scholarly journals CFD Investigation of A New Elliptical-Bladed Multistage Savonius Rotors

2020 ◽  
Vol 9 (3) ◽  
pp. 383-392
Author(s):  
Khalid Mrigua ◽  
Abdelghani Toumi ◽  
Mounia Zemamou ◽  
Bader Ouhmmou ◽  
Yahya Lahlou ◽  
...  
Keyword(s):  
Aspect Ratio ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Low Wind Speed ◽  
Coefficient Increase ◽  
Savonius Wind Turbine ◽  
Low Efficiency ◽  
Two Stages

The Savonius-conventional wind turbine is a class of wind turbines designed with a vertical axis. It has a good starting capacity and   an insensitivity to wind direction. It works relatively at low wind speed in an easy installation. Savonius wind turbine faces major drawbacks, including some of the low efficiency and high negative torque created by the returning blade. Many attempts have been undertaken to optimize the blade’s shape to increase the performance of these wind turbines. The vertical axis is still under development. The elliptical-blades with a cut angle equal 47.50° have recently shown enhanced performance. In this study, we investigate the effect of Elliptical-bladed multistage Savonius Rotors (rotor aspect ratio, stage aspect ratio) on the performance by means of numerical simulation. The results obtained by comparison of one, two, and three-stage rotors indicate that the maximum power coefficient increase with a number of the stages (for the rotors with similar RAR of 0.7). Moreover, for the rotors with similar SAR of 0.7, the two stages have the highest performance than others.©2020. CBIORE-IJRED. All rights reserved

scholarly journals Blades Optimization for Maximum Power Output of Vertical Axis Wind Turbine

2021 ◽  
Vol 10 (3) ◽  
pp. 585-595
Author(s):  
Ahmad Adnan Shoukat ◽  
Adnan Aslam Noon ◽  
Muhammad Anwar ◽  
Hafiz Waqar Ahmed ◽  
Talha Irfan Khan ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Edge Length ◽  
Research Network ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Low Wind Speed ◽  
Edge Profile ◽  
Power Yield

Wind power is a significant and urging sustainable power source asset to petroleum derivatives. Wind machines, for example, H-Darrieus vertical pivot wind turbines (VAWTs) have increased much notoriety in research network throughout the most recent couple of decades because of their applications at destinations having moderately low wind speed. Be that as it may, it is noticed that such wind turbines have low effectiveness. The point of this examination is to plan rotor cutting edges which could create most extreme power yield and execution. Different plan factors, for instance, harmony length, pitch edge, rotor distance across, cutting edge length and pitch point are explored to upgrade the presentation of VAWT. Rotor cutting edges are manufactured using the NACA-0030 structure and tried in wind burrow office and contrast its outcomes and DSM 523 profile. Numerical simulations are performed to get best geometry and stream conduct for achieving greatest power. It is seen that for higher tip-speed-proportion (TSR), shorter harmony length and bigger distance across the rotor (i.e., lower robustness) yields higher effectiveness in NACA 0030. Nevertheless, for lower TSR, the more drawn out agreement length and slighter distance across rotor (i.e., higher strength) gives better implementation. The pitch point is - 2° for TSR = 3 and - 3° for TSR = 2.5. The most extreme power yield of the wind turbine is acquired for the sharp edge profile NACA 0030. Besides, instantaneous control coefficient, power coefficient (CP) is the greatest reason for azimuthal edge of 245° and least esteem for 180°.

Optimized Small Vertical Axis Wind Turbine (VAWT), Phase I

2021 ◽  
Author(s):  
Moshe Zilberman ◽  
Abdelaziz Abu Sbaih ◽  
Ibrahim Hadad
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Cost Effective ◽  
Clean Energy ◽  
Vertical Axis ◽  
Low Noise ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Different Types

Abstract Wind energy has become an important resource for the growing demand for clean energy. In 2020 wind energy provided more than 6% of the global electricity demand. It is expected to reach 7% at the end of 2021. The installation growth rate of small wind turbines, though, is relatively slow. The reasons we are interested in the small vertical axis wind turbines are their low noise, environmentally friendly, low installation cost, and capable of being rooftop-mounted. The main goal of the present study is an optimization process towards achieving the optimal cost-effective vertical wind turbine. Thirty wind turbine models were tested under the same conditions in an Azrieli 30 × 30 × 90 cm low-speed wind tunnel at 107,000 Reynolds number. The different types of models were obtained by parametric variations of five basic models, maintaining the same aspect ratio but varying the number of bucket phases, the orientation angles, and the gaps between the vanes. The best performing turbine model was made of one phase with two vanes of non-symmetric bipolynomial profiles that exhibited 0.2 power coefficient, relative to 0.16 and 0.13 that were obtained for symmetrical polynomial and the original Savonius type turbines, respectively. Free rotation, static forces and moments, and dynamic moments and power were measured for the sake of comparison and explanation for the variations in performances of different types of turbines. CFD calculations were used to understand the forces and moment behaviors of the optimized turbine.

