uniform strain field in the unit cell model are applied to calculate one elastic modulus at a time. Three atomistic finite element models are adopted with an assumption that force interactions among carbon atoms can be modeled by either spring-like or beam elements. Thus, elastic moduli for graphene structure are determined based on the proposed modeling approach. Then, effective Young’s modulus and Poisson’s ratio are extracted from the set of calculated elastic moduli. Results of Young’s modulus obtained by employing the different atomistic models show a good agreement with the published theoretical and numerical predictions. However, Poisson’s ratio exhibits sensitivity to the considered atomistic model. This observation is supported by a significant variation in estimates as can be found in the literature. Furthermore, isotropic behaviour of in-plane graphene sheets was validated based on current modeling.

scholarly journals On the identification of the eggshell elastic properties under quasistatic compression

2004 ◽  
Vol 52 (5) ◽  
pp. 73-82 ◽  
Author(s):  
Jana Simeonovová ◽  
Jaroslav Buchar
Keyword(s):  
Young’S Modulus ◽  
Elastic Properties ◽  
Elastic Constants ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Poisson's Ratio ◽  
Rotational Shell ◽  
Mutual Comparison ◽  
Quasistatic Loading

The problem of the identification of the elastic properties of eggshell, i.e. the evaluation of the Young's modulus and Poisson's ratio is solved. The eggshell is considered as a rotational shell. The experiments on the egg compression under quasistatic loading have been conducted. During these experiments a strain on the eggshell surface has been recorded. By the mutual comparison between experimental and theoretical values of strains the influence of the elastic constants has been demonstrated.

scholarly journals Thermally Tunable Dynamic and Static Elastic Properties of Hydrogel Due to Volumetric Phase Transition

Polymers ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 1462 ◽  
Author(s):  
Yuqi Jin ◽  
Teng Yang ◽  
Shuai Ju ◽  
Haifeng Zhang ◽  
Tae-Youl Choi ◽  
...  
Keyword(s):  
Phase Transition ◽  
Bulk Modulus ◽  
Young’S Modulus ◽  
Elastic Properties ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Poisson's Ratio ◽  
Solution Temperature ◽  
Temperature Sensitive ◽  
Alginate Hydrogel

The temperature dependence of the mechanical properties of polyvinyl alcohol-based poly n-isopropyl acrylamide (PVA-PNIPAm) hydrogel was studied from the static and dynamic bulk modulus of the material. The effect of the temperature-induced volumetric phase transition on Young’s Modulus, Poisson’s ratio, and the density of PVA-PNIPAm was experimentally measured and compared with a non-thermo-responsive Alginate hydrogel as a reference. An increase in the temperature from 27.5 to 32 °C results in the conventional temperature-dependent de-swelling of the PVA-PNIPAm hydrogel volume of up to 70% at the lower critical solution temperature (LCST). However, with the increase in temperature, the PVA-PNIPAm hydrogel showed a drastic increase in Young’s Modulus and density of PVA-PNIPAm and a corresponding decrease in the Poisson’s ratio and the static bulk modulus around the LCST temperature. The dynamic bulk modulus of the PVA-PNIPAm hydrogel is highly frequency-dependent before the LCST and highly temperature-sensitive after the LCST. The dynamic elastic properties of the thermo-responsive PVA-PNIPAm hydrogel were compared and observed to be significantly different from the thermally insensitive Alginate hydrogel.

scholarly journals Effects of Pressurizing Cryogenic Treatments on Physical and Mechanical Properties of Shale Core Samples—An Experimental Study

Gases ◽  
2021 ◽  
Vol 1 (1) ◽  
pp. 33-50
Author(s):  
Rayan Khalil ◽  
Hossein Emadi ◽  
Faisal Altawati
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Cryogenic Treatment ◽  
Poisson's Ratio ◽  
The Core ◽  
Core Samples ◽  
Bulk Compressibility ◽  
Core Holder

The technique of cryogenic treatments requires injecting extremely cold fluids such as liquid nitrogen (LN2) into formations to create fractures in addition to connecting pre-existing fracture networks. This study investigated the effects of implementing and pressurizing cryogenic treatment on the physical (porosity and permeability) and mechanical properties (Young’s modulus, Poisson’s ratio, and bulk compressibility) of the Marcellus shale samples. Ten Marcellus core samples were inserted in a core holder and heated to 66 °C using an oven. Then, LN2 (−177 °C) was injected into the samples at approximately 0.14 MPa. Nitrogen was used to pressurize nine samples at injection pressures of 1.38, 2.76, and 4.14 MPa while the tenth core sample was not pressurized. Using a cryogenic pressure transducer and a T-type thermocouple, the pressure and temperature of the core holder were monitored and recorded during the test. The core samples were scanned using a computed tomography (CT) scanner, and their porosities, permeability, and ultrasonic velocities were measured both before and after conducting the cryogenic treatments. The analyses of CT scan results illustrated that conducting cryogenic treatments created new cracks inside all the samples. These cracks increased the pore volume, and as a result, the porosity, permeability, and bulk compressibility of the core samples increased. The creations of the new cracks also resulted in reductions in the compressional and shear velocities of the samples, and as a result, decreasing the Young’s modulus and Poisson’s ratio. Moreover, the results revealed that pressurizing the injected LN2 increased the alterations of aforementioned properties.

