scholarly journals Excitation Analysis of Transverse Electric Mode Rectangular Waveguide

2020 ◽  
Vol 20 (1) ◽  
pp. 1
Author(s):  
M. Reza Hidayat ◽  
Mohamad Hamzah Zamzam ◽  
Salita Ulitia Prini
Keyword(s):  
Insertion Loss ◽  
Rectangular Waveguide ◽  
Electromagnetic Waves ◽  
Return Loss ◽  
Bandpass Filter ◽  
Frequency Range ◽  
A Value ◽  
Observation Process ◽  
Wireless Broadband ◽  
Loss Parameter

A waveguide is a transmission medium in the form of a pipe and is made from a single conductor. A waveguide has the function of delivering electromagnetic waves with a frequency of 300 MHz - 300 GHz and is able to direct the waves in a particular direction. In its development, a waveguide can be used as a filter. A filter consists of several circuits designed to pass signals that are generated at a specific frequency and attenuate undesired signals. One type of filter that can pass a signal in a particular frequency range and block signals that are not included in that frequency range is a bandpass filter. In this article, we study a rationing analysis on rectangular waveguide using TEmn mode followed by an implementation of a bandpass filter in the frequency range of 3.3-3.5 GHz for S-Band Wireless Broadband and Fixed Satellite. The observation process is done by shifting the position of the connector (power supply) as much as five times the shift to get the results as desired. Based on the analysis of the simulation process using Ansoft HFSS software, it is observed that the optimized results of the rectangular waveguide mode TE10 were obtained at a distance between connectors of 30 mm with a cut-off frequency of 3.3 GHz, the value of the return loss parameter of -34.442 dB and an insertion loss of -0.039 dB. Whereas, the optimized TE20 mode can be obtained at a distance of 70 mm between connectors, with a cut-off frequency of 3.5 GHz, the value of the return loss parameter of -28.718 dB and an insertion loss of -0.045. The measurement of TE10 mode in our Vector Network Analyzer (VNA) shows a cut-off frequency of 3.2 GHz, with a value of the return loss of -18.73 dB and an insertion loss of -2.70 dB. Meanwhile, a measurement of TE20 mode results in a cut-off frequency of 3.2 GHz, with a value of the return loss of -5.89 dB and an insertion loss of -4.31 dB.

scholarly journals Design of microstrip hairpin bandpass filter for 2.9 GHz – 3.1 GHz s-band radar with defected ground structure

2019 ◽  
Vol 14 (4) ◽  
pp. 448-455 ◽  
Author(s):  
Nanang Ismail ◽  
Teddy Surya Gunawan ◽  
Santi Kartika S ◽  
Teguh Praludi ◽  
Eki A.Z. Hamidi
Keyword(s):  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Filter Design ◽  
Center Frequency ◽  
Small Displacement ◽  
Substrate Thickness ◽  
Frequency Range ◽  
Defected Ground Structure ◽  
Ground Structure

Radar has been widely used in many fields, such as telecommunication, military applications, and navigation. The filter is one of the most important parts of a radar system, in which it selects the necessary frequency and blocks others. This paper presents a novel yet simple filter design for S-band radar in the frequency range of 2.9 to 3.1 GHz. The center frequency of the filter was designed at 3 GHz with a bandwidth of 200 MHz, insertion loss larger than -3 dB and return loss less than -20 dB. Fifth order microstrip hairpin bandpass filter (BPF) was designed and implemented on Rogers 4350B substrate which has a dielectric relative constant value of (εr)= 3.48 and substrate thickness of (h) =1.524 mm. One element of the square groove was added as Defected Ground Structure (DGS) which can decrease the filter size, reduce harmonization, and increase return loss. Two scenarios were used in the measurement, i.e. with and without enclosed aluminum casing. Results showed that BPF without casing obtained the insertion loss of -1.748 dB at 2.785 GHz and return loss of -21.257 dB in the frequency range between 2.785 to 2.932 GHz. On the other hand, BPF with casing shows a better performance, in which it obtained the insertion loss of -1.643 dB at 2.921 GHz and return loss of -19.529 in the frequency range between 2.820 to 3.021 GHz. Although there is small displacement of frequency and response value between the simulation and implementation, our BPF has the ability to work on S-band radar with a frequency range of 2 to 4 GHz. 

scholarly journals Sharp Skirt Dual-Mode Bandpass Filter with Overlay Plate to Control Upper Passband Edge

2019 ◽  
Vol 8 (6) ◽  
pp. 2357-2360
Keyword(s):  
Analytical Model ◽  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Center Frequency ◽  
Dual Mode ◽  
Rf Receivers ◽  
Attenuation Level ◽  
Frequency Selective ◽  
Fixed Center