Four Decades of Research Into the Augmentation Techniques of Savonius Wind Turbine Rotor

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Nur Alom ◽  
Ujjwal K. Saha
Keyword(s):  
Wind Turbine ◽  
Turbine Rotor ◽  
Power Coefficient ◽  
Major Drawback ◽  
High Rotational Speed ◽  
Savonius Rotor ◽  
Augmentation Techniques ◽  
Savonius Wind Turbine ◽  
Low Efficiency ◽  
Wind Turbine Rotor

The design and development of wind turbines is increasing throughout the world to offer electricity without paying much to the global warming. The Savonius wind turbine rotor, or simply the Savonius rotor, is a drag-based device that has a relatively low efficiency. A high negative torque produced by the returning blade is a major drawback of this rotor. Despite having a low efficiency, its design simplicity, low cost, easy installation, good starting ability, relatively low operating speed, and independency to wind direction are its main rewards. With the goal of improving its power coefficient (CP), a considerable amount of investigation has been reported in the past few decades, where various design modifications are made by altering the influencing parameters. Concurrently, various augmentation techniques have also been used to improve the rotor performance. Such augmenters reduce the negative torque and improve the self-starting capability while maintaining a high rotational speed of the rotor. The CP of the conventional Savonius rotors lie in the range of 0.12–0.18, however, with the use of augmenters, it can reach up to 0.52 with added design complexity. This paper attempts to give an overview of the various augmentation techniques used in Savonius rotor over the last four decades. Some of the key findings with the use of these techniques have been addressed and makes an attempt to highlight the future direction of research.

scholarly journals An experimental study of the optimal design parameters of a wind power tower used to improve the performance of vertical axis wind turbines

2018 ◽  
Vol 10 (9) ◽  
pp. 168781401879954
Author(s):  
Soo-Yong Cho ◽  
Sang-Kyu Choi ◽  
Jin-Gyun Kim ◽  
Chong-Hyun Cho
Keyword(s):  
Experimental Study ◽  
Optimal Design ◽  
Wind Turbine ◽  
Wind Power ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Design Parameters ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines

In order to augment the performance of vertical axis wind turbines, wind power towers have been used because they increase the frontal area. Typically, the wind power tower is installed as a circular column around a vertical axis wind turbine because the vertical axis wind turbine should be operated in an omnidirectional wind. As a result, the performance of the vertical axis wind turbine depends on the design parameters of the wind power tower. An experimental study was conducted in a wind tunnel to investigate the optimal design parameters of the wind power tower. Three different sizes of guide walls were applied to test with various wind power tower design parameters. The tested vertical axis wind turbine consisted of three blades of the NACA0018 profile and its solidity was 0.5. In order to simulate the operation in omnidirectional winds, the wind power tower was fabricated to be rotated. The performance of the vertical axis wind turbine was severely varied depending on the azimuthal location of the wind power tower. Comparison of the performance of the vertical axis wind turbine was performed based on the power coefficient obtained by averaging for the one periodic azimuth angle. The optimal design parameters were estimated using the results obtained under equal experimental conditions. When the non-dimensional inner gap was 0.3, the performance of the vertical axis wind turbine was better than any other gaps.

scholarly journals Numerical Investigations of the Effects of the Rotating Shaft and Optimization of Urban Vertical Axis Wind Turbines

Energies ◽  
2018 ◽  
Vol 11 (7) ◽  
pp. 1870 ◽  
Author(s):  
Lidong Zhang ◽  
Kaiqi Zhu ◽  
Junwei Zhong ◽  
Ling Zhang ◽  
Tieliu Jiang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Suction Side ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Physical Parameters ◽  
Rotating Shaft ◽  
Vertical Axis Wind Turbines ◽  
Negative Effect

The central shaft is an important and indispensable part of a small scale urban vertical axis wind turbines (VAWTs). Normally, it is often operated at the same angular velocity as the wind turbine. The shedding vortices released by the rotating shaft have a negative effect on the blades passing the wake of the wind shaft. The objective of this study is to explore the influence of the wake of rotating shaft on the performance of the VAWT under different operational and physical parameters. The results show that when the ratio of the shaft diameter to the wind turbine diameter (α) is 9%, the power loss of the wind turbine in one revolution increases from 0% to 25% relative to that of no-shaft wind turbine (this is a numerical experiment for which the shaft of the VAWT is removed in order to study the interactions between the shaft and blade). When the downstream blades pass through the wake of the shaft, the pressure gradient of the suction side and pressure side is changed, and an adverse effect is also exerted on the lift generation in the blades. In addition, α = 5% is a critical value for the rotating shaft wind turbine (the lift-drag ratio trend of the shaft changes differently). In order to figure out the impacts of four factors; namely, tip speed ratios (TSRs), α, turbulence intensity (TI), and the relative surface roughness value (ks/ds) on the performance of a VAWT system, the Taguchi method is employed in this study. The influence strength order of these factors is featured by TSRs > ks/ds > α > TI. Furthermore, within the range we have analyzed in this study, the optimal power coefficient (Cp) occurred under the condition of TSR = 4, α = 5%, ks/ds = 1 × 10−2, and TI = 8%.

