Effects of Surface Roughness and Free Energy on Oral Bacterial Adhesion

2003 ◽  
pp. 91-102 ◽  
Author(s):  
Marc Quirynen ◽  
Kurt Dierickx ◽  
Daniel van Steenberghe
2021 ◽  
pp. 096739112110055
Author(s):  
Gunce Ozan ◽  
Meltem Mert Eren ◽  
Cansu Vatansever ◽  
Ugur Erdemir

Surface sealants are reported to ensure surface smoothness and improve the surface quality of composite restorations. These sealants should also reduce the bacterial adhesion on composite surfaces however, there is not much information regarding their performance on bulk-fill composite materials. The aim of this study was to evaluate the effect of surface sealant application on surface roughness and bacterial adhesion of various restorative materials. Disc-shaped samples were prepared from a compomer, a conventional composite and three bulk-fill composites. Specimens of each group were divided into two groups (n = 9): with/without surface sealant (Biscover LV, [BLV]). Surface roughness values were examined by profilometry and two samples of each group were examined for bacterial adhesion on a confocal laser scanning microscope (CLSM). Bacterial counts were calculated by both broth cultivation and microscopic images. Results were analyzed with one-way ANOVA and Bonferroni/Dunn tests. Following the BLV application, there was a decrease in the surface roughness values of all groups however, only Tetric N-Ceram Bulk and Beautifil-Bulk groups showed significantly smoother surfaces (p < 0.001). There were no significant differences among material groups without BLV application. Evaluating bacterial adhesion after BLV application, conventional composite had the lowest values among all followed by the compomer group. Beautifil-Bulk had significantly the highest bacterial adhesion (p < 0.05), followed by Tetric N-Ceram Bulk group. Without BLV application, there was no significant difference among bacterial adhesion values of groups (p > 0.05). CLSM images showed cell viability in groups. Bulk-fill composites showed higher bacterial adhesion than conventional composite and compomer materials. The surface sealant was found to be highly effective in lowering bacterial adhesion, but not so superior in smoothing the surfaces of restorative materials. So, surface sealants could be used on the restorations of patients with high caries risk.


Molecules ◽  
2021 ◽  
Vol 26 (4) ◽  
pp. 900
Author(s):  
Maria Vardaki ◽  
Aida Pantazi ◽  
Ioana Demetrescu ◽  
Marius Enachescu

In this work we present the results of a functional properties assessment via Atomic Force Microscopy (AFM)-based surface morphology, surface roughness, nano-scratch tests and adhesion force maps of TiZr-based nanotubular structures. The nanostructures have been electrochemically prepared in a glycerin + 15 vol.% H2O + 0.2 M NH4F electrolyte. The AFM topography images confirmed the successful preparation of the nanotubular coatings. The Root Mean Square (RMS) and average (Ra) roughness parameters increased after anodizing, while the mean adhesion force value decreased. The prepared nanocoatings exhibited a smaller mean scratch hardness value compared to the un-coated TiZr. However, the mean hardness (H) values of the coatings highlight their potential in having reliable mechanical resistances, which along with the significant increase of the surface roughness parameters, which could help in improving the osseointegration, and also with the important decrease of the mean adhesion force, which could lead to a reduction in bacterial adhesion, are providing the nanostructures with a great potential to be used as a better alternative for Ti implants in dentistry.


2019 ◽  
Vol 38 (2) ◽  
pp. 311-316 ◽  
Author(s):  
Hanho GO ◽  
Howon PARK ◽  
Juhyun LEE ◽  
Hyunwoo SEO ◽  
Siyoung LEE

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Khaled S. Al-Athel ◽  
Najat Marraiki ◽  
Abul Fazal M. Arif ◽  
Syed Sohail Akhtar ◽  
Javad Mostaghimi ◽  
...  