This paper presents design and analytical model for Sharp Skirt Dual-Mode Bandpass Filter for RF receivers. Proposed filter is designed using open stub loaded H shaped resonator. Based on analytical model insertion loss S21 and return loss S11 for proposed filter are demonstrated. Inductive Overlaying plate is proposed to control upper passband edge of proposed filter to improve frequency selectivity with fixed center frequency. The proposed filter has sharp frequency selective range from 5.1GHz to 9.2GHz. With overlay plate, frequency selective range is tuned to 5.1GHz-8.6GHz. Without overlaying plate the proposed filter has return loss greater than 10dB and insertion loss of 0.7dB. Lower and upper passband edges are at 5.1GHz and 9.2GHz with attenuation level of 52dB and 54dB respectively. With overlaying plate, the filter has same S 11 and S 21 parameters, but upper passband edge is shifted from 9.2GHz to 8.6GHz

scholarly journals Directivity Enhancement in Non-Reciprocal Bandpass Filters using an Evolutionary Algorithm

2021 ◽  
Author(s):  
Prantik Dutta ◽  
Arun Gande ◽  
Gopi Ram
Keyword(s):  
Evolutionary Algorithm ◽  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Trial And Error ◽  
Swarm Optimization ◽  
Lumped Element ◽  
Trial And Error Method ◽  
Error Method ◽  
Maximum Directivity

In this letter, a non-reciprocal filter with enhanced directivity is analyzed methodically and the filter parameters are optimized using an evolutionary algorithm. The return loss, insertion loss, and isolation characteristics of the filter exhibit a trade-off that makes manual tuning a trial-and-error method. The veracity of the numerical modeling is conformed by designing a 150 MHz lumped element non-reciprocal bandpass filter based on the parameters extracted using an evolutionary algorithm based particle swarm optimization (PSO). The simulated and measured results comply well with the modeling and the results exhibit maximum directivity of 28.2 dB without degradation in insertion loss (1.1 dB) and return loss (16.2 dB) within the passband. The algorithm can be utilized in designing non-reciprocal filters having different center frequencies and bandwidths.

scholarly journals A Simplified Design Inline Microstrip-to-Waveguide Transition

Electronics ◽  
2018 ◽  
Vol 7 (10) ◽  
pp. 215 ◽  
Author(s):  
José Pérez-Escudero ◽  
Alicia Torres-García ◽  
Ramón Gonzalo ◽  
Iñigo Ederra
Keyword(s):  
Insertion Loss ◽  
Rectangular Waveguide ◽  
Return Loss ◽  
Intermediate Step ◽  
Analytical Design ◽  
Waveguide Transition ◽  
W Band

A simplified design of an inline transition between microstrip and rectangular waveguide is presented in this paper. The transition makes use of a dielectric filled rectangular waveguide (DFRW) as an intermediate step, which simplifies manufacturing and allows for an analytical design. The behavior of the transition has been experimentally validated in the W-band by means of a back-to-back configuration. Good performance has been achieved: a return loss greaterthan 10 dB and mean insertion loss lower than 1 dB.

Compact transition from CBCPW to substrate integrated suspended line (SISL) for operation up to 46 GHz

2019 ◽  
Vol 12 (2) ◽  
pp. 116-119
Author(s):  
F. Parment ◽  
A. Ghiotto ◽  
T.-P. Vuong ◽  
L. Carpentier ◽  
K. Wu
Keyword(s):  
Insertion Loss ◽  
Return Loss ◽  
Coplanar Waveguide ◽  
Experimental Results ◽  
Frequency Range ◽  
Better Than

AbstractA compact transition between conductor-backed coplanar waveguide (CBCPW) and substrate integrated suspended line (SISL) is presented. Compared to the reported transitions from CBCPW to SISL, performance and compactness are improved. For demonstration purpose, a multilayer transition is designed and fabricated for operation up to 46 GHz. Experimental results, based on an electronic calibration and thru–reflect–line calibration allowing measurement in the 0.01–50 GHz frequency range, demonstrate an insertion loss of 0.59 ± 0.51 dB with a return loss of better than 10 dB in the 10 MHz to 46 GHz frequency range.

A wideband right-angle transition between thin substrate integrated waveguide and rectangular waveguide based on multi-section structure

2015 ◽  
Vol 8 (2) ◽  
pp. 185-191 ◽  
Author(s):  
Teng Li ◽  
Wenbin Dou
Keyword(s):  
Insertion Loss ◽  
Rectangular Waveguide ◽  
Return Loss ◽  
Impedance Matching ◽  
Experimental Results ◽  
Center Frequency ◽  
Substrate Integrated Waveguide ◽  
Rectangular Aperture ◽  
Section Structure ◽  
Better Than

In this paper, a novel wideband right-angle transition between thin substrate integrated waveguide (SIW) and rectangular waveguide (RWG) based on multi-section structure operating at center frequency 31.5 GHz is presented. A multi-section SIW with a rectangular aperture etched on the broad wall and two stepped ridges embedded in the RWG flange are introduced to obtain a wide impedance matching. The simulations show that the bandwidth with return loss better than 20 dB is about 17 GHz. In order to verify our designs, two back-to-back transitions with different lengths are fabricated and measured. The experimental results agree well with simulations. The proposed component shows an insertion loss less than 0.44 dB and a return loss better than 14.5 dB over 12.15 GH, which corresponds to 38.57% bandwidth.