The Straight-Bladed Morphing Vertical Axis Wind Turbine

2016 ◽  
Author(s):  
David MacPhee ◽  
Asfaw Beyene
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Low Cost ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Pitch Control ◽  
Control Schemes ◽  
Horizontal Axis Wind Turbines ◽  
Novel Concept

Blade pitch control has been extremely important for the development of Horizontal-Axis Wind Turbines (HAWTs), allowing for greater efficiency over a wider range of operational regimes when compared to rigid-bladed designs. For Vertical-Axis Wind Turbines (VAWTs), blade pitching is inherently more difficult due to a dependence of attack angle on turbine armature location, shaft speed, and wind speed. As a result, there have been very few practical pitch control schemes put forward for VAWTs, which may be a major reason why this wind turbine type enjoys a much lower market share as compared to HAWTs. To alleviate this issue, the flexible, straight-bladed vertical-axis turbine is presented, which can passively adapt its geometry to local aerodynamic loadings and serves as a low-cost blade pitch control strategy increasing efficiency and startup capabilities. Using two-dimensional fluid-structure action simulations, this novel concept is compared to an identical rigid one and is proven to be superior in terms of power coefficient due to decreased torque minima. Moreover, due to the flexible nature of the blades, the morphing turbine achieves less severe oscillatory loadings. As a result, the morphing blade design is expected to not only increase efficiency but also system longevity without additional system costs usually associated with active pitch control schemes.

scholarly journals Effect of Concentrator, Blade Diameter and Blade Number on the Savonius Wind Turbine Performance

2017 ◽  
Vol 5 (2) ◽  
Author(s):  
Ida Bagus Alit ◽  
Rudy Sutanto ◽  
I Made Mara ◽  
Mirmanto Mirmanto
Keyword(s):  
Wind Turbine ◽  
Concentration Ratio ◽  
Turbine Blades ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Wind Speeds ◽  
Vertical Axis Wind Turbines ◽  
Negative Moment ◽  
Low Efficiency ◽  
Low Wind Speeds

Savonius turbine is a type of vertical-axis wind turbines. The turbine has a potential to be developed as it has a simple construction and is suitable for low wind speeds. However, the turbine is still rarely used because of the low efficiency of the turbine compared to other turbines. The low efficiency of the turbine is due to the negative moment. Some efforts have been done to reduce the negative moment such as by adding a wind concentrator. The wind concentrator can steer the incoming wind toward the turbine blades that generate positive moments, consequently, the generated power increases. The aim of this research is to determine the effect of the number and diameter of the Savonius blade wind turbine with an additional concentrator. The concentrator had a concentration ratio of 6:1 and it was tested at the lower wind speeds of 2-5 m/s. The result shows that adding a wind concentrator can increase the rotational speed of the rotor, power coefficient, and the turbine power. The Savonius turbine with two blades has the best performance compared to the three and four blades. The Savonius blade wind turbine with the rotor diameter of 12 cm is the best Savonius turbine for the concentration ratio of 6:1.

Wind tunnel and numerical study of multi-storey vertical axis wind turbines with different configurations

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Abhijeet M. Malge ◽  
Prashant Maruti Pawar
Keyword(s):  
Wind Tunnel ◽  
Wind Turbine ◽  
Wind Power ◽  
Wind Turbines ◽  
Numerical Study ◽  
Research Work ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Content Type ◽  
Vertical Axis Wind Turbines

