scholarly journals The Study on Dynamic Response Mechanism of TRIP Steel in the Highest Strain Rate

2015 ◽  
Vol 05 (06) ◽  
pp. 227-234
Author(s):  
巍 陈
2007 ◽  
Vol 340-341 ◽  
pp. 283-288 ◽  
Author(s):  
Jung Han Song ◽  
Hoon Huh

The dynamic response of the turbine blade materials is indispensable for analysis of erosions of turbine blades as a result of impulsive loading associated with gas flow. This paper is concerned with the dynamic material properties of the Inconel 718 alloy which is widely used in the high speed turbine blade. The dynamic response at the corresponding level of the strain rate should be acquired with an adequate experimental technique and apparatus due to the inertia effect and the stress wave propagation. In this paper, the dynamic response of the Inconel 718 at the intermediate strain rate ranged from 1/s to 400/s is obtained from the high speed tensile test and that at the high strain rate above 1000/s is obtained from the split Hopkinson pressure bar test. The effects of the strain rate on the dynamic flow stress, the strain rate sensitivity and the failure elongation are evaluated with the experimental results. Experimental results from both the quasi-static and the high strain rate up to 3000/s are interpolated in order to construct the constitutive relation that should be applied to simulate the dynamic behavior of the turbine blade made of the Inconel 718.


BMC Genomics ◽  
2021 ◽  
Vol 22 (1) ◽  
Author(s):  
Xiaojie Liu ◽  
Xiaoshuang Li ◽  
Xuejing Wen ◽  
Yan Zhang ◽  
Yu Ding ◽  
...  

Abstract Background Valsa canker is a serious disease in the stem of Malus sieversii, caused by Valsa mali. However, little is known about the global response mechanism in M. sieversii to V. mali infection. Results Phytohormone jasmonic acid (JA) and salicylic acid (SA) profiles and transcriptome analysis were used to elaborate on the dynamic response mechanism. We determined that the JA was initially produced to respond to the necrotrophic pathogen V. mali infection at the early response stage, then get synergistically transduced with SA to respond at the late response stage. Furthermore, we adopted Pacific Biosciences (PacBio) full-length sequencing to identify differentially expressed transcripts (DETs) during the canker response stage. We obtained 52,538 full-length transcripts, of which 8139 were DETs. Total 1336 lncRNAs, 23,737 alternative polyadenylation (APA) sites and 3780 putative transcription factors (TFs) were identified. Additionally, functional annotation analysis of DETs indicated that the wild apple response to the infection of V. mali involves plant-pathogen interaction, plant hormone signal transduction, flavonoid biosynthesis, and phenylpropanoid biosynthesis. The co-expression network of the differentially expressed TFs revealed 264 candidate TF transcripts. Among these candidates, the WRKY family was the most abundant. The MsWRKY7 and MsWRKY33 were highly correlated at the early response stage, and MsWRKY6, MsWRKY7, MsWRKY19, MsWRKY33, MsWRKY40, MsWRKY45, MsWRKY51, MsWRKY61, MsWRKY75 were highly correlated at the late stage. Conclusions The full-length transcriptomic analysis revealed a series of immune responsive events in M. sieversii in response to V. mali infection. The phytohormone signal pathway regulatory played an important role in the response stage. Additionally, the enriched disease resistance pathways and differentially expressed TFs dynamics collectively contributed to the immune response. This study provides valuable insights into a dynamic response in M. sieversii upon the necrotrophic pathogen V. mali infection, facilitates understanding of response mechanisms to canker disease for apple, and provides supports in the identification of potential resistance genes in M. sieversii.


2015 ◽  
Vol 825-826 ◽  
pp. 182-188 ◽  
Author(s):  
Lutz Krüger ◽  
Steffen Grützner ◽  
Sabine Decker ◽  
Ines Schneider

Composite materials, which consist of a metastable austenitic TRIP-steel matrix (CrMnNi TRIPsteel; TRansformation Induced Plasticity) reinforced by alumina particles (25 vol.% ceramic, designated as AT 25/75) and reinforced by alumina and MgO partially stabilized zirconia particles (Mg-PSZ) (35 vol.% ceramic, designated as AT 25/75 + MgPSZ) were synthesized through spark plasma sintering (SPS). In the AT 25/75 + MgPSZ, the steel particles were mainly surrounded by alumina. Hence, mostly steel/alumina and alumina/MgPSZ interfaces existed. The mechanical behavior of the as-sintered samples was characterized by compression tests at room temperature and 40 °C and in a range of strain rates between 103s-1and 103s1. The influence of the ceramic content, strain rate and temperature on TRIP-effect of the steel matrix was investigated. Due to the increasing ceramic volume fraction, AT 25/75 + MgPSZ exhibits the highest compressive yield strength under all loading conditions and no strain rate sensitivity. This composite showed no measurable TRIP-effect, due to the low fracture strain. The deformation-induced α’martensite within the steel particles in pure steel and AT 25/75 primary depends on the testing temperature and the strain rate. This is attributed to an increase of stacking fault energy with rising temperature. High strain rates cause adiabatic heating, counteracting the martensitic transformation.


2007 ◽  
Vol 40 (1) ◽  
pp. 101-107 ◽  
Author(s):  
W.J. Dan ◽  
W.G. Zhang ◽  
S.H. Li ◽  
Z.Q. Lin

2016 ◽  
Vol 88 ◽  
pp. 44-54 ◽  
Author(s):  
Veera M. Boddu ◽  
Matthew W. Brenner ◽  
Jignesh S. Patel ◽  
Ashok Kumar ◽  
P. Raju Mantena ◽  
...  

Author(s):  
Richard Villavicencio ◽  
Young-Hun Kim ◽  
Sang-Rai Cho ◽  
C. Guedes Soares

Numerical simulations are presented, on the dynamic response of a one-tenth scaled tanker double hull structure struck laterally by a knife edge indenter. The small stiffeners of the full-scale prototype are smeared in the small-scale model by increasing the thicknesses of the corresponding plates. The dynamic response is evaluated at an impact velocity of 7.22 m/s and the impact point is chosen between two frames to assure damage to the outer shell plating and stringers. The simulations are performed by LS-DYNA finite element solver. They aim at evaluating the influence of strain hardening and strain rate hardening on the global impact response of the structure, following different models proposed in the literature. Moreover, the numerical model is scaled to its full-scale prototype, summarizing the governing scaling laws for collision analysis and evaluating the effect of the material strain rate on the plastic response of large scaled numerical models.


Sign in / Sign up

Export Citation Format

Share Document