Elastic moduli of boron nitride, aluminium nitride and gallium nitride nanotubes using second generation reactive empirical bond order potential

2015 ◽  
Vol 11 (1) ◽  
pp. 2-15 ◽  
Author(s):  
Dinesh Kumar ◽  
Veena Verma ◽  
Keya Dharamvir ◽  
H S Bhatti
Keyword(s):  
Shear Modulus ◽  
Young’S Modulus ◽  
Elastic Properties ◽  
Poisson’S Ratio ◽  
Second Generation ◽  
Young's Modulus ◽  
Poisson's Ratio ◽  
Content Type ◽  
Bond Order Potential ◽  
Rebo Potential

Purpose – The purpose of this paper is to study elastic properties of III-V nitride nanotubes (NNTs) using second generation (REBO) potential. Design/methodology/approach – In the present research paper elastic properties of BN, AlN and GaN nanotubes have been investigated, using the second generation REBO potential by Brenner and co-workers, which is a bond order potential earlier used for carbon nanostructures successfully. In the present calculation, the same form of potential is used with adjusted parameters for h-BN, h-AlN and h-GaN. In all these cases the authors have considered graphite like network and strongly polar nature of these atoms so electrostatic forces are expected to play an important role in determining elastic properties of these nanotubes. The authors generate the coordinates of nanotubes of different chirality’s and size. Each and every structure thus generated is allowed to relax till the authors obtain minima of energy. The authors then apply the requisite compressions, elongations and twists to the structures and compute the elastic moduli. Young’s Modulus, Shear Modulus and Poisson’s ratio for single-walled armchair and zigzag tubes of different chirality’s and size have been calculated. The computational results show the variation of Young’s Modulus, Poisson’s ratio and Shear Modulus for these NNTs with nanotube diameter. The results have been compared with available data, experimental as well as theoretical. Findings – The authors have calculated bond length, cohesive energy/bond, Strain energy, Young’s Modulus, Shear Modulus and Poisson’s ratio. Originality/value – To the best of the knowledge this work is the first attempt to study elastic properties of III-V NNTs using second generation REBO potential

scholarly journals Discrepancy between measured dynamic poroelastic parameters and predicted values from Wyllie’s equation for water-saturated Istebna sandstone

2021 ◽  
Author(s):  
Dariusz Knez ◽  
Herimitsinjo Rajaoalison
Keyword(s):  
Young’S Modulus ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Laboratory Data ◽  
Confining Pressure ◽  
P Wave ◽  
Poisson's Ratio ◽  
Rock Properties ◽  
Biot’S Coefficient ◽  
Water Saturated

AbstractThe drilling-related geomechanics requires a better understanding of the encountered formation properties such as poroelastic parameters. This paper shows set of laboratory results of the dynamic Young’s modulus, Poisson’s ratio, and Biot’s coefficient for dry and water-saturated Istebna sandstone samples under a series of confining pressure conditions at two different temperatures. The predicted results from Wyllie’s equation were compared to the measured ones in order to show the effect of saturation on the rock weakening. A negative correlation has been identified between Poisson’s ratio, Biot’s coefficient and confining pressure, while a positive correlation between confining pressure and Young’s modulus. The predicted dynamic poroelastic rock properties using the P-wave value from Wyllie’s equation are different from measured ones. It shows the important influence of water saturation on rock strength, which is confirmed by unconfined compressive strength measurement. Linear equations have been fitted for the laboratory data and are useful for the analysis of coupled stress and pore pressure effects in geomechanical problems. Such results are useful for many drilling applications especially in evaluation of such cases as wellbore instability and many other drilling problems.

SONIC DETERMINATION OF THE ELASTIC PROPERTIES OF ICE

1947 ◽  
Vol 25a (2) ◽  
pp. 88-95 ◽  
Author(s):  
T. D. Northwood
Keyword(s):  
Rayleigh Wave ◽  
Young’S Modulus ◽  
Elastic Properties ◽  
Elastic Waves ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
The Other ◽  
Poisson's Ratio ◽  
Wave Velocities

By measuring the velocity of various types of elastic waves in a solid it is possible to deduce Young's modulus and Poisson's ratio. Longitudinal, extensional, and Rayleigh wave velocities were measured in ice, the first by resonance in a rod and the other two by a pulsing technique. The value obtained for Young's modulus was 9.8 × 1010 dynes per cm.2 and for Poisson's ratio was 0.33.

Sign in / Sign up

Export Citation Format

Share Document