Purpose Three different configurations of vertical axis wind turbines (VAWT) were fabricated by changing the storey height and their orientations. The purpose of this study is to find the effect of storey height and orientation on the performance of wind turbines. The multistory VAWT has three storeys. The first configuration had increased middle storey height, with 0–90-0 orientation of blades. Wherein the second turbine had equal storey heights. The third configuration had increased middle storey height with 0–120-240 orientation of blades. The blades were tested numerically and experimentally. Design/methodology/approach In this research work, prototypes of innovative multistory VAWT were built with different configurations and orientations. Three configurations of three-storey VAWT were fabricated by varying the height of storey of turbines. The orientations were made by keeping the storeys orthogonal to each other. Multistory VAWT was tested numerically and experimentally. ANSYS Fluent was used for computational fluid dynamic analysis of VAWT. K-epsilon model was used for numerical analysis of wind turbine. Experimentation was carried out in a wind tunnel for different tip speed ratios (TSR). Findings The three configurations of innovative multistory VAWT were tested numerically and experimentally for different TSR. It has been found that the VAWT with equal storey height had a better performance as compared to the other two configurations with increased middle storey height. The power coefficient of equal storey height VAWT was about 22%, wherein the power coefficient of turbines with reduced upper and lower storey height was between 5%–8% Research limitations/implications The research work of multi-storey VAWT is very novel and original. The findings of the research will contribute to the existing work done in the field of VAWT. This will help other researchers to have insight into the development of multistory VAWT. The effect of storey height and configuration of multi-storey VAWT is studied numerically and experimentally, which concludes that the performance of equal storey is superior as compared to other configurations. Practical implications The multi-storey concept of VAWT was developed to counter the problem of wind direction. The blades of each storey were arranged orthogonal to each other. This helped to harness wind power irrespective of the direction of the wind. This will make the VAWT more sustainable and financially viable for domestic use. Social implications The turbines are specially designed for remotely located housed in rural areas where the power grid is not yet reached. Users can install the turbine on their rooftop and harness wind power of 100 W capacity. This will help them to make their life easy. Originality/value This research work is very original and first of a kind. The multistory concept of the wind turbine was checked for the effect of storey height and orientations of blades on its performance. Different configurations and orientations of the vertical axis were designed and developed for the first time.

Wind Tunnel Experiment on the Aerodynamic Interaction Between Vertical Axis Wind Turbine Pair

2021 ◽  
Author(s):  
Hao Su ◽  
Haoran Meng ◽  
Jia Guo ◽  
Timing Qu ◽  
Liping Lei
Keyword(s):  
Wind Tunnel ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Power Performance ◽  
Array Configuration ◽  
Aerodynamic Interaction ◽  
Positive Effect

Abstract Wind energy has attracted worldwide attention as a pollution-free and widely distributed renewable energy source. Increasing the power density by optimizing the arrangement of wind turbines has been a popular field of research in recent years. In the present work, a systematic study on the influence of array configuration on vertical axis wind turbines is made through wind tunnel experiments. Firstly, the power performance of an isolated vertical axis wind turbine at different tip speed ratios is tested as a benchmark of comparison. Multiple situations of two-turbine configurations are then tested and the results are compared with the isolated wind turbine. The power coefficient of the turbine pair increases by 34% when the turbines are 2.4 rotor diameters apart and rotate in the same direction. In the counter-rotating co-leeward case, it is demonstrated that the turbine pairs will have a positive effect on each other when they are separated by 2.1 rotor diameters to 2.4 rotor diameters. The lateral spacing between the counter-rotating co-windward turbine pair should be greater than 1.5 rotor diameters to avoid turbulence interference between the rotors.

scholarly journals Preliminary Performance Tests and Simulation of a V-Shape Roof Guide Vane Mounted on an Eco-Roof System

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2846 ◽  
Author(s):  
Xiaohang Wang ◽  
Wentong Chong ◽  
Kokhoe Wong ◽  
Liphuat Saw ◽  
Sinchew Poh ◽  
...  
Keyword(s):  
Power Generation ◽  
Guide Vane ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Roof System ◽  
Low Wind Speed ◽  
Computational Fluid Dynamics Cfd ◽  
Power Generation System ◽  
Low Efficiency

The technical and economic features of a patented V-shape roof guide vane (VRGV) with a solar and wind power generation system mounted on an eco-roof system are presented in this paper. Moreover, this innovative VRGV was investigated on for the purpose of improving the performance of a vertical axis wind turbine (VAWT), which was installed on an eco-roof system to solve the low-efficiency power generation problem of the wind turbines under the condition of a low wind speed. This paper proposes a preliminary study for the performance of the VAWT with the VRGV on a building. This research used a mock-up building with a double slope roof, where a five straight-bladed VAWT was mounted and tested under two conditions, with and without the VRGV. From the comparative experiments, the self-starting performance and rotational speed of the VAWT mounted above a double slope roof with the VRGV have been significantly improved compared to the VAWT without the VRGV. Further, the power coefficient (Cp) of the VAWT can be augmented to about 71.2% increment due to the VRGV design. In addition, numerical simulations by computational fluid dynamics (CFD) were proposed to verify the augmented effect of the Cp of the VAWT under the influence of the VRGV in the experiment. Besides, economic estimation of the VRGV was conducted.

Sign in / Sign up

Export Citation Format

Share Document