Surface hardness methods

2006 ◽  
pp. 48-62
Keyword(s):  
Surface Hardness

Effect of silver nitrate on some mechanical properties of heat polymerizing acrylic resins

2019 ◽  
Vol 14 (1) ◽  
pp. 110
Author(s):  
Assiss. Prof. Dr. Sabiha Mahdi Mahdi ◽  
Dr. Firas Abd K. Abd K.
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Silver Nitrate ◽  
Surface Hardness ◽  
Mechanical Tests ◽  
Hardness Tester ◽  
Acrylic Resins ◽  
The Difference

Aim: The aimed study was to evaluate the influence of silver nitrate on surfacehardness and tensile strength of acrylic resins.Materials and methods: A total of 60 specimens were made from heat polymerizingresins. Two mechanical tests were utilized (surface hardness and tensile strength)and 4 experimental groups according to the concentration of silver nitrate used.The specimens without the use of silver nitrate were considered as control. Fortensile strength, all specimens were subjected to force till fracture. For surfacehardness, the specimens were tested via a durometer hardness tester. Allspecimens data were analyzed via ANOVA and Tukey tests.Results: The addition of silver nitrate to acrylic resins reduced significantly thetensile strength. Statistically, highly significant differences were found among allgroups (P≤0.001). Also, the difference between control and experimental groupswas highly significant (P≤0.001). For surface hardness, the silver nitrate improvedthe surface hardness of acrylics. Highly significant differences were statisticallyobserved between control and 900 ppm group (P≤0.001); and among all groups(P≤0.001)with exception that no significant differences between control and150ppm; and between 150ppm and 900ppm groups(P>0.05).Conclusion: The addition of silver nitrate to acrylics reduced significantly the tensilestrength and improved slightly the surface hardness.

Effect of light intensity and water aging on surface hardness of dental resin-composites

2019 ◽  
Vol 64 (11) ◽  
pp. 1007-1014
Author(s):  
Tong XU ◽  
◽  
Jia-Hui ZHANG ◽  
Zhao-Ying LIU ◽  
Xuan LI ◽  
...  
Keyword(s):  
Light Intensity ◽  
Surface Hardness ◽  
Resin Composites ◽  
Dental Resin ◽  
Dental Resin Composites ◽  
Effect Of Light

Severe plastic deformation of Al-1%Cu Alloy processed by a Simple Cyclic Extrusion Compression technique

2018 ◽  
Vol 1 (1) ◽  
pp. 77-90
Author(s):  
Walaa Abdelaziem ◽  
Atef Hamada ◽  
Mohsen A. Hassan
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Deformation Behavior ◽  
Cast Alloy ◽  
Surface Hardness ◽  
Grain Structure ◽  
Compression Technique ◽  
Cu Alloy ◽  
Cyclic Extrusion Compression

Severe plastic deformation is an effective method for improving the mechanical properties of metallic alloys through promoting the grain structure. In the present work, simple cyclic extrusion compression technique (SCEC) has been developed for producing a fine structure of cast Al-1 wt. % Cu alloy and consequently enhancing the mechanical properties of the studied alloy. It was found that the grain structure was significantly reduced from 1500 µm to 100 µm after two passes of cyclic extrusion. The ultimate tensile strength and elongation to failure of the as-cast alloy were 110 MPa and 12 %, respectively. However, the corresponding mechanical properties of the two pass CEC deformed alloy are 275 MPa and 35%, respectively. These findings ensure that a significant improvement in the grain structure has been achieved. Also, cyclic extrusion deformation increased the surface hardness of the alloy by 49 % after two passes. FE-simulation model was adopted to simulate the deformation behavior of the material during the cyclic extrusion process using DEFORMTM-3D Ver11.0. The FE-results revealed that SCEC technique was able to impose severe plastic strains with the number of passes. The model was able to predict the damage, punch load, back pressure, and deformation behavior.