A multi-mode resonator-based UWB bandpass filter with wide stopband

2015 ◽  
Vol 8 (7) ◽  
pp. 1031-1035 ◽  
Author(s):  
Ting Zhang ◽  
Fei Xiao ◽  
Xiaohong Tang ◽  
Lei Guo
Keyword(s):  
Return Loss ◽  
Bandpass Filter ◽  
Mode Analysis ◽  
Frequency Range ◽  
Coupled Line ◽  
Resonance Characteristic ◽  
Line Section ◽  
Multi Mode ◽  
Mode Resonator ◽  
Better Than

In this paper, a novel multi-mode resonator is presented, which is formed by cascading several open-circuited transmission line sections with a coupled-line section. Owing to its symmetry, even- and odd-mode analysis methods are applied to analyze its resonance characteristic. Based on this resonator, a microstrip ultra-wide bandwidth (UWB) bandpass filter is designed, fabricated, and measured. The simulated and measured results show that its bandwidth can cover the desired UWB. Return loss in passband is better than −14 dB. This filter is featured by good selectivity and wide stopband. Stopband suppression as low as −40 dB can be achieved within frequency range from 12 to 16 GHz.

Wide-stopband bandpass-filtering power divider with high-frequency selectivity

2017 ◽  
Vol 9 (10) ◽  
pp. 1931-1936 ◽  
Author(s):  
Kaijun Song ◽  
Yifang Zhou ◽  
Maoyu Fan ◽  
Yu Zhu ◽  
Yong Fan
Keyword(s):  
Insertion Loss ◽  
High Frequency ◽  
Return Loss ◽  
Signal Transmission ◽  
Frequency Selectivity ◽  
Power Divider ◽  
Center Frequency ◽  
Frequency Range ◽  
Transmission Zeros ◽  
Stopband Attenuation

A wide-stopband bandpass-filtering power divider with high-frequency selectivity has been proposed in this paper. The input and output feeding lines and eight 1/4 wavelength resonators are used to realize the signal transmission. In order to obtain good frequency selectivity, source-load coupling transmission path is used to generate transmission zeros near the passband. A four-way power divider with bandpass-filtering response and high-frequency selectivity is designed, fabricated, and measured. The measured results agree with the simulated ones closely in the desirable frequency range. The measured center frequency of the power divider is 2.38 GHz with input return loss of 31.2 dB, while the measured insertion loss is about 1 dB (not including ideal 6 dB four-way power dividing insertion loss). Moreover, the measured 3-dB bandwidth is 12% and the measured stopband attenuation is >15 dB from 2.59 to 7.7 GHz. In addition, two transmission zeros of 1.9 and 2.8 GHz are located near the passband. The measured output isolations are all >15.7 dB.

Investigation of Ultralow Loss Interconnection Technique for LTCC based System-in-Package(SIP) Technology at 60GHz

2006 ◽  
Vol 969 ◽  
Author(s):  
Dong-Young Kim ◽  
Jae Kyoung Mun ◽  
Dong-Suk Jun ◽  
Haechoen Kim
Keyword(s):  
Transmission Lines ◽  
Insertion Loss ◽  
Return Loss ◽  
Frequency Range ◽  
Transmission Characteristics ◽  
Transition Structure ◽  
Low Loss ◽  
Signal Line ◽  
The Difference ◽  
Packaging Module

AbstractThe effects of wire and ribbon bond interconnection on the transmission characteristics at millimeter wave frequency range was presented. The insertion loss and return loss was closely related with the ratio of the signal line width to that of bonded wire or ribbon. The most promise condition for low loss interconnection was that the width of bonded wire or ribbon should be compatible to the width of signal lines. In the actual fabrication of LTCC amp module, the insertion loss of packaging is very small which means that the loss due to bonding is nearly negligible. However, the S11 and S22 degraded severely due to the difference of the types of transmission lines between chip and packaging module. A new transition structure was introduced in order to compensate this difference of transmission lines.

Broadband Transition between Rectangular Waveguide and Substrate Integrated Waveguide Based on Double Rhombus Antenna Probe

2014 ◽  
Vol 668-669 ◽  
pp. 799-802
Author(s):  
Hai Yan Jin ◽  
Teng Yue
Keyword(s):  
Insertion Loss ◽  
Rectangular Waveguide ◽  
Return Loss ◽  
Substrate Integrated Waveguide ◽  
Metal Waveguide ◽  
Low Insertion Loss ◽  
Better Than ◽  
Good Agreement

The paper presents a design of rectangular waveguide-SIW transition, which provides a broadband and low insertion loss performance. The broadband transition is realized by using double-rhombus antenna probe inserted into rectangular metal waveguide. The transition is simulated and measured at 9-20GHz. The measured results show that a good agreement with simulation and an insertion loss less than 2.8 dB and a return loss better than 10 dB are obtained at 10–18.5 GHz for a back-to-back structure.

Sign in / Sign up

Export Citation Format

Share Document