A Study on the Possibility of Three-dimensional Wearable Respiration Rate Sensor based on Surface Area Changes

2018 ◽  
Vol 21 (1) ◽  
pp. 35-44 ◽  
Author(s):  
Seungpyo Lee ◽  
Hyunsung Ban ◽  
Joohyeon Lee
Keyword(s):  
Surface Area ◽  
Respiration Rate ◽  
Three Dimensional ◽  
Rate Sensor

Sensing efficiency of three-dimensional textile sensors with an open-and-close structure for respiration rate detection

2020 ◽  
Vol 90 (19-20) ◽  
pp. 2258-2274
Author(s):  
Jin-Hee Yang ◽  
Hyun-Seung Cho ◽  
Hwykuen Kwak ◽  
Je-Wook Chae ◽  
Hyeok-Jae Lee ◽  
...  
Keyword(s):  
Respiration Rate ◽  
Strain Gauge ◽  
3D Structure ◽  
Three Dimensional ◽  
Repeated Measurements ◽  
Frequent Occurrence ◽  
Body Contour ◽  
Wearable Systems ◽  
Textile Sensors ◽  
Rate Sensor

The strain-gauge type textile sensors adopted in many studies on respiration-sensing wearable systems have been reported to have two major limitations that result in reduced sensing accuracy and insufficient durability of the sensor. The two limitations are the inability to accurately monitor the changes in the three-dimensional (3D) body contour during changes in the respiration cycle and the frequent occurrence of baseline drifts. To solve these issues, this study proposes new types of textile respiration rate sensors with a 3D structure, which measure the respiration rate based on the variation in the size of the contacting section’s surface during respiration, rather than the changes in the length of the sensor, as in existing strain-gauge type sensors. Firstly, the sensing signals were analyzed based on morphology and size measurements. Then, the sensing reliability of three respiration rate sensor types, namely the no-filler, 3D hard, and 3D soft types, was analyzed by comparing their measurements with those of the SS5LB. Finally, the reproducibility and baseline drifts of the sensors’ measurements were evaluated by taking and comparing repeated measurements. As a result, the consistency of the sensing signals of the SS5LB and those of the two types of 3D sensors was higher than those of the no-filler type sensor, and the 3D soft type sensor had the highest reliability and reproducibility among the three new types of sensors. The result showed relatively reduced baseline drifts in the two types of 3D sensors.

Low-Degree Tibial Slope Angle Prevents Component Overhang by Enlarging the Lateral Plateau Surface Area in Total Knee Arthroplasty

2020 ◽  
Author(s):  
Mehmet Emin Simsek ◽  
Mustafa Akkaya ◽  
Safa Gursoy ◽  
Özgür Kaya ◽  
Murat Bozkurt
Keyword(s):  
Total Knee Arthroplasty ◽  
Surface Area ◽  
Knee Arthroplasty ◽  
Tibial Plateau ◽  
Slope Angle ◽  
Three Dimensional ◽  
Tibial Slope ◽  
Total Knee ◽  
Lateral Plateau ◽  
Gender Groups

AbstractThis study aimed to investigate whether overhang or underhang around the tibial component that occurs during the placement of tibial baseplates was affected by different slope angles of the tibial plateau and determine the changes in the lateral and medial plateau diameters while changing the slope angle in total knee arthroplasty. Three-dimensional tibia models were reconstructed using the computed tomography scans of 120 tibial dry bones. Tibial plateau slope cuts were performed with 9, 7, 5, 3, and 0 degrees of slope angles 2-mm below the subchondral bone in the deepest point of the medial plateau. Total, lateral, and medial tibial plateau areas and overhang/underhang rates were measured at each cut level. Digital implantations of the asymmetric and symmetric tibial baseplates were made on the tibial plateau with each slope angles. Following the implantations, the slope angle that prevents overhang or underhang at the bone border and the slope angle that has more surface area was identified. A significant increase was noted in the total tibial surface area, lateral plateau surface area, and lateral anteroposterior distance, whereas the slope cut angles were changed from 9 to 0 degrees in both gender groups. It was found that the amount of posteromedial underhang and posterolateral overhang increased in both the asymmetric and symmetric tibial baseplates when the slope angle was changed from 0 to 9 degrees. Although the mediolateral diameter did not change after the proximal tibia cuts at different slope angles, the surface area and anteroposterior diameter of the lateral plateau could change, leading to increased lateral plateau area. Although prosthesis designs are highly compatible with the tibial surface area, it should be noted that the component overhangs, especially beyond the posterolateral edge, it can be prevented by changing the slope cut angle in males and females.