DILLIDUR 450V

Alloy Digest ◽  
2011 ◽  
Vol 60 (12) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Room Temperature ◽  
Surface Hardness ◽  
Heat Treating ◽  
Hot Working ◽  
Resistant Steel ◽  
Bend Strength

Abstract Dillidur 450V is a water hardened wear-resistant steel with surface hardness at room temperature of 420-480 HB. The steel is easy to weld and bend. Hot working is not recommended. This datasheet provides information on composition, physical properties, hardness, tensile properties, and bend strength as well as fracture toughness. It also includes information on wear resistance as well as forming, heat treating, machining, and joining. Filing Code: SA-638. Producer or source: Dillinger Hütte GTS.

NITRODUR 8524

Alloy Digest ◽  
2017 ◽  
Vol 66 (12) ◽  
Keyword(s):  
Fracture Toughness ◽  
Fatigue Strength ◽  
Tensile Properties ◽  
High Temperatures ◽  
High Surface ◽  
Surface Hardness ◽  
Operating Temperatures

Abstract NITRODUR 8524 (8CrMo16, 1.8524) is one of the Nitrodur family of nitriding steels that are used where high surface hardness and good fatigue strength are required and the material is also subjected to high temperatures. Nitrided surfaces maintain their hardness and strength at operating temperatures of up to approximately 500–550 deg C (932–1022 deg F). This datasheet provides information on composition, hardness, and tensile properties as well as fracture toughness. It also includes information on surface qualities as well as casting and forming. Filing Code: SA-807. Producer or source: Schmolz + Bickenbach Group.

LUKENS HARDWEAR 500

Alloy Digest ◽  
1994 ◽  
Vol 43 (4) ◽  
Keyword(s):  
Alloy Steel ◽  
Surface Hardness ◽  
Steel Company ◽  
Resistant Alloy

Abstract LUKENS HARDWEAR 500 is a premium abrasion resistant alloy steel with improved forming and welding characteristics. Typical surface hardness range (BHN) of 477-520, depending on thickness. This datasheet provides information on composition and hardness. It also includes information on forming and joining. Filing Code: SA-472. Producer or source: Lukens Steel Company.

LUKENS HARDWEAR 425

Alloy Digest ◽  
1994 ◽  
Vol 43 (3) ◽  
Keyword(s):  
Alloy Steel ◽  
Surface Hardness ◽  
Steel Company ◽  
Resistant Alloy

Abstract LUKENS HARDWEAR 425 is a premium abrasion resistant alloy steel with improved forming and welding characteristics. Typical surface hardness range (BHN) is 400-444, depending on thickness. This datasheet provides information on composition and hardness. It also includes information on forming and joining. Filing Code: SA-471. Producer or source: Lukens Steel Company.

LUKENS HARDWEAR 400

Alloy Digest ◽  
1994 ◽  
Vol 43 (2) ◽  
Keyword(s):  
Alloy Steel ◽  
Surface Hardness ◽  
Steel Company ◽  
Resistant Alloy

Abstract LUKENS HARDWEAR 400 is a premium abrasion resistant alloy steel with improved forming and welding characteristics. Typical surface hardness range (BHN) of 321-444, depending on thickness. This datasheet provides information on composition and hardness. It also includes information on forming and joining. Filing Code: SA-470. Producer or source: Lukens Steel Company.

DEUTSCHE EDELSTAHLWERKE CRYODUR 2067

Alloy Digest ◽  
2020 ◽  
Vol 69 (2) ◽  
Keyword(s):  
Cold Work ◽  
High Surface ◽  
Surface Hardness ◽  
Heat Treating ◽  
Chromium Alloy ◽  
Dimensional Changes ◽  
Short Run ◽  
Quench Hardening ◽  
Specialty Steel ◽  
Cold Work Tool Steel

Abstract Deutsche Edelstahlwerke Cryodur 2067 is a high-carbon, 1.5% chromium, alloy cold-work tool steel. In view of its higher hardenability than that of the non-alloy, water-hardening, cold work tool steels, this steel can be oil quenched, a factor that minimizes dimensional changes during quench hardening. Cryodur 2067 is suitable for short run tooling in applications requiring high surface hardness. This datasheet provides information on composition, physical properties, hardness, and elasticity. It also includes information on forming, heat treating, and machining. Filing Code: TS-786. Producer or source: Deutsche Edelstahlwerke Specialty Steel.

Sign in / Sign up

Export Citation Format

Share Document