In this work, 316L stainless steel samples were coated with copper (Cu) and German silver (Cu 17%Ni 10%Zn) to investigate the relation between their mechanical and antibacterial behaviors. The mechanical and material characteristics of the samples were studied by looking into the microstructure of the surface and the cross-section of the coatings, the surface roughness, and the adhesion strength between the coating layer and the substrate. The antibacterial behavior is then studied against gram-negative Escherichia coli and gram-positive Staphylococcus aureus. Two experiments were conducted to examine the antibacterial behavior. In the first experiment, the coated samples were covered with distilled water, whereas in the second experiment, the samples were tested without being covered with distilled water. The results show that German silver (Cu 17%Ni 10%Zn) had a higher antibacterial rate than copper (Cu) by around 10% for both gram-negative E. coli and gram-positive S. aureus. The reason is because a smoother surface is expected to limit the bacterial adhesion in most cases, and the German silver samples have a lower surface roughness (Ra) due to the higher thermal expansion value of zinc (Zn) compared with copper (Cu). A more in-depth look into the effect of various thickness of the coating with alloying elements (in this case nickel and zinc) on the antibacterial rate would be of great interest.


2014 ◽  
Vol 55 (5) ◽  
pp. 646 ◽  
Author(s):  
Yong Woo Ji ◽  
Soon Ho Hong ◽  
Dong Yong Chung ◽  
Eung Kweon Kim ◽  
Hyung Keun Lee

2010 ◽  
Vol 1277 ◽  
Author(s):  
Argelia Almaguer-Flores ◽  
Yolloxóchilt R. Sánchez-Cruz ◽  
Jung Hwa Park ◽  
René Olivares-Navarrete ◽  
Michel Dard ◽  
...  

Micron-scale and submicron-scale surface roughness enhance osteoblast differentiation on titanium (Ti) substrates and increases bone-to-implant contact in vivo. However, bacterial adhesion is also strongly influenced by roughness and surface chemistry. The aim of this study was to investigate if chemical surface modifications alter initial bacterial attachment. To achieve this, two polyelectrolyte layers [chitosan (Ch) and poly(L-lysine) (PLL)] were used to coat Ti surfaces with different roughness (PT [Ra<0.3μm], SLA [Ra≥3.0μm]). Bacterial attachment was evaluated using Aggregatibacter actinomycetemcomitans, Actinomyces israelii, Campylobacter rectus, Eikenella corrodens, Fusobacterium nucleatum, Parvimonas micra, Porphyromonas gingivalis, Prevotella intermedia and Streptococcus sanguinis. After 24h incubation, bacteria were detached from the samples with sonication and the counting plate technique was performed to determine the number of colony forming units (CFU's). Additionally, surfaces were observed by scanning electron microscopy to determine bacteria surface coverage. Statistical significance was determined using ANOVA followed by Bonferroni's modification of Student's t-test. The results showed that polyelectrolyte coatings did not affect surface roughness. Modified surfaces were more hydrophilic than the controls. PT surfaces covered by Chi exhibited lower CFUs than the same surface covered by PLL or the control PT (140 × 105/mL, 343 × 105/mL and 283 × 105/mL, respectively). The opposite effect was observed on the SLA surfaces, PLL coated samples shown lower CFUʼs than Chi or uncoated SLA (199 × 105/mL, 229 × 105/mL and 227 × 105/mL, respectively). The Chi layer appeared to reduce bacterial adhesion only on the smooth surfaces. In contrast, PLL coatings reduced bacterial attachment on rougher surfaces. These results suggest that chemical modification of Ti without alteration of surface roughness affects oral bacterial attachment, and could be useful to prevent peri-implantitis related diseases.


1990 ◽  
Vol 17 (3) ◽  
pp. 138-144 ◽  
Author(s):  
M. Quirynen ◽  
M. Marechal ◽  
H. J. Busscher ◽  
A. H. Weerkamp ◽  
P. L. Darius ◽  
...  

Biomaterials ◽  
2010 ◽  
Vol 31 (13) ◽  
pp. 3674-3683 ◽  
Author(s):  
Vi K. Truong ◽  
Rimma Lapovok ◽  
Yuri S. Estrin ◽  
Stuart Rundell ◽  
James Y. Wang ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document