3D reconstruction and calculation of surface area and volume of bell pepper

2007 ◽  
Vol 3 (1) ◽  
pp. 89-113
Author(s):  
Zoltán Gillay ◽  
László Fenyvesi
Keyword(s):  
3D Reconstruction ◽  
Surface Area ◽  
Three Dimensional ◽  
Reference Method ◽  
Bell Pepper ◽  
Three Dimensional Model ◽  
Acceptable Error ◽  
Volume Calculation ◽  
Bell Peppers ◽  
Area And Volume

There was a method developed that generates the three-dimensional model of not axisymmetric produce, based on an arbitrary number of photos. The model can serve as a basis for calculating the surface area and the volume of produce. The efficiency of the reconstruction was tested on bell peppers and artificial shapes. In case of bell peppers 3-dimensional reconstruction was created from 4 images rotated in 45° angle intervals. The surface area and the volume were estimated on the basis of the reconstructed area. Furthermore, a new and simple reference method was devised to give precise results for the surface area of bell pepper. The results show that this 3D reconstruction-based surface area and volume calculation method is suitable to determine the surface area and volume of definite bell peppers with an acceptable error.

Evaluation of a Three-Dimensional Stereophotogrammetric Method to Identify and Measure the Palatal Surface Area in Children with Unilateral Cleft Lip and Palate

2016 ◽  
Vol 53 (1) ◽  
pp. 16-21 ◽  
Author(s):  
Marcio De Menezes ◽  
Ana Maria Cerón-Zapata ◽  
Ana Maria López-Palacio ◽  
Andrea Mapelli ◽  
Luca Pisoni ◽  
...  
Keyword(s):  
Surface Area ◽  
Cleft Lip ◽  
Cleft Lip And Palate ◽  
Three Dimensional

Accelerating ion diffusion with unique three-dimensionally interconnected nanopores for self-membrane high-performance pseudocapacitors

Nanoscale ◽  
2017 ◽  
Vol 9 (46) ◽  
pp. 18311-18317 ◽  
Author(s):  
Yuan Gao ◽  
Yuanjing Lin ◽  
Zehua Peng ◽  
Qingfeng Zhou ◽  
Zhiyong Fan
Keyword(s):  
Aspect Ratio ◽  
Surface Area ◽  
Structural Stability ◽  
High Aspect Ratio ◽  
High Performance ◽  
Three Dimensional ◽  
Rate Capability ◽  
Large Surface Area ◽  
Nanoporous Structure ◽  
Ion Diffusion

Three-dimensional interconnected nanoporous structure (3-D INPOS) possesses high aspect ratio, large surface area, as well as good structural stability. Profiting from its unique interconnected architecture, the 3-D INPOS pseudocapacitor achieves a largely enhanced capacitance and rate capability.

Hierarchical Nano/Micro-structured Surfaces with High Surface Area/Volume Ratios

2021 ◽  
pp. 1-36
Author(s):  
Ketki Lichade ◽  
Yizhou Jiang ◽  
Yayue Pan
Keyword(s):  
Surface Structure ◽  
Surface Area ◽  
Light Trapping ◽  
High Surface ◽  
High Surface Area ◽  
Three Dimensional ◽  
Structure Design ◽  
Surface Structures ◽  
Structured Surfaces ◽  
Design And Manufacture

Abstract Recently, many studies have investigated additive manufacturing of hierarchical surfaces with high surface area/volume (SA/V) ratios, and their performance has been characterized for applications in next-generation functional devices. Despite recent advances, it remains challenging to design and manufacture high SA/V ratio structures with desired functionalities. In this study, we established the complex correlations among the SA/V ratio, surface structure geometry, functionality, and manufacturability in the Two-Photon Polymerization (TPP) process. Inspired by numerous natural structures, we proposed a 3-level hierarchical structure design along with the mathematical modeling of the SA/V ratio. Geometric and manufacturing constraints were modeled to create well-defined three-dimensional hierarchically structured surfaces with a high accuracy. A process flowchart was developed to design the proposed surface structures to achieve the target functionality, SA/V ratio, and geometric accuracy. Surfaces with varied SA/V ratios and hierarchy levels were designed and printed. The wettability and antireflection properties of the fabricated surfaces were characterized. It was observed that the wetting and antireflection properties of the 3-level design could be easily tailored by adjusting the design parameter settings and hierarchy levels. Furthermore, the proposed surface structure could change a naturally-hydrophilic surface to near-superhydrophobic. Geometrical light trapping effects were enabled and the antireflection property could be significantly enhanced (>80% less reflection) by the proposed hierarchical surface structures. Experimental results implied the great potential of the proposed surface structures for various applications such as microfluidics, optics, energy, and interfaces.

Sign in / Sign up

Export Citation Format

